Page 1
METAL
WOOD RACK (2 PCS.)
ASSEMBLY INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
Copyright © 2004 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
92021
®
Page 2
SKU 92021 For technical questions, please call 1-800-444-3353. Page 2
Specifications
Save This Manual
You will need the manual for the safety warnings and precautions, assembly
instructions, operating and maintenance procedures, parts list and diagram. Keep
your invoice with this manual. Write the invoice number on the inside of the front
cover. Keep the manual and invoice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING: When using this product, basic safety precautions should always
be followed to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this product!
1. Keep work area clean. Cluttered areas invite injuries.
2. Use eye and ear protection. Always wear ANSI approved impact safety
goggles when assembling this product. Goggles are available from Harbor
Freight Tools.
3. Stay alert. Watch what you are doing, use common sense. Do not assemble
this product when you are tired.
4. Do not let children play around this product. Do not let children climb on
this product. This is a product for storage, not for climbing.
4. Check for damaged parts. Before using this product, any part that appears
damaged should be carefully checked to determine that it will operate
properly and perform its intended function. Check for loose parts and any
other condition that may affect the operation of this product. Replace loose
or worn parts immediately. Any part that is damaged should be properly
repaired or replaced.
5. Replacement parts. When servicing, use only identical replacement parts.
Use of any other parts will void the warranty.
6. Mount Wood Rack in solid studs on the wall. The weight capacity of this
product is largely dependent on the method of installation and hardware
used. (Hardware is not provided). If in doubt of it’s stability, have a
professional carpenter install this product. Harbor Freight Tools is not
responsible for accidents due to poor installation. The weight capacity
suggested per shelf is 100 lbs. when two Metal Wood Racks are mounted
side by side. Do not exceed.
Upright Bracket
Rack Dimension
Materials
Weight Shelf Capacity
40-1/2” Long X 14-1/2” Wide X 1/16” Thickness Qty 2
13-1/2” Long X 1-1/4” Wide X 1/16” Thickness-Qty. 12
Low Carbon Steel Tubing-Powder Coated Black
100 Lbs. per Shelf (when two Metal Wood Racks are mounted
side by side).
Page 3
SKU 92021 For technical questions, please call 1-800-444-3353. Page 3
Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that
may occur. It must be understood by the operator that common sense and
caution are factors which cannot be built into this product, but must be
supplied by the operator.
Unpacking
When unpacking, check to make sure the following parts are included. If any
parts are missing or broken, please call Harbor Freight Tools at the number on
the cover of this manual.
Assembly Instructions
1. Position Upright Brackets (1) six feet apart. Be sure to select the correct
hardware for mounting the Upright Brackets into solid studs in the wall. Use
the white plastic Spacer (5) when mounting.
See Figures 1 & 2.
2. Attach the Endcaps (3) to the ends of the Racks (2). (Not shown).
3. If boards longer than 8’ are used, it is suggested you purchase a second set
of wall mounted Wood Racks to accommodate that length. Do not exceed the
100 lbs. per shelf limit when Metal Wood Racks are mounted side by side.
A multipurpose storage rack used to hold timber, pipe, or other building materials*.
Can be used in workshops, garages, sheds or etc. Six levels, each level holding no
more than 100 lbs. Each Metal Wood Rack must be secured to a solid wood stud
using 3 screws per Upright Bracket (1). Recommended hardware is 3” Wood
Screws x 1/4” diameter-Grade 5. (Hardware not included).
*If round materials are stored on the rack they must be tied securely to the rack.
Figure 1
Upright
Bracket (1)
Rack (2)
Endcaps (3)
(not show)
Figure 2
Spacer (5)
Spacer (5)
(on back of
Upright
Brackets)
6
Upright
Bracket (1)
Page 4
SKU 92021 For technical questions, please call 1-800-444-3353. Page 4
Parts List
Part # Description Qty.
Assembly Drawing
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO
REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY
CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK
AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS
THERETO.
NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts.
2
12
12
12
6
Upright Bracket
Racks
Endcaps (not shown)
Screw
Spacer
1
2
3
4
5
Part 1
Part 1
Part 2
Wood Board
shown for
example only.
Not included.
Part 2
Part 3 (not shown)
Part 5
(not shown)
Loading...