Harbor Freight Tools 69522 Product manual

Specifications

Weight Capacity 2,000 lb.

Face Plate 9-3/4" W x 5-7/8" H x 13/16" thick

Wheel Diameter 3"

Important Safety Information

Assembly Precautions

1. Assemble only according to these
instructions. Improper assembly
can create hazards.

2. Wear ANSI-approved safety goggles
and heavy-duty work gloves
during assembly.

3. Keep assembly area clean and well lit.

4. Keep bystanders out of the

5. Do not assemble when tired

6. Weight capacity and other product

Use Precautions

Failure to heed these instructions may result in
personal injury and/or property damage:

1. Study, understand, and follow all
instructions before operating this device.

2. Do not exceed rated capacity.
Be aware of dynamic loading!
Sudden load movement may
briefly create excess load
causing product failure.

3. Use only on hard, level surfaces.

4. Lock mounting plate rotating
mechanism before applying a load.

5. Assure load is centered and secured
to mounting attachments.

6. Only use when Legs are fully
extended outward and Eye Pins
and R-Pins are in place.

7. Hold Handle while removing the Pin.

8. Wear ANSI-approved safety goggles

9. Do not use for aircraft purposes.

10. Inspect before every use;

11. This product is not a toy. Do not allow

12. Use as intended only.

13. Maintain product labels and nameplates.

area during assembly.

or when under the influence
of drugs or medication.

capabilities apply to properly and
completely assembled product only.

and heavy-duty work gloves during use.

do not use if parts loose or damaged.

children to play with or near this item.

These carry important
safety information. If unreadable
or missing, contact Harbor Freight Tools
for a replacement.

Page 2 For technical questions, please call 1-800-444-3353. Item 69522

Assembly Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the
beginning of this document including all text under subheadings therein
before set up or use of this product.

1. Attach 3-1/2″ Casters (15) to the
straight, back section of the Base (8)
using Bolts (11), Spring Washers (10),
and Nuts (9). Insert Bolts from the
bottom, through the Casters first.

2. Attach 3″ Casters (16) to the angled,
front sections of the Base (8) using
Bolts (12), Spring Washers (10), and
Nuts (9). Insert Bolts from the top,
through the Base first.

Base (8)

3-1/2″

Caster

(15)

Bolt
(12)

3-1/2″

Caster

Legs

(17)

Leg Lock

Pins (13)

(15)

Figure B: Attach Legs

Note: There are five M14 diameter Bolts.

The longer one, part 4, is used to attach the
top of the two Braces (5) to the Column (2).

5. Attach Column (2) to Base (8) using
Bolts (3), Washers (7), and Nuts (6).

Leg Lock

Pins (13)

3-1/2″

Casters

(15)

3″ Caster

(16)

Bolt (11)

Figure A: Attach Casters to Base

3. Attach a 3-1/2” Caster (15) to the end
of each Leg (17) using Bolts (11),
Spring Washers (10), and Nuts (9).

4. Place Legs (17) into slots in Base (8)
with the Casters (15) turned downward.
Use two Leg Lock Pins (13) to
secure each Leg. Secure each
Leg Lock Pin using an R-pin (14).

Column (2)

Bolt (3)

Washer

(7)

Nut (6)

Figure C: Attach Column

Page 3For technical questions, please call 1-800-444-3353.Item 69522