Page 1
1.5 Liter Pressurized Sprayer1.5 Liter Pressurized Sprayer
1.5 Liter Pressurized Sprayer1.5 Liter Pressurized Sprayer
1.5 Liter Pressurized Sprayer
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
Copyright © 2003 by Harbor Freight Tools®. All rights reserved. No portion of this manual or
any artwork contained herein may be reproduced in any shape or form without the express
written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
90189
90189 Sprayer.P65 10/9/03, 11:00 AM1
Page 2
SKU 90189 Page 2
Specifications
Save This Manual
You will need the manual for the safety warnings and precautions, assembly
instructions, operating and maintenance procedures, parts list and diagram. Keep
your invoice with this manual. Write the invoice number on the inside of the front
cover. Keep the manual and invoice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING: When using tool, basic safety precautions should always be followed
to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this tool!
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Do not use this tool in damp or wet
locations. Don’t expose to rain. Keep work area well lighted.
3. Keep children away. Children must never be allowed in the work area. Do
not let them handle this tool, or chemicals used with tool.
4. Store idle equipment. When not in use, tools must be stored in a dry
location to inhibit rust. Always lock up tools and keep out of reach of
children.
5. Use the right tool for the job. Do not attempt to force a small tool or
attachment to do the work of a larger industrial tool. There are certain
applications for which this tool was designed. It will do the job better
and more safely at the rate for which it was intended. Do not modify this
tool and do not use this tool for a purpose for which it was not intended.
6. Dress properly. Wear long sleeves, long pants and gloves when working with
chemical sprays. Do not wear loose clothing or jewelry as they can be caught in
moving parts. Protective, electrically nonconductive clothes and nonskid footwear
are recommended when working. Wear restrictive hair covering to contain long hair.
7. Use eye and ear protection. Always wear ANSI approved impact safety goggles.
Wear an ANSI approved dust mask or respirator when working around chemical
dusts and mists.
8. Do not overreach. Keep proper footing and balance at all times. Do not reach over or
across running machines.
9. Maintain tools with care. Keep tools clean for better and safer performance.
Follow instructions for lubricating and changing accessories. The handles
must be kept clean, dry, and free from oil and grease at all times.
90189 Sprayer.P65 10/9/03, 11:00 AM2
Page 3
SKU 90189 Page 3
10. Avoid unintentional starting. Do not carry any tool with your finger on the
trigger, whether it is pressurized or not.
11. Stay alert. Watch what you are doing, use common sense. Do not operate any
tool when you are tired.
12. Check for damaged parts. Before using any tool, any part that appears
damaged should be carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment and binding of moving
parts; any broken parts or mounting fixtures; and any other condition that may
affect proper operation. Any part that is damaged should be properly repaired or
replaced by a qualified technician. Do not use the tool if the trigger lever does
not turn On and Off properly.
13. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use
accessories intended for use with this tool. Approved accessories are available
from Harbor Freight Tools.
14. Do not operate tool if under the influence of alcohol or drugs. Read
warning labels on prescriptions to determine if your judgment or reflexes are
impaired while taking drugs. If there is any doubt, do not operate the tool.
15. WARNING: Never spray flammable liquids, such as gasolene or corrosive
agents from this sprayer.
Warning: The warnings, cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions and situations that may occur. It
must be understood by the operator that common sense and caution are factors
which cannot be built into this product, but must be supplied by the operator.
Unpacking
When unpacking, check to make sure the following parts are included.
(1) 1.5 Liter hand held sprayer
(1) Assembly Instructions/Parts List Diagram
If any parts are missing or broken, please call Harbor Freight Tools at the number on
the cover of this manual.
Operation
This sprayer is ideal for watering plants, fertilizing, applying cleaners, pesticides, etc.
It is easy to use, with a thumb lever control, and a hand pump to pressurize the tank.
It holds up to 1.5 liters of material. The Tank (3) is sturdy and washable.
NOTE: Always adhere to the dress properly recommendations discussed on page 2.
Clean the Tank (3) before and after use. If spraying a mixture, be sure the material
has been filtered to remove particles which may clog the spray nozzle.
90189 Sprayer.P65 10/9/03, 11:00 AM3
Page 4
SKU 90189 Page 4
Always read and adhere to all safety warnings provided by the manufacturer of any
chemical used with the Sprayer.
1. Unscrew the Handle (1) assembly from the Tank (3), and pour up to 1.5 liters
of water or prepared liquid mixture into the Tank (3).
2. Replace the Handle (1) assembly, and screw it tightly back into place. Be sure
that the seal is properly seated and that the tank is now air tight.
3. Place the sprayer upright on a firm surface. Do not hold the sprayer by the
Handle (1) while pumping, as this may damage the handle. Holding the
sprayer firmly, operate the Pump Handle (8) until the sprayer is pressurized.
When the pump becomes difficult to operate the sprayer is sufficiently
pressurized. WARNING: Do not over pressurize the sprayer, as this might
result in injury to persons or property.
4. Holding the sprayer by the Handle (1), spray by depressing the Trigger Lever
(11).
WARNING: Do not spray toward any person or animal. Protect yourself
from breathing or coming into contact with any pesticide or hazardous
material.
5. When finished spraying, point the orange Pressure Release Rod (12), located
on upper handle, away from you in a safe direction Release the pressure by
pulling the Orange Pressure Release Rod (12). Hold it out until the pressure
has completely released. WARNING: Do not unscrew the Handle (1) assembly
if the Tank (3) has not been de-pressurized.
6. Empty sprayer by unscrewing the Handle (1) assembly from the Tank (3). Pour
the material back into a suitable container, and wash the tank and sprayer
assembly. Clean the mechanism by spraying a small amount of clean water
through it.
Maintenance
1. Clean the sprayer before and after each use, using clean water or a suitable
detergent. Remember to spray a small amount of clean water through the
mechanism to clean it.
2. Protect the sprayer from heavy impacts or punctures which may be caused
by other tools. Store the sprayer safely when not in use.
WARNING: Never store hazardous materials in the sprayer when not in
use. This may damage the sprayer, and also may cause accidental
injury.
3. Do not store the sprayer in bright sunlight, as UV rays may damage the
plastic.
4. If you have difficulty pressurizing the sprayer, check the O rings to be sure
they are in position, and not damaged.
90189 Sprayer.P65 10/9/03, 11:00 AM4
Page 5
SKU 90189 Page 5
NOTE: Some parts are listed and shown for illustration purposes only and are not
available individually as replacement parts.
Parts List
1. Handle
2. Nut
3. 1.5 Liter Tank
5. Pump Housing
6. Pump Rod
7. Pump Cap
8. Pump Handle
9. Compression Ring
10. O ring 27mm
21. Jet Tube
22. Nut 10 x 1mm
23. O ring 8.8mm
24. O ring 62mm
25. Pipe Nipple
26. Spring 8.6 mm diameter
27. Spring 5.6mm diameter
28. Tube 4.1mm diameter
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER
NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO
THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE
PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE
PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THat ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS
OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
11. Trigger Lever
12. Pressure Release Rod
13. O ring 5mm
14. O ring
15. Flow Nipple
16. Valve
17. Small Ring
18. O ring
19. Sleeve Shut-off
20. Nut 18 x 1.5 mm
90189 Sprayer.P65 10/9/03, 11:00 AM5
Loading...