Harbor Freight Tools 92049 Assembly And Operating Instructions Manual

BEVERAGE HOLDERBEVERAGE HOLDER

BEVERAGE HOLDERBEVERAGE HOLDER

BEVERAGE HOLDER

INSULAINSULA

INSULAINSULA

INSULA

TED - 12 VDCTED - 12 VDC

TED - 12 VDCTED - 12 VDC

TED - 12 VDC

ASSEMBLY AND OPERATING INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at http://www.harborfreight.com

Copyright © 2004 by Harbor Freight Tools®. All rights reser ved. No por tion of this
manual or any artwork contained herein may be reproduced in any shape or for m
without the express written consent of Harbor F reight T ools .

For technical questions and replacement parts, please call 1-800-444-3353

92049

SKU 92049 Page 2

Specifications

ITEM DESCRIPTION

Bottle C apacity 32 fluid ounces
Cup C apacity 12 fluid ounces
Pow er C onsumption 12 VD C from vehicle pow er socket
P o we r Co rd 5 fe e t, 1 8 A W G c a b le, v e h ic le cig a r e tte

lighter adapter plug

W arming Temperature

150 degrees F, ± 10 degrees
Fuse 10 am p fuse inside adapter plug
Bottle M aterial Stainless steel
O verall Dimensions 11.5 (H) x 3.75 (dia.) inches
W eig h t 2 lb s . (e m p ty )

Save This Manual

You will need the manual for the saf ety w arnings and precautions, assembly
instructions, and operating and maintenance procedures. Keep your in voice with
this manual. Write the invoice number on the inside of the front co v er. Keep the
manual and inv oice in a safe and dry place for future reference.

Safety Warnings and Precautions

Warning: When using this product, basic safety precautions should always be
followed to reduce the risk of personal injury and damage to unit.

Read all instructions before using this tool!

1. Disconnect power when not in use.

2. Do not drink directly from the heated Bever age Holder.

3. Do not overfill, tilt or shak e immediately after filling with a hot be v erage .

4. Do not touch the inside of the Bev erage Holder when hot.

5. Do not connect the Bev er age Holder pow er cord to a 12 VDC sock et when
cold bev erages are contained.

6. Do not operate the Bev erage Holder if the po w er cord or connector are
damaged.

7. Do not submerge the Bever age Holder in water.

8. Do not expose the operating Be v erage Holder to e xtreme , e xternal heat.

9. Do not overtighten the Dispenser Cap or Cup.

10. Not intended for use by children.

SKU 92049 Page 3

11. Nev er leav e the Beverage Holder unattended while connected to the 12 VDC
power source.

12. Dairy and other beverages that spoil easily should not be contained f or
prolonged periods of time.

13. Close Dispenser Valve and secure the stainless steel Cup when beverages
are contained.

14. Before using this product, any part that appears damaged should be carefully
checked to determine that it will operate properly. Any part that is damaged
should be properly repaired or replaced by a qualified technician.

Note: Performance of this product may va ry depending on variations in vehicle bat­tery power.

Warning: The warnings, cautions, and instructions discussed in this instruc­tion manual cannot cover all possible conditions and situations that ma y oc­cur. It must be understood by the operator that common sense and caution
are factors which cannot be built into this product, but must be supplied by
the operator .

Unpacking

When unpacking, check to mak e sure the following parts are included. If any parts
are missing or broken, please call Harbor F reight Tools at the number on the cover
of this manual.

Cup

Beverage
Container

Dispenser
Valve Cap

Handle

Carrying Strap

Fused Plug

12 VDC Power Cord

SKU 92049 Page 4

Operation

1. Before you begin using unscre w the Cup and Dispenser Valve Cap and wash
the interior of the container with mild soap and warm water. Wash the Cup .
Rinse well. Refer to the photos on the previous page.

Caution: Do not place unit in a bath of water. This may damage the electrical
components of the unit.

2. Fill the Bev erage Holder with the desired drink or liquid f ood.

3. Screw in (clockwise) the Dispenser Valve Cap .

4. Plug one end of the Po w er Cord into the bottom of the Be v er age Container
and the Fused Plug into a 12 VDC vehicle power sock et.

This will heat up the contents and keep it warm. When the Po w er Cord is
unplugged, the contents will keep warm for a period of time.

Note: If the stored drink is to be kept cool, do not plug in the Pow er Cord.

5. To pour a drink from the Beverage Holder, press in on the Dispenser Valve
Cap until it locks in the down position, then pour.

If the contents are of a thick consistency
(such as soup), unscrew the Dispenser
V alv e Cap and pour out the contents .

6. Replace the Dispenser Valve Cap and
press in on the cap button to lock.

7. Wash container after each use .

8. Store unit with Po w er Cord in the factory
box when not in use.

Maintenance / Cleaning

1. This product has no replaceable parts.

2. After each use, place warm water and mild soap inside the Beverage Holder
to clean. Do not submerge unit into w ater.

3. If the unit does not warm up, the 10A fuse in the Fused Plug ma y need
replacement. Unscre w the plug cap to view and replace fuse. If the fuse is
good, the unit is not receiving power, or it is defective and needs servicing by
a qualified technician.