Page 1
WOODEN WINE RACK
ASSEMBLY INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
Copyright © 2004 by Harbor Freight Tools
®
.
All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or for m
without the express written consent of Harbor F reight T ools .
For technical questions and replacement parts, please call 1-800-444-3353
91734
®
Page 2
SKU 91734 For technical questions, please call 1-800-444-3353. Page 2
Specifications
Save This Manual
You will need the manual for the safety warnings and precautions, assembly
instructions, operating and maintenance procedures, parts list and diagram. K eep
your invoice with this manual. Write the invoice number on the inside of the front
cover. Keep the manual and in voice in a safe and dry place for future reference .
Safety Warnings and Precautions
WARNING: When using this product, basic safety precautions should alwa y s
be followed to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this product!
1. Keep work area clean. Cluttered areas invite injuries.
2. Keep children away. Do not let children play on or with this product.
3. Use eye and ear protection. Always wear ANSI approved impact safety
goggles when assembling this product. Goggles are available from Harbor
Freight Tools.
4. Do not overreach. Keep proper footing and balance at all times. Two or
more people are needed to assemble this product.
5. Use the right product for the job. There are certain applications for which
this product was designed. Do not modify this product and do not use this
product for a purpose for which it was not intended.
6. Stay alert. Watch what you are doing, use common sense. Do not assemble
this product when you are tired.
7. Check for damaged parts. Before using this product, any part that appears
damaged should be carefully checked to determine that it will operate
properly and perform its intended function. Check for loose parts and any
other condition that may affect the operation of this product. Replace loose
or worn parts immediately. Any part that is damaged should be properly
repaired or replaced.
8. Replacement parts. When servicing, use only identical replacement parts.
Use of any other parts will void the warranty.
Overall Dimensions
Holds Maximum Amount of Bottles
Materials
Weight
47-1/4” High X 28-1/4” Wide X 10-1/2” Deep
Qty. 28
Wood, Unfinished Pine
13 Lbs.
Page 3
SKU 91734 For technical questions, please call 1-800-444-3353. Page 3
9. Warning: Locate the Wine Rack in a spot that is flat without an uneven surface.
For safety reason, anchor Wine Rack to a wall in case of earthquake or another
disaster (hardware not provided).
10. Always distribute objects on Shelves evenly. Uneven weight distribution
could cause toppling. Harbor Freight Tools is not responsible for damage
or loss of bottles of wine due to an accident or an act of nature. Always
stack bottles from the bottom up.
Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may
occur. It must be understood by the operator that common sense and caution
are factors which cannot be built into this product, but must be supplied by the
operator.
Unpacking
When unpacking, check to make sure the following parts are included. If any parts
are missing or broken, please call Harbor Freight Tools at the number on the cover of
this manual.
Assembly Instructions
1. Starting with one side of the Side Wall (1), attach the Shelf (3) (with large
notches) using the Wood Screws (4) in the predrilled holes. That same shelf
attaches to the other Side Wall (1). Attach the remaining shelves. Note:
Shelves with large notches are designed to fit in the back of the rack.
2. Next, attach the Shelf (2) (small notches) on the facing Side Wall (1) (front
side). Repeat until all Shelves are assembled. Tighten all hardware. This
forms the 8 shelves for the wine bottles to rest upon.
(See Figures A & B).
2. Once assembled, stand the Wine Rack upright. Anchor the Wine Rack to
the wall to avoid tipping. (Hardware not included).
3. A varnish or stain may be applied after assembly. Avoid moisture on the
shelving unless you use a waterproof bar finish.
Figure A
Figure B
Shelf (3)
Shelf (2)
Side Wall (1)
Front of
Wine
Rack
Back of
Wine
Rack
Page 4
SKU 91734 For technical questions, please call 1-800-444-3353. Page 4
Parts List
Part # Description Qty.
1
2
3
4
2
8
8
32
Assembly Drawing
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO
REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THat ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES
ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR
REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACE-
MENT PARTS THERETO.
NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts.
Side Wall
Shelf (small notches)
Shelf (large notches)
Wood Screw
Part 1
Part 1
Part 3
Part 2
Part 4
Loading...