Harbor Freight Tools 68422 Owner's Manual

1/6 HP Submersible Utility Pump

68422 Submersible Utility Pump

Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.

When unpacking, make sure that the product is intact and undamaged.

If any parts are missing or broken, please call 1-800-444-3353 as soon as possible.

Visit our website at: http://www.harborfreight.com

Copyright© 2011 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape

or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.

Before start-up, note the following:

The pump can be connected to any shock-proof plug
which has been installed according to regulations.
The plug must have a supply voltage of 120 V~ at 60 Hz.

CAUTION

This pump is intended for use with clean water.

WARNING

IMPORTANT! For your own safety –
before starting to run the pump, please have
the following items checked by an expert:

1. Risk of electric shock – This pump is supplied
with a grounding conductor and grounding-type
attachment plug. To reduce the risk of
electric shock, connect only to a properly
grounded, grounding-type receptacle.

2. Risk of electric shock – This pump has not been
investigated for use in swimming pool areas.

3. The electrical connections must be
protected from moisture. Do not

submerge power cord connection.

4. If there is danger of ooding, the electrical
connections must be taken to higher ground.

5. Circulation of caustic uids, as well as the circulation
of abrasive materials, must be avoided at all costs.

6. The pump must be protected from frost.

7. The pump must be protected from running dry.

Specications

Electrical Requirements 120V~ / 60Hz / 2.2 A

Motor 1/6 Horsepower Electric

Power Cord Length

Maximum Flow Rate 1350 GPH

Maximum Head Lift 23 FT.

Discharge Size 1 IN. NPT

Drains To 1/2 IN. of surface

10 FT. (Do not submerge beyond
power cord length. Do not
submerge power cord connection.)

252728

Installation

The submersible pump must be installed with either:

a. A xed pipeline or

b. A exible hose pipe.

Please note!

1. Do not install the pump by suspending it
unsupported from its delivery pipe or power cord.
The pump must be suspended from the handle
or be placed on the bottom of the area.

2. Make sure the Pump rests on at, level
and solid foundation. Do not operate it on
earth, clay, sand or gravel surfaces.

3. Make sure the Pump’s inlet openings near
the suction base are free of debris.

8. Access by children should also be
prevented with appropriate measures.

9. WARNING: Handling the Power Cord
on this product will expose you to lead,
a chemical known to the State of California
to cause cancer, and birth defects or other
reproductive harm. Wash hands after handling.
(California Health & Safety Code § 25249.5, et seq.)

10. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.

Fluid Type

The Pump is designed for use with water with
a maximum temperature of 77° F (25°C).

Do not use the pump for other uids, especially not
fuels, cleaning uids, or other chemical products.

4. Avoid installing Pump in areas
of extreme heat or cold.

Power Supply

1. The pump is equipped with a shock-proof plug
according to regulations. The pump is designed
to be connected to 120 V~, 60 Hz safety socket.

2. Make sure that the socket is sufciently
secured and is in excellent condition.

3. When the plug is inserted into the socket
the pump will start operating.

WARNING! If the power cord or plug is damaged,
do not use the pump. The power cord or plug

may only be repaired by a certied electrician.

Hose Connections

1. Use the included adaptor to connect a 5/8” or
larger hose to the pump outlet using a step
nipple and hose clamps (not included).

Page 2 For technical questions, please call 1-800-444-3353. SKU 68422

2. Route the hose to the desired discharge area. The
hose should be kept as short as possible with a
minimum number of turns. For best performance,
the max. recommended hose length is 50 ft.

3. To reduce vibration and noise, a short section
of rubber hose maybe be attached to the
end of the discharge line with clamps.

Areas of use

1. This pump can be used to transfer water
(e.g. household, farming, plumbing).

Operation

After reading these instructions,
consider the following points before starting the pump:

1. Verify that the pump rests on the oor of the shaft,
if it is not suspended by the handle.

2. Verify that the delivery pipe is properly connected.

3. Verify that the electrical connection is 120 V~, 60 Hz.

4. Verify that the electrical socket is in good condition.

5. Verify that water and moisture cannot get near the
power supply socket or power cord connection.

6. Verify that the pump is installed so as to
prevent running dry. NOTE: The Pump will
remove water down to 1/2”. Unplug the
Pump once 1/2” water level is reached.

7. If the pump is not going to be monitored
CONSTANTLY and disconnected when the
water level drops, it must be installed with an

automatic oat switch (not included) to shut it

off before it runs dry. CAUTION: Do not run
the Pump dry. Doing so will increase wear
on the unit and can lead to seal damage.

8. Plug power cord into an outlet protected by a GFCI.

Page 3For technical questions, please call 1-800-444-3353.SKU 68422