Harbor Freight Tools 93468 User Manual

Page 1
®
CUP TYPE OIL FILCUP TYPE OIL FIL
CUP TYPE OIL FIL
CUP TYPE OIL FILCUP TYPE OIL FIL
WRENCH SETWRENCH SET
WRENCH SET
WRENCH SETWRENCH SET
TERTER
TER
TERTER
93468
ASSEMBLY AND OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright © 2005 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
Page 2
Specifications
Item Description
Purpose To remove oil filters from most domestic and import
cars and light trucks. Oil Filter Cup Sizes with number of flutes in cup Cup Material Stamped steel Cup Driver 3/8 inch Cup Depth 1-3/8 to 1-11/16 inches Weight 4.4 lbs.
65 mm 14, 65/67 mm 14, 68 mm 14, 73 mm 14, 74/76
mm 15, 76 mm 14, 76 mm 30, 75/77 mm 15, 80 mm
15, 80/82 mm 15, 90 mm 15, 93 mm 15, 93 mm 36,
100 mm 15
Save This Manual
You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING: When using tool, basic safety precautions should always be fol­lowed to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this tool!
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Do not use machines or power tools in
damp or wet locations. Don’t expose to rain. Keep work area well lighted. Do not use electrically powered tools in the presence of flammable gases or liquids.
3. Keep children away. Children must never be allowed in the work area. Do
not let them handle machines, tools, or extension cords.
4. Store idle equipment. When not in use, tools must be stored in a dry
location to inhibit rust. Always lock up tools and keep out of reach of children.
5. Use the right tool for the job. Do not attempt to force a small tool or
attachment to do the work of a larger industrial tool. There are certain applications for which this tool was designed. It will do the job better and more safely at the rate for which it was intended. Do not modify this tool and do not use this tool for a purpose for which it was not intended.
SKU 93468 For technical questions, please call 1-800-444-3353 Page 2
Page 3
6. Dress properly. Do not wear loose clothing or jewelry as they can be caught
in moving parts. Protective, electrically nonconductive clothes and nonskid footwear are recommended when working. Wear restrictive hair covering to contain long hair.
7. Use eye and ear protection. Always wear ANSI approved impact safety
goggles. Wear a full face shield if you are producing metal filings or wood chips. Wear an ANSI approved dust mask or respirator when working around metal, wood, and chemical dusts and mists.
8. Do not overreach. Keep proper footing and balance at all times. Do not
reach over or across running machines.
9. Maintain tools with care. Keep tools clean for better and safer performance.
10. Stay alert. Watch what you are doing, use common sense. Do not operate
any tool when you are tired.
11. Check for damaged parts. Before using any tool, any part that appears
damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment and binding of moving parts; any broken parts or mounting fixtures; and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician.
12. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools.
13. Do not operate tool if under the influence of alcohol or drugs. Read
warning labels if taking prescription medicine to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool.
14. Maintenance. For your safety, service and maintenance should be
performed regularly by a qualified technician.
Product Specific Safety Precautions
1. Avoid burns from hot oil. Allow vehicle engine to cool down before
removing oil filter. Oil streaming down may splash and strike the head or body of the operator.
2. Secure vehicle before working underneath. When using vehicle stands to
support the vehicle, make sure that the stands are placed in the correct position as described in the vehicle maintenance manual, and the emergency brake is set. Do not rely on a jack to support the vehicle.
SKU 93468 For technical questions, please call 1-800-444-3353 Page 3
Page 4
Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are fac­tors which cannot be built into this product, but must be supplied by the opera­tor.
Unpacking
When unpacking, check to make sure the following parts are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual.
3/8” Socket
Oil Filter Cups
Driver (15)
Operation
Warning: The vehicle engine must never be started in a closed garage, or any other sealed structure. Carbon monoxide is produced during operation and is deadly in a closed environment. Early signs of carbon monoxide poisoning resemble the flu, with headaches, dizziness, or nausea. If you have any of these signs get fresh air immediately.
1. Select the appropriate Oil Filter Cup by size specification of the oil filter, and the number stamped on the Oil Filter Cup.
2. Snap in the 3/8” Socket Driver (15) into the bottom of the selected Oil Filter Cup.
3. Snap in the other end of the 3/8” Socket Driver (15) into the 1/2” socket wrench (not supplied).
4. Press the Oil Filter Cup over the Oil Filter as far as it will go.
5. Place an oil pan, or other oil recovery devise, under the oil filter to catch the draining oil.
6. Turn socket wrench counterclockwise until oil filter is removed.
7. Install a new oil filter by first lubricating the new filter gasket, then hand-screw the filter in place until tight.
SKU 93468 For technical questions, please call 1-800-444-3353 Page 4
Page 5
Caution: Always dispose of used oil properly.
Contact your local Hazardous Waste Authority for proper disposal guidelines.
Maintenance
1. Thoroughly clean the Oil Filter Cups before storing.
2. Store all Oil Filter Cups and 3/8” Socket Driver (15) back in the Molded Case (16) when finished.
Parts List
Item Description Qty
1. Cup, 65 mm x 14 * 1
2. Cup,65/67 mm x 14 1
3. Cup,68 mm x 14 1
4. Cup, 73 mm x 14 1
5. Cup, 74/76 mm x 15 1
6. Cup, 76 mm x 14 1
7. Cup, 76 mm x 30 1
8. Cup, 75/77 mm x 15 1
9. Cup, 80 mm x 15 1
10. Cup, 80/82 mm x 15 1
11. Cup, 90 mm x 15 1
12. Cup, 93 mm x 15 1
13. Cup, 93 mm x 36 1
14. Cup, 100 mm x 15 1
15. 3/8” Socket Driver 1
16. Case, Blow Mold 1
* (# of Flutes in cup)
NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 93468 For technical questions, please call 1-800-444-3353 Page 5
Loading...