Harbor Freight Tools 91883 Product manual

4-TIER SHELVING RACK

Model

91883

ASSEMBLY INSTRUCTIONS

Visit our website at: http://www.harborfreight.com

Read this material before using this product.

Failure to do so can result in serious injury.
SAVE THIS MANUAL.

Copyright© 2004 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any
artwork contained herein may be reproduced in any shape or form without the express written
consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described
herein. Tools required for assembly and service may not be included.

For technical questions or replacement parts, please call 1-800-444-3353.

Manual Revised 10g

SPECIFICATIONS

Overall Dimensions 51-5/8” H X 23” W X 12” D
Shelve Spacing 14-1/2” High
Materials H/D Polypropylene
Capacity per Shelf 44 lb. (dead weight)

Total Capacity 176 lb. (evenly distributed)

SAVE THIS MANUAL

You will need the manual for
the safety warnings and precautions,
assembly instructions, operating and
maintenance procedures, parts list and
diagram. Keep your invoice with this
manual. Write the invoice number on the
inside of the front cover. Keep the manual
and invoice in a safe and dry place for
future reference.

parts and any other condition that
may affect the use of this product.
Replace loose or worn parts
immediately. Any part that is damaged
should be properly repaired or
replaced.

Replacement parts5. . When servicing,
use only identical replacement parts.
Use of any other parts will void the
warranty.

Distribute weight evenly.6. Uneven
weight distribution could cause
tipping. Put heavier items on lower
shelves. Maximum weight per shelf is
44 lb. Do not allow children to climb
on the shelves as Shelving Rack
could trip over. Avoid setting up the
Shelving Rack on an uneven surface.

SAFETY WARNINGS AND

PRECAUTIONS

WARNING: When using this product,

basic safety precautions should
always be followed to reduce the
risk of personal injury and damage
to equipment.

Read all instructions before

assembling this product!

Keep work area clean1. . Cluttered

areas invite injuries.

Use eye protection2. . Always wear
ANSI-approved impact safety goggles
when assembling this product.

Stay alert3. . Watch what you are doing,
use common sense. Do not assemble
this product when you are tired.

Check for damaged parts4. . Before
using this product, any part that
appears damaged should be carefully
checked to determine that it will
operate properly and perform its
intended function. Check for loose

REV 07a

The warnings, cautions, and 7.
instructions discussed in this
instruction manual cannot cover all
possible conditions and situations that
may occur. It must be understood by
the operator that common sense and
caution are factors which cannot be
built into this product, but must be
supplied by the operator.

UNPACKING

When unpacking, make sure
the parts listed in the parts list at
the end of this manual are included.
If any parts are missing or broken,
please call Harbor Freight Tools at the
number on the cover of this manual.

Page 2For technical questions, please call 1-800-444-3353.SKU 91883

Top Pole Covers (1)

Bottom Shelf (3)

with Stand Feet (4).

Top Pole Covers (1)

Figure 1

Supporting Poles (2)

Stand Feet (4)

Between Shelves (3).

ASSEMBLY INSTRUCTIONS

Attach each Shelf (3) with the Supporting Poles (2) as shown in 1. Figure 1. It is

recommended that you start assembling bottom shelves rst and work upward.

On the bottom Shelf (3), push in the four Stand Feet (4).2. See Figure 1. Stand
Shelf Rack upright. Tap on the Top Pole Covers (1) in the holes in the top Shelf (3)

for a nished look. Check to see that the Shelf Rack is level.

CAUTION! Distribute weight evenly on shelves. Each shelf has a capacity of 44 lb.

maximum. Place Shelf Rack on a smooth, hard, level surface.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND
ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE
MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY
OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS
TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF
THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR
HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Page 3For technical questions, please call 1-800-444-3353.SKU 91883

PARTS LIST AND DIAGRAM

3

1

2

Part Description Qty.

1 Top Pole Cover 4
2 Supporting Pole 12
3 Shelf 4

4 Stand

4

Note: Some parts are listed and shown for

illustration purposes only, and are not
available individually as replacement parts.

4

LIMITED 90 DAY WARRANTY

Harbor Freight Tools Co. makes
every effort to assure that its products meet
high quality and durability standards, and
warrants to the original purchaser that this
product is free from defects in materials and
workmanship for the period of 90 days from
the date of purchase. This warranty does not
apply to damage due directly or indirectly, to
misuse, abuse, negligence or accidents, repairs
or alterations outside our facilities, criminal
activity, improper installation, normal wear and
tear, or to lack of maintenance. We shall in no
event be liable for death, injuries to persons
or property, or for incidental, contingent,
special or consequential damages arising from
the use of our product. Some states do not
allow the exclusion or limitation of incidental
or consequential damages, so the above
limitation of exclusion may not apply to you.
THIS WARRANTY IS EXPRESSLY IN LIEU OF
ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS.

To take advantage of this warranty,
the product or part must be returned to us
with transportation charges prepaid. Proof
of purchase date and an explanation of the
complaint must accompany the merchandise. If

our inspection veries the defect, we will either

repair or replace the product at our election or
we may elect to refund the purchase price if we
cannot readily and quickly provide you with a
replacement. We will return repaired products
at our expense, but if we determine there is no
defect, or that the defect resulted from causes
not within the scope of our warranty, then you
must bear the cost of returning the product.

This warranty gives you specic legal

rights and you may also have other rights which
vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009

Camarillo, CA 93011 • [phone]

Page 4For technical questions, please call 1-800-444-3353.SKU 91883