Harbor Freight Tools 68353 Owner's Manual
Solar Rope Light
Specications
Run Time up to 8 hours
Length 22’
Battery 1x ‘AA‘ NiCd
Item 68353
INSTRUCTIONS AND
PRECAUTIONS
Visit our website at:
http://www.harborfreight.com
Read this material before
using this product.
Failure to do so can result
in serious injury.
SAVE THIS MANUAL.
When unpacking, make sure
that the product is intact and
undamaged.
If any parts are missing or broken,
please call 1‑800‑444‑3353
as soon as possible.
Copyright© 2011 by Harbor Freight Tools®.
All rights reserved. No portion of this document
or any artwork contained herein may be
reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
Diagrams within this document may not be drawn
proportionally. Due to continuing improvements,
actual product may differ slightly from the
product described herein. Tools required for
installation and service may not be included.
For technical questions or replacement
parts, please call 1‑800‑444‑3353.
Important Safety Information
1. Verify that installation surface
has no hidden utility lines
before drilling, driving screws,
or digging to insert stake.
2. Place/mount the LED Rope
to prevent tripping or choking.
Keep out of reach of young
children and babies.
3. Install only according to
these instructions. Improper
installation can create hazards.
4. Wear ANSI‑approved safety
goggles and heavy‑duty work
gloves during installation.
5. Keep installation area
clean and well lit.
6. Keep bystanders out of the
area during installation.
7. Do not install when tired or
when under the inuence
of drugs or medication.
8. This product is not a toy.
Do not allow children to play
with or near this item.
9. Use as intended only.
10. CONTAINS NICKEL‑CADMIUM
BATTERY. BATTERY
MUST BE RECYCLED OR
DISPOSED OF PROPERLY.
Installation Instructions
Read the ENTIRE
IMPORTANT SAFETY
INFORMATION section
at the beginning of this
document including all
text under subheadings
therein before set up or
use of this product.
Selecting a Location
1. Select a mounting location that
will receive full sunlight as many
hours in the day as possible.
2. Even partial shade will greatly
hinder charging and therefore
limit operation time.
3. If the area has strong nighttime
light sources, these may prevent
the light from turning on at night,
or may cause it to icker instead
of turning on completely.
Wall Mounting
1. Select a wall location without
hidden cables or utility lines.
Turn off all power in the
wall for added safety.
2. Place the Wall Base (3) in
the desired location and mark
through the mounting holes.
3. Set the Wall Base aside
and drill holes in the marked
locations appropriate for
the Wall Anchors (5b).
4. Insert the Wall Anchors into the
holes, align the holes in the Base
with the Anchors, and secure it in
place with the Wall Screws (5a).
5. Attach the Panel Connector (2)
to the Wall Base (3).
6. Attach the Solar Panel (1) to the
slots on the Panel Connector.
Stake Mounting
1. Select a ground location
to insert the Stake (6).
2. Make sure that there are no hidden
obstacles or utility lines in the area.
3. If the ground is too hard to
insert the stake, dig a hole
large enough for the stake, rell
the hole, and slightly pack the
ground to give some support.
4. Insert the Stake into the hole.
5. Attach the Stake Connector (4)
onto the top of the Stake.
6. Attach the Panel Connector (2) to
the top of the Stake Connector.
7. Attach the Solar Panel (1) to the
slots on the Panel Connector.
LED Rope Mounting
1. The LED Rope (1) can be left loose,
or can be mounted to an object.
2. Place/mount the LED Rope
to prevent tripping or choking.
Keep out of reach of young
children and babies.
3. If wall mounting, select a
location without hidden cables
or utility lines. Also, turn off all
power in the wall for safety.
Page 2 For technical questions, please call 1‑800‑444‑3353. SKU 68353
Loading...