Harbor Freight Tools 93532 Product manual

READ AND SAVE THESE INSTRUCTIONS.

RULES FOR SAFE OPERATION

1. WARNING! To reduce the risk of
fire or electric shock, do not use
this Fan with any solid-state speed
control device.

2. This appliance has a polarized plug
(one blade is wider than the other).
To reduce the risk of electric
shock, this plug is intended to fit
into a polarized outlet only one
way. If the plug does not fit fully
in the outlet, reverse the plug. If it
still does not fit, contact a qualified
electrician. Do not change the
plug in any way. Do not attempt to
defeat this safety feature.

3. Do not leave Fan running
while unattended.

4. Do not operate any fan with a
damaged cord or plug. Discard fan
or return to an authorized service
facility for examination and/or
repair.

5. Do not run cord under carpeting.
Do not cover cord with throw rugs,
runners, or similar coverings.
Arrange cord away from traffic area
and where it will not be tripped
over.

6. Never insert fingers, pencils, or any
other object through Front or Rear
Blade Guards.

7. Disconnect Fan when moving it
from one location to another.

8. Disconnect Fan before removing
grills for cleaning.

9. Be sure fan is on a stable
surface when operating to avoid
overturning.

10. DO NOT use fan in window.
Rain may create electrical hazard.

11. Complete the assembly of the fan
before switching on the fan.

12. Maintain labels and nameplates on
the fan.
If unreadable or missing, contact
Harbor Freight Tools for a
replacement.

13. Use only in dry areas.
Do not use in bathrooms, laundry
area, near sinks or other sources of
water.

14. This fan is not a toy.
Keep it out of reach of children.

15. WARNING: The cord of this product
contains lead, a chemical known
to the State of California to cause
cancer, and birth defects or other
reproductive harm. Wash hands after
handling. (California Health & Safe­ty Code § 25249.5, et seq.)

16. People with pacemakers should
consult their physician(s) before
use. Electromagnetic fields in close
proximity to heart pacemaker could
cause pacemaker interference or
pacemaker failure.

17. The warnings, precautions, and
instructions discussed in this
instruction manual cannot cover all
conditions and situations that may
occur. It must be understood by
operator that common sense and
caution are factors which cannot
be built into this fan, but must be
supplied by operator.

Item 93532 For technical questions, please call 1-888-866-5797. Page 2

WARNING SYMBOLS AND DEFINITIONS

This is the safety alert symbol. It is used to alert you to

potential personal injury hazards. Obey all safety messages

that follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Addresses practices not related to personal injury.

Specifications

Fan Blade 24”

Fan Guard
Diameter

Motor 120 VAC, Single Phase

Amperage High -1.85, Low - 1.45

24-1/4”

Continuous Duty

E186832

Item 93532 For technical questions, please call 1-888-866-5797. Page 3

UNPACKING

When unpacking, check to make sure all the parts shown on the Parts List on page 8
are included. If any parts are missing or broken, please call Harbor Freight Tools at the
number shown on the cover of this manual as soon as possible.

ASSEMBLY AND OPERATING INSTRUCTIONS

NOTE: For additional information regarding the parts listed in the following pages, refer

to the Assembly Diagram on page 9.

Warning! Always make sure the Power Cord of the Fan is unplugged from its electrical

outlet prior to making any adjustments to the fan.

Warning! To reduce the risk of fire or electric shock, do not use this fan with any solid-

state speed control device.

ASSEMBLY

1. Attach the two Wheels (10) to the Drum (3) using three Bolts (11) per Wheel.

2. Assemble the Base (12) to the Drum (3) using the four Bolts (11).

3. Inspect the fully assembled fan with it resting on its wheels and the base.

IMPORTANT: The Pads at the bottom of the Base MUST sit flat on the floor.
If they do not, remove the Base (12), turn it 180°, and reinstall it.

OPERATION

1. Situate the Fan in a dry location out of children’s reach and away from normal
room traffic.

2. Plug in the Power Cord (8).

3. Set the Control (7) to either LOW or HIGH, depending on your preference.

4. When finished, set the Control (7) to OFF.

Item 93532 For technical questions, please call 1-888-866-5797. Page 4

INSPECTION, MAINTENANCE, AND CLEANING

1. WARNING! Make sure the Control (7) of the Fan is in its “OFF” position
and that the Fan is unplugged from its electrical outlet before performing any
inspection, maintenance, or cleaning procedures.

2. BEFORE EACH USE, inspect the general condition of the Fan. Check for
loose screws, misalignment or binding of moving parts, cracked or broken
parts, damaged electrical wiring, and any other condition that may affect its safe
operation. If abnormal noise or vibration occurs, have the problem corrected
before further use.

Do not use damaged equipment.

3. Periodically, check to see that the Blade (4) has no dirt or debris accumulating on
its surface. If necessary, use compressed air to clean the unit.

4. Before each use, check that the Power Cord (8) has no tears, frays, or cracks. Do
not use the Fan if you find any irregularities. Contact a qualified service technician.

Item 93532 For technical questions, please call 1-888-866-5797. Page 5

PARTS LIST

Part Description Qty.

1 Screw 12
2 Front Guard 1
3 Drum 1
4 Blade 1
5 Set Screw 1
6 Rear Guard 1
7 Control 1
8 Power Cord 1

9 Motor 1
10 Wheel 2
11 Bolt 10
12 Base 1

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER
THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR
SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS
TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS
OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Item 93532 For technical questions, please call 1-888-866-5797. Page 6

ASSEMBLY DIAGRAM

7

1

6

5

4

3

8

9

10

11

2

1

12

NOTE: Some parts are listed and shown for illustration purposes only, and are not

available individually as replacement parts.

Item 93532 For technical questions, please call 1-888-866-5797. Page 7

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality
and durability standards, and warrants to the original purchaser that this product is free
from defects in materials and workmanship for the period of 90 days from the date of
purchase. This warranty does not apply to damage due directly or indirectly, to misuse,
abuse, negligence or accidents, repairs or alterations outside our facilities, criminal
activity, improper installation, normal wear and tear, or to lack of maintenance. We
shall in no event be liable for death, injuries to persons or property, or for incidental,
contingent, special or consequential damages arising from the use of our product.
Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY
IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the
complaint must accompany the merchandise. If our inspection verifies the defect, we
will either repair or replace the product at our election or we may elect to refund the
purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that
the defect resulted from causes not within the scope of our warranty, then you must
bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which
vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797