Page 1
PROPANE TORCH
WITH 3 BURNERS
91899
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
Copyright© 2004 by Harbor F reight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or
form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.
Page 2
Specifications
Fuel Compatibility LP Gas (Standard Propane)
Number of Burners 3
Hose Working Pressure 350 PSI
Hose Length 44”
Gas Bottle Type Camping Propane Bottle (not included)
Bottle Thread Mounting Standard without Ring Seal (1”-20 TPI)
Tips: Flat Flame Tip, Pipe Heating Tip, Soldering Tip
Save This Manual
You will need the manual for the safety warnings and precautions, assembly instructions,
operating and maintenance procedures, parts list and diagram. Keep your invoice with this
manual. Write the invoice number on the inside of the front cover. Keep the manual and
invoice in a safe and dr y place for future reference.
Safety Warnings and Precautions
WARNING: When using tool, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.
Read all instructions before using this tool!
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Do not use tools in damp or wet locations. Don’t
expose to rain. Keep work area well lighted.
3. Keep children away. Children must never be allowed in the work area. Do not let
them handle the Torch.
4. Store idle equipment. When not in use, tools must be stored in a dry location to
inhibit rust. Always lock up tools and keep out of reach of children.
5. Use the right tool for the job. Do not attempt to force a small tool or attachment to
do the work of a larger industrial tool. There are cer tain applications for which this tool
was designed. It will do the job better and more safely at the rate for which it was
intended. Do not modify this tool and do not use this tool for a purpose for which it
was not intended.
6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in
moving parts. Protective, electrically nonconductive clothes and nonskid footwear are
recommended when working. Wear restrictive hair covering to contain long hair.
7. Use eye protection. Always wear ANSI approved impact safety goggles and heatresistant work gloves. Wear a full face shield if you are producing metal filings or
wood chips. Wear an ANSI approved dust mask or respirator when working around
metal, wood, and chemical dusts and mists.
8. Do not overreach. Keep proper footing and balance at all times. Do not reach over
or across hot torches or work pieces.
Page 2SKU 91899 For replacement parts please call 1-800-444-3353.
Page 3
9. Maintain tools with care. Keep tools clean for better and safer performance. Follow
instructions for lubricating and changing accessories. Inspect tool hoses periodically,
and if damaged, have them repaired by an author ized technician. The handle must be
kept clean, dry, and free from oil and grease at all times.
10. Disconnect fuel. Disconnect from Propane tank when not in use.
11. Stay alert. Watch what you are doing, use common sense. Do not operate any tool
when you are tired.
12. Check for damaged parts. Before using any tool, any part that appears damaged
should be carefully checked to determine that it will operate properly and perform its
intended function. Check for alignment and binding of moving parts; any broken parts
or mounting fixtures; and any other condition that may affect proper operation. Any
part that is damaged should be properly repaired or replaced by a qualified
technician.
13. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use accessories
intended for use with this tool. Approved accessories are available from Harbor
Freight Tools.
14. Do not operate tool if under the influence of alcohol or drugs. Read warning
labels if taking prescription medicine to determine if your judgment or reflexes are
impaired while taking drugs. If there is any doubt, do not operate the tool.
15. Maintenance. For your safety, service and repairs should be performed regularly only
by a qualified technician. Maintenance should be performed regularly.
Warning: The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be
built into this product, but must be supplied by the operator.
WARNING: This product, when used with propane for soldering and similar applica-
tions, pr oduces chemicals known to the State of California to cause
cancer and birth defects (or other reproductive harm).
(California Health & Safety Code § 25249.5
WARNING: The brass components of this product contain lead, a chemical known
to the State of California to cause birth defects (or other reproductive
harm). (California Health & Safety code § 25249.5, et seq.)
et seq.
)
Unpacking
When unpacking, check to make sure the parts listed on page 7 are included. If any parts
are missing or broken, please call Harbor Freight Tools at the number on the cover of this
manual as soon as possible.
Page 3SKU 91899 For replacement parts please call 1-800-444-3353.
Page 4
Specific Product Warnings and Precautions
1. The Propane Torch is for outdoor use only. Use the Propane Torch only in well
ventilated areas. Keep Propane Torch away from structures and flammable
materials. Inhalation of propane fumes may result in CARBON MONOXIDE
POISONING, INJURY AND/OR DEATH.
2. Risk of EXPLOSION
Propane fuel is EXTREMELY FLAMMABLE and under PRESSURE.
a. Contact local solid waste authorities for instructions on correct disposal
or recycling of propane cylinders. Never puncture or set fire to any empty
propane cylinder.
b. Never use a propane tank if it shows signs of: dents, corrosion, gouges,
bulges, fire damage, leakage, excessive rust, or any other form of visual
external damage.
c. Store propane cylinders properly:
- Store cylinders in a well ventilated area marked for cylinder storage only.
- Store propane cylinders away from oxidizing or corrosive gas cylinders.
- Store empty cylinders away from full cylinders, and label them clearly.
- Do not store propane fuel in temperatures exceeding 120° F.
Risk of FIRE
3. a. Before each use, always check all propane connections and joints to
make sure no leaks are present. Also check hoses for cracks or excessive
wear. Always replace a damaged hose.
b. If you notice the odor of propane while using the Torch, immediately
shut off the propane tank fueling the Torch. Extinguish all open flames
and carefully check for leaks by using soapy water. Never use a flame to
check for leaks. If the odor continues, do not use the Torch and move the
propane tank outside, if it is not already outside. Call your local propane
supplier for assistance.
c. Make sure the Hand Wheel (9) is turned to its “OFF” position and the
propane tank (not included) is removed from the Cylinder Connection (3)
when the Torch is not in use.
d. Never use gasoline, kerosene, or other highly volatile fluids as a starter
as they can explode.
e. Never leave the Propane Torch unattended once it is lit.
f. Keep a fire extinguisher handy. Always keep a commercial fire extinguisher
nearby the Propane Torch in case of accidental fire.
g. Do not clean the Propane Torch with combustible or corrosive cleaners.
h. Do not paint any part of the Propane Torch.
i. Never smoke while using the Propane Torch. Make sure all surrounding
flames are extinguished.
j. Do not use the product with any fuels other than pr opane.
Page 4SKU 91899 For replacement parts please call 1-800-444-3353.
Page 5
Specific Product Warnings and Precautions (continued)
4. All tips and burners get VER Y HOT during use.
a. Do not aim the Propane Torch at yourself, others, or animals. Keep spec-
tators clear of the work area.
b. Always allow sufficient time f or the Propane T o rch to completely cool down
before storing.
5. Do not store flammable liquids or materials in the area surrounding the Propane
Torch.
6. Maintain a firm grip with both hands while using the Propane Torch.
7. Never reach across the Propane Torch while in use. Be aware that parts of the
Propane Torch become very hot during use.
8. Maintain labels and nameplates on the Propane Torch. These carry important
information. If unreadab le or missing, contact Harbor Freight Tools for a replacement.
Assembly
Refer to the Assembly Drawing on page 8.
1. The Hand Wheel (9) on the Propane Torch controls the gas flow. Turn the Hand Wheel
(9) clockwise, all the way, into the “OFF” position.
2. Choose the appropriate Tip for your application (Flat Flame Tip (13), Hose Tip (15),
Soldering Tip (16)). Then, scre w the Tip onto the Nozzle Holder (30).
3. Attach the Cylinder Connection (3) to the outlet valve on the Propane Cylinder (not
included). Read and follow all of the “safety” and “usage” instr uctions that came with
the Propane Cylinder (not included).
Page 5SKU 91899 For replacement parts please call 1-800-444-3353.
Page 6
Operation
1. To light the Propane Torch, turn the Hand Wheel (9) counterclockwise to the Torch’s
“ON” position. T urn the Small Hand Wheel (24) clockwise to the Torch’ s “OFF” position.
Insert the lit end of a long handled, fireplace/barbecue grill lighter (not included) into
end of the Tip at the end of the Torch. Turn the Small Hand Wheel (24)
wise to the Torch’s “ON” position. Adjust the flame to the desired level by turning the
Small Hand Wheel (24).
Note: The lit Tips should operate with a b lue flame, with a small yello w tip. If the flame
is sputtering or popping, adjust the flame with the Small Hand Wheel (24).
2. To extinguish the flame , turn the Small Hand Wheel (24) clockwise “OFF” until closed.
Also, close the Hand Wheel (9). Disconnect the Cylinder Connection (3) from the
Propane Cylinder (not included).
Warning!! The Tip end of the Propane Torch will remain very hot after use. Allow it
cool before changing or removing nozzles, or storage.
3. Store the Propane Torch and Propane Cylinder (not included) in a safe place, out of
reach of children.
counterclock-
Maintenance
1. Before each use, inspect the gener al condition of the Propane Torch. Check for loose
bolts and nuts, misalignment or binding of moving parts, loose connections and joints,
cracked, bent, or broken par ts, excessively worn Hose (33), and any other condition
that may affect its safe operation. If a problem occurs, have the problem corrected
before further use. Do not use damaged equipment.
2. When cleaning, use only water and a mild detergent. Do not use cleaners that are
combustible or corrosive.
3. When storing, always allow sufficient time for the Propane Torch to completely cool
down. Do not store flammable liquids or materials in the area surrounding the Propane
Torch. Make sure the Hand Wheel (9) is in its “OFF” position and that the Torch is
disconnected from the Propane Cylinder (not included).
Page 6SKU 91899 For replacement parts please call 1-800-444-3353.
Page 7
Parts List
Part No. Description
1 Gas Inlet
2 Gasket
3 Cylinder Connection
4 0-ring
5 Body Tap
6 Nut Key/Needle Stop
7 0-ring
8 Needle
9 Hand Wheel
10 Nut M4
11 Hose Holder
12 Clip
13 Flat Flame Tip
14 Connector
15 Hose Tip
16 Soldering Tip
17 Clamp
18 Screw/ Nut M4
19 Washer
20 Handle
21 Tube
22 Body Tap
23 Needle
24 Small Hand Wheel
25 Nut M4
26 Nut Key/Needle Stop
27 0-ring
28 Extension Bar
29 Nozzle Gasket
30 Nozzle Holder
31 Nozzle
32 Gas/Air Mixer
33 Hose
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUF ACTURER AND/OR DISTRIBUT OR HAS PRO VIDED THE PAR TS DIAGRAM IN THIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUF A CTURER NOR DISTRIBUTOR
MAKES ANY REPRESENTATION OR W ARRANTY OF ANY KIND TO THE B UYER THAT HE OR
SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATES THA T ALL REP AIRS AND PAR TS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NO T BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT P AR TS THERET O , OR ARISING
OUT OF HIS OR HER INST ALLATION OF REPLA CEMENT P AR TS THERETO .
NOTE: Some par ts are listed and shown for illustration pur poses only and are not available
individually as replacement parts.
Page 7SKU 91899 For replacement parts please call 1-800-444-3353.
Page 8
Assembly Drawing
Page 8SKU 91899 For replacement parts please call 1-800-444-3353.
Loading...