ELECTRIC HAMMER
Model
68147
SET UP AND OPERATING INSTRUCTIONS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright© 2010 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1‑800‑444‑3353.
SAVE THIS MANUAL
Keep this manual for the safety
warnings and precautions, assembly,
operating, inspection, maintenance and
cleaning procedures. Write the product’s
serial number in the back of the manual
near the assembly diagram (or month and
year of purchase if product has no number).
Keep this manual and the receipt in a
safe and dry place for future reference.
IMPORTANT SAFETY
INFORMATION
In this manual, on the labeling,
and all other information
provided with this product:
This is the safety alert
symbol. It is used to alert
you to potential personal
injury hazards. Obey all
safety messages that
follow this symbol to avoid
possible injury or death.
DANGER indicates a
hazardous situation
which, if not avoided, will result
in death or serious injury.
WARNING indicates a
hazardous situation
which, if not avoided, could
result in death or serious injury.
CAUTION, used with
the safety alert
symbol, indicates a hazardous
situation which, if not avoided,
could result in minor or
moderate injury.
NOTICE is used to
address practices not
related to personal injury.
CAUTION, without the
safety alert symbol, is
used to address practices not
related to personal injury.
General Power Tool Safety Warnings
WARNING Read all safety warnings
and instructions. Failure to follow
the warnings and instructions may
result in electric shock, re and/or
serious injury.
Save all warnings and instructions
for future reference.
The term ″power tool″ in the warnings
refers to your mains-operated
(corded) power tool or batteryoperated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b. Do not operate power tools in
explosive atmospheres, such
as in the presence of ammable
liquids, gases or dust. Power
tools create sparks which may
ignite the dust or fumes.
c. Keep children and bystanders
away while operating a
power tool. Distractions can
cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the
outlet. Never modify the plug in
any way. Do not use any adapter
plugs with grounded power tools.
Unmodied plugs and matching outlets
will reduce risk of electric shock.
b. Do not expose power tools to
rain or wet conditions. Water
Page 2 For technical questions, please call 1‑800‑444‑3353. SKU 68147
entering a power tool will increase
the risk of electric shock.
c. Do not abuse the cord. Never
use the cord for carrying, pulling
or unplugging the power tool.
Keep cord away from heat, oil,
sharp edges or moving parts.
Damaged or entangled cords
increase the risk of electric shock.
d. When operating a power tool
outdoors, use an extension cord
suitable for outdoor use. Use
of a cord suitable for outdoor use
reduces the risk of electric shock.
e. If operating a power tool in a damp
location is unavoidable, use a
Ground Fault Circuit Interrupter
(GFCI) protected supply. Use of a
GFCI reduces the risk of electric shock.
d. Do not overreach. Keep proper
footing and balance at all times.
This enables better control of the
power tool in unexpected situations.
e. Dress properly. Do not wear
loose clothing or jewelry. Keep
your hair, clothing and gloves
away from moving parts. Loose
clothes, jewelry or long hair can
be caught in moving parts.
f. Only use safety equipment that has
been approved by an appropriate
standards agency. Unapproved
safety equipment may not provide
adequate protection. Eye protection
must be ANSI-approved and breathing
protection must be NIOSH-approved for
the specic hazards in the work area.
4. Power tool use and care
3. Personal safety
a. Stay alert, watch what you are
doing and use common sense when
operating a power tool. Do not use
a power tool while you are tired
or under the inuence of drugs,
alcohol or medication. A moment of
inattention while operating power tools
may result in serious personal injury.
b. Use personal protective equipment.
Always wear eye protection. Safety
equipment such as dust mask, non-
skid safety shoes, hard hat, or hearing
protection used for appropriate
conditions will reduce personal injuries.
c. Prevent unintentional starting.
Ensure the switch is in the off‑
position before connecting to power
source and/or battery pack, picking
up or carrying the tool. Carrying
power tools with your nger on the
switch or energizing power tools that
have the switch on invites accidents.
a. Do not force the power tool. Use
the correct power tool for your
application. The correct power tool
will do the job better and safer at
the rate for which it was designed.
b. Do not use the power tool if the
switch does not turn it on and
off. Any power tool that cannot
be controlled with the switch is
dangerous and must be repaired.
c. Disconnect the plug from the
power source and/or the battery
pack from the power tool before
making any adjustments, changing
accessories, or storing power
tools. Such preventive safety
measures reduce the risk of starting
the power tool accidentally.
d. Store idle power tools out of
the reach of children and do
not allow persons unfamiliar
with the power tool or these
instructions to operate the power
tool. Power tools are dangerous
in the hands of untrained users.
Page 3For technical questions, please call 1‑800‑444‑3353.SKU 68147
e. Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any
other condition that may affect the
power tool’s operation. If damaged,
have the power tool repaired before
use. Many accidents are caused
by poorly maintained power tools.
f. Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely
to bind and are easier to control.
g. Use the power tool, accessories
and tool bits etc. in accordance
with these instructions, taking into
account the working conditions
and the work to be performed.
Use of the power tool for operations
different from those intended could
result in a hazardous situation.
5. Service
5. Unplug before inspecting,
removing or installing chisel,
or performing any service.
6. Pull on chisel after installation
and before use; chisel may move
but MUST NOT slide out.
7. Wear steel-toed boots during use.
8. Do not operate this tool if you have
back, neck, or wrist injuries, or other
conditions that will be aggravated
by the severe jerking forces that this
tool exerts upon the operator.
9. Maintain labels and nameplates
on the tool. These carry important
safety information. If unreadable
or missing, contact Harbor Freight
Tools for a replacement.
10. Avoid unintentional starting. Prepare to
begin work before turning on the tool.
a. Have your power tool serviced by
a qualied repair person using
only identical replacement parts.
This will ensure that the safety of
the power tool is maintained.
Breaker Hammer Safety Warnings
1. Wear ear protectors. Exposure to
noise can cause hearing loss.
2. Use auxiliary handles supplied
with the tool. Loss of control
can cause personal injury.
3. Hold power tools by insulated
gripping surfaces when performing
an operation where the cutting tool
may contact hidden wiring or its
own cord. Contact with a ″live″ wire
will make exposed metal parts of the
tool ″live″ and shock the operator.
4. Keep clear of moving parts.
11. Do not lay the tool down until it has
come to a complete stop. Moving
parts can grab the surface and
pull the tool out of your control.
12. When using a handheld power tool,
maintain a rm grip on the tool with
both hands to resist starting torque.
13. Do not leave the tool unattended when
it is plugged into an electrical outlet.
Turn off the tool, and unplug it from
its electrical outlet before leaving.
14. This product is not a toy. Keep
it out of reach of children.
15. People with pacemakers should
consult their physician(s) before use.
Electromagnetic elds in close proximity
to heart pacemaker could cause
pacemaker interference or pacemaker
failure. In addition, people with
pacemakers should:
• Avoid operating alone.
Page 4 For technical questions, please call 1‑800‑444‑3353. SKU 68147
• Properly maintain and inspect to avoid
electrical shock.
• Any power cord must be properly
grounded. Ground Fault Circuit
Interrupter (GFCI) should also
be implemented – it prevents
sustained electrical shock.
16. WARNING: Some dust created by power
sanding, sawing, grinding, drilling, and
other construction activities, contains
chemicals known [to the State of
California] to cause cancer, birth defects
or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and
cement or other masonry products
• Arsenic and chromium from chemically
treated lumber
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to
these chemicals: work in a well ventilated
area, and work with approved safety
equipment, such as those dust masks
that are specially designed to lter out
microscopic particles. (California Health
& Safety Code § 25249.5, et seq.)
17. WARNING: Handling the cord on this
product will expose you to lead, a
chemical known to the State of California
to cause cancer, and birth defects or
other reproductive harm. Wash hands
after handling. (California Health &
Safety Code § 25249.5, et seq.)
Vibration Safety
This tool vibrates during use. Repeated
or long-term exposure to vibration
may cause temporary or permanent
physical injury, particularly to the
hands, arms and shoulders. To reduce
the risk of vibration-related injury:
1. Anyone using vibrating tools regularly
or for an extended period should rst
be examined by a doctor and then
have regular medical check-ups to
ensure medical problems are not
being caused or worsened from use.
Pregnant women or people who have
impaired blood circulation to the hand,
past hand injuries, nervous system
disorders, diabetes, or Raynaud’s
Disease should not use this tool. If
you feel any symptoms related to
vibration (such as tingling, numbness,
and white or blue ngers), seek
medical advice as soon as possible.
2. Do not smoke during use. Nicotine
reduces the blood supply to the
hands and ngers, increasing the
risk of vibration-related injury.
3. Wear suitable gloves to reduce the
vibration effects on the user.
4. Use tools with the lowest vibration
when there is a choice.
5. Include vibration-free periods
each day of work.
18. The warnings, precautions, and
instructions discussed in this instruction
manual cannot cover all possible
conditions and situations that may
occur. It must be understood by the
operator that common sense and
caution are factors which cannot
be built into this product, but must
be supplied by the operator.
6. Let the tool do the work.
7. To reduce vibration, maintain
the tool as explained in this
manual. If any abnormal vibration
occurs, stop use immediately.
SAVE THESE
INSTRUCTIONS.
Page 5For technical questions, please call 1‑800‑444‑3353.SKU 68147
GROUNDING
TO PREVENT
ELECTRIC SHOCK
AND DEATH FROM INCORRECT
GROUNDING WIRE
CONNECTION:
Check with a qualied electrician
if you are in doubt as to whether
the outlet is properly grounded.
Do not modify the power cord
plug provided with the tool.
Never remove the grounding
prong from the plug. Do not use
the tool if the power cord or plug
is damaged. If damaged, have it
repaired by a service facility
before use. If the plug will not
t the outlet, have a proper
outlet installed by a
qualied electrician.
Double Insulated Tools: Tools
with Two Prong Plugs
preceding illustration.
(See Outlets for 2‑Prong Plug.)
Extension Cords
1. Grounded tools require a three
wire extension cord. Double
Insulated tools can use either a
two or three wire extension cord.
2. As the distance from the supply outlet
increases, you must use a heavier gauge
extension cord. Using extension cords
with inadequately sized wire causes a
serious drop in voltage, resulting in loss
of power and possible tool damage.
(See Table A.)
3. The smaller the gauge number of
the wire, the greater the capacity of
the cord. For example, a 14 gauge
cord can carry a higher current than
a 16 gauge cord. (See Table A.)
4. When using more than one
extension cord to make up the
total length, make sure each cord
contains at least the minimum wire
size required. (See Table A.)
5. If you are using one extension
cord for more than one tool, add
the nameplate amperes and use
the sum to determine the required
minimum cord size. (See Table A.)
Outlets for 2‑Prong Plug
6. If you are using an extension cord
1. Tools marked “Double Insulated” do
not require grounding. They have a
special double insulation system which
satises OSHA requirements and
complies with the applicable standards
of Underwriters Laboratories, Inc.,
the Canadian Standard Association,
and the National Electrical Code.
2. Double insulated tools may be used in
either of the 120 volt outlets shown in the
Page 6 For technical questions, please call 1‑800‑444‑3353. SKU 68147
outdoors, make sure it is marked with
the sufx “W-A” (“W” in Canada) to
indicate it is acceptable for outdoor use.
7. Make sure the extension cord is
properly wired and in good electrical
condition. Always replace a damaged
extension cord or have it repaired by
a qualied electrician before using it.
8. Protect the extension cords from
sharp objects, excessive heat,
and damp or wet areas.
RECOMMENDED MINIMUM WIRE GAUGE
FOR EXTENSION CORDS* (120/240 VOLT)
NAMEPLATE
AMPERES
(at full load)
0 – 2.0 18 18 18 18 16
2.1 – 3.4 18 18 18 16 14
3.5 – 5.0 18 18 16 14 12
5.1 – 7.0 18 16 14 12 12
7.1 – 12.0 18 14 12 10 -
12.1 – 16.0 14 12 10 - -
16.1 – 20.0 12 10 - - -
TABLE A
EXTENSION CORD
LENGTH
25’ 50’ 75’ 100’ 150’
* Based on limiting the line volt‑
age drop to ve volts at 150% of
the rated amperes.
V~
A
n0 xxxx/min.
Symbology
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
Volts Alternating Current
Amperes
No Load Revolutions
per Minute (RPM)
Page 7For technical questions, please call 1‑800‑444‑3353.SKU 68147
SPECIFICATIONS
Functions
Electrical
Input
Blows Per
Minute
Chisel 1 Bull Point (included)
Weight 71 lb.
Other
Accessories
120 V~ / 60 Hz / 15 A
950 BPM
1 Oil Bottle
1 Carbon Brush Set
1 Flat Chisel
4 Hex Keys (5mm, 6mm, 8mm, 12mm)
1 Oil Tank Wrench
E252823
UNPACKING
When unpacking, make sure the item
is intact and undamaged. If any parts are
missing or broken, please call Harbor Freight
Tools at 1-800-444-3353 as soon as possible.
Use Figure 1 below as reference
during Tool Setup and Operation.
Fan Cover (10)
Side Handle
(31A)
Housing (1)
Switch Lock
Pin (84)
Aluminum
Casing (60)
Switch Trigger
(82)
Main Handle
(86)
INSTRUCTIONS FOR
PUTTING INTO USE
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
Note: For additional information regarding
the parts listed in the following pages,
refer to the Assembly Diagram
near the end of this manual.
Front
Cover (75)
Lock
Lever (74)
Figure 1
Page 8 For technical questions, please call 1‑800‑444‑3353. SKU 68147
OPERATING INSTRUCTIONS
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
3. Insert the shank portion of the chisel into
Front Cover (75). See Figure 2, below.
Chisel
Work Piece and Work Area Set Up
1. Designate a work area that is clean
and well-lit. The work area must
not allow access by children or pets
to prevent distraction and injury.
2. Route the power cord along a safe
route to reach the work area without
creating a tripping hazard or exposing
the power cord to possible damage.
The power cord must reach the work
area with enough extra length to
allow free movement while working.
3. Secure loose work pieces using
a vise or clamps (not included) to
prevent movement while working.
4. There must not be objects, such as
utility lines, nearby that will present
a hazard while working. If working in
the ground or on a concrete slabe on
the earth, call local utility company to
ensure that area is clear of utility lines.
Lock
Lever (74)
Figure 2
Front
Cover (75)
4. Turn Lock Lever back to original
position, locking chisel into place.
Pull chisel to verify it is secure.
General Operating Instructions
1. Set the bit against the work area.
2. Place one hand on the Side
Handle (31A) and the other hand
around the Main Handle (86).
3. Press the Switch Lock Pin (84)
and then push down on the Switch
Trigger (82). See Figure 3, below.
Switch Trigger
(82)
Mounting Tool Bits
1. WARNING! Before installing new
bit, unplug Electric Hammer.
2. Turn Lock Lever (74) 180° and slide out.
Switch Lock
Pin (84)
Figure 3
Main Handle
(86)
4. Push the tip forcibly down in order
to begin striking material.
5. WARNING! Once activated, do not
press, bear down or thrust forcibly
Page 9For technical questions, please call 1‑800‑444‑3353.SKU 68147
against the work surface. Hold the
Electric Hammer with just enough
pressure so that the tool’s own
weight supplies the needed force.
6. NOTE: If the Electric Hammer has not
been used for a long period of time
or is being used in low temperatures,
keep the tool running for about ve
minutes to allow for warm-up.
7. When work is complete, release
the Switch Trigger. The Switch
Lock will automatically activate.
8. To prevent accidents, turn off the
tool and disconnect its power supply
after use. Clean, then store the tool
indoors out of children’s reach.
MAINTENANCE AND
SERVICING
Procedures not specically
explained in this manual
must be performed only by
a qualied technician.
Maintenance, and Lubrication
1. BEFORE EACH USE, inspect the
general condition of the tool. Check
for loose hardware, misalignment
or binding of moving parts, cracked
or broken parts, damaged electrical
wiring, and any other condition that
may affect its safe operation.
2. AFTER USE, wipe external surfaces
of the tool with clean cloth.
3. Wipe tool with lint-free cloth after each
use to remove all dust and grit from tool.
NOTE: The Breaker Hammer has an
air‑tight construction, allowing
for six months of continuous
usage before any additional
lubrication is needed.
4. To add lubricating grease, the Tank
Cover Wrench (105) to open the Tank
Cover (48). See Figure 4, below.
Oil Tank Cover (48)
Oil Hole
NOTE: The Breaker Hammer will cease
operation once Carbon Brushes are
worn. Check Brushes every 100
hours and replace when necessary.
TO PREVENT
SERIOUS INJURY
FROM ACCIDENTAL
OPERATION: Release Trigger and
unplug the tool from its electrical
outlet before performing any
inspection, maintenance, or
cleaning procedures.
TO PREVENT SERIOUS INJURY
FROM TOOL FAILURE:
Do not use damaged equipment.
If abnormal noise or vibration
occurs, have the problem
corrected before further use.
Figure 4
5. Fill with 2 ounces of lubricating grease.
6. Replace Tank Cover,
tightening until secure.
7. Examine the tool before each use. Make
sure the Chisel is sharp and not dull
or cracked. Replace worn or broken
Page 10 For technical questions, please call 1‑800‑444‑3353. SKU 68147
Chisels with approved replacement
Chisels from Harbor Freight Tools.
8. Check that all mounting screws are
tightened. Retighten any loose screws.
9. Store in temperatures no
lower than 50-60° F.
10. WARNING! If the supply cord of
this power tool is damaged, it must
be replaced only by a qualied
service technician.
4. Remove old Carbon Brush (6).
5. Insert new Carbon Brush.
6. Replace Carbon Brush Cap and slide
Fan Cover back over Housing.
7. Replace Hex Bolts and Flat
Washers until securely fastened.
8. WARNING! Verify all bolts and
connectors are fastened tight.
Cleaning
Replacing Carbon Brushes
NOTE: The Breaker Hammer will cease
operation once Carbon Brushes are
worn. Check Brushes every 100‑120
hours and replace when necessary.
1. Remove the Fan Cover (10) by
loosening the Hex Bolt (12) and Flat
Washers (11). See Figure 5, below.
2. Slide Fan Cover off of Housing (1).
3. Remove Brush Cap (5) from Housing.
Housing (1)
Carbon Brush (6)
Brush Cap (5)
1. Clean the Electric Hammer with
warm water, soap a soft cloth,
preferably after each use.
2. WARNING! Do not use solvents
when cleaning the Electric Hammer.
Doing so can damage the tool.
Carbon
Brush Holder (7)
Fan Cover (10)
Figure 5
Hex Bolt
(12)
Flat
Washer
(11)
Page 11For technical questions, please call 1‑800‑444‑3353.SKU 68147
Troubleshooting
Problem Possible Causes Likely Solutions
Tool will not start. 1. Cord not connected.
2. No power at outlet.
3. Tool’s thermal reset breaker
tripped (if equipped).
4. Internal damage or
wear. (Carbon brushes or
switch, for example.)
Tool operates slowly. Extension cord too long or
wire size too small.
Performance
decreases over time.
Excessive noise
or rattling.
Overheating. 1. Forcing tool to work too fast.
1. Accessory dull or damaged.
2. Internal lubrication cold.
3. Carbon brushes worn
or damaged.
Internal damage or wear. (Carbon
brushes or bearings, for example.)
2. Accessory dull or damaged.
3. Blocked motor housing vents.
4. Motor being strained by long or
small diameter extension cord.
1. Check that cord is plugged in.
2. Check power at outlet. If outlet is unpowered,
turn off tool and check circuit breaker. If breaker
is tripped, make sure circuit is right capacity
for tool and circuit has no other loads.
3. Turn off tool and allow to cool.
Press reset button on tool.
4. Have technician service tool.
Eliminate use of extension cord. If an extension
cord is needed, use shorter/heavier gauge cord.
See Extension Cords in GROUNDING section.
1. Keep cutting accessories sharp.
Replace as needed.
2. Allow tool to operate with no load
for 5 minutes before use.
3. Have qualied technician replace brushes.
Have technician service tool.
1. Allow tool to work at its own rate.
2. Keep cutting accessories sharp.
Replace as needed.
3. Wear ANSI-approved safety goggles and NIOSH-
approved dust mask/respirator while blowing
dust out of motor using compressed air.
4. Eliminate use of extension cord. If an
extension cord is needed, use one with the
proper diameter for its length and load. See
Extension Cords in GROUNDING section.
Follow all safety precautions whenever diagnosing or servicing
the tool. Disconnect power supply before service.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES
ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO
MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT
ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT
OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Page 12 For technical questions, please call 1‑800‑444‑3353. SKU 68147
LIMITED 90 DAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality
and durability standards, and warrants to the original purchaser that this product is free from
defects in materials and workmanship for the period of 90 days from the date of purchase. This
warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or
accidents, repairs or alterations outside our facilities, criminal activity, improper installation,
normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,
injuries to persons or property, or for incidental, contingent, special or consequential damages
arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to
you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the complaint
must accompany the merchandise. If our inspection veries the defect, we will either repair
or replace the product at our election or we may elect to refund the purchase price if we
cannot readily and quickly provide you with a replacement. We will return repaired products
at our expense, but if we determine there is no defect, or that the defect resulted from causes
not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specic legal rights and you may
also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
Page 13For technical questions, please call 1‑800‑444‑3353.SKU 68147
PARTS LIST
Part Description Qty
1 Housing 1
2 End Cover 1
3 Hex Socket Bolt
(M10X35)
4 Flat Washer (Ø10) 14
5 Brush Cap 2
6 Carbon Brush 2
7 Brush Holder 2
8 Insulating Washer 2
9 Cap 2
10 Fan Cover 1
11 Flat Washer (Ø6) 6
12 Hex Socket Bolt
(M6X20)
13 Urethane Washer
(Ø32)
14 Ball Bearing
(6201 2RS C3)
15 Stator Housing 1
16 Circuit 1
17 Stator 1
19
Flat Washer (Ø5)
20 Screw (ST4.8X80) 2
21
Armature
22 Inner Cover 1
22A O-Ring (143X2) 1
23 Hex Socket Bolt
(M10X30)
24 Ball Bearing
(6203 2RS C3)
25 Bearing Plate 1
26 Hex Socket
Bolt (M5X12)
27 Needle Bearing
(BK1312)
28 Counter Gear 1
29 Bearing Cover
(6201 2RZ C2)
30 Gear Cover 1
31 Side Handle Shaft 1
31A Side Handle Protector 1
31B Side Handle Cap 1
32
Flat Washer (Ø8)
33
Spring Washer (Ø8)
4
8
1
2
3
1
2
1
7
1
1
4
4
Part Description Qty
34 Hex Socket
Bolt (M8X30)
35 Socket Bolt (M10X55) 4
36 Ball Bearing
6204 2RZ/ZZC2
37 Partition Washer 1
38 Gear 1
39 Distance Ring 1
40 Pin (Ø8x14) 2
41 Ball Bearing
6305 2RZ/ZZ C2
42 Oil Seal Ring
(Ø34XØ48X5)
43 Bearing Cover 1
44 Key (4X18) 2
45 Crank Shaft 1
46 Crank Shaft Ring 1
47 O-Ring (Ø37XØ2) 2
48 Oil Tank Cover 2
49 Hex Socket Bolt
(M10X1.25X35)
50 Crank Washer 1
51 Needle Bearing
(NK2220)
52 Connecting Rod 1
53 Piston Pin 1
54 Sealing Ring
(Ø45.7XØ55.2X7)
55 Piston 1
56 O-Ring (Ø46XØ5.3) 1
57 Cylinder 1
58 O-Ring (Ø82XØ2) 1
59 Hex Socket Bolt
(M10X45)
60 Aluminum Casing 1
61 Washer 1
61A Ring Support 1
62 Ring 1
63 Bushing 1
65 Locking Ring 1
66 Small Ring 1
67 Shank Sleeve 1
68 O-Ring (Ø36XØ5.5) 1
69 O-Ring (Ø78XØ3) 1
4
1
1
1
1
1
1
4
Part Description Qty
70 Impact Hammer 1
71 O-Ring (Ø55XØ5.3) 1
72 O-Ring (Ø90XØ2) 1
73 Hex Socket Bolt
(M14X40)
74 Locking Lever 1
75 Front Cover 1
76 Lever Spring 1
77 Locking Lever Cover 1
78 Spring Cover 1
79 Needle Roller 1
80 Main Handle Cover 1
81 Retaining Ring (Ø5) 1
82 Switch Trigger 1
83 Pin Spring 1
84 Switch Lock Pin 1
85 Shaft Pin 1
86 Main Handle 1
87 Switch Bracket 2
88 Wire Cover 1
89 Screw (ST4.2X18) 6
90 Hex Socket Bolt
(M6X15)
91 Flat Washer
(Ø6XØ18)
92 Handle Support 1
93 Spring Washer (Ø6) 2
94 Capacitor 1
95 Rivet 2
96 Switch 1
97 Cord Clip 1
98 Spring Pole 4
99 Cord Protector 1
100 Cord 1
101 Hex Wrench (5mm) 1
102 Hex Wrench (6mm) 1
103 Hex Wrench (8mm) 1
104 Hex Wrench (12mm) 1
105 Tank Cover Wrench 1
108 Oil Bottle 1
109 Fan Guide 1
4
4
2
Page 14 For technical questions, please call 1‑800‑444‑3353. SKU 68147
ASSEMBLY DIAGRAM
Page 15For technical questions, please call 1‑800‑444‑3353.SKU 68147
Loading...