Rated Single
Line Pull
ApplicationVehicle Recovery / For
Motor12VDC 5.1 HP Series Wound
Power IN &
Power OUT
Duty Cycle Rating5% (45 sec at Max Rated Load;
Pendant ControllerWired, 12 ft (3.7m) long
Geartrain3-Stage Planetary
Gear Ratio218:1
FreespoolSliding Ring Gear
BrakeAuto. Load Holding
Drum (Dia. X L)2.5″ X 5.3″ (64mm X 134mm)
Clevis Hook5/16″, Replaceable with
FairleadRoller with nylon bushings
Overload ProtectionIn line Circuit Breaker
Sound Rating85 dB
Rated Single
Line Pull
ApplicationVehicle Recovery / For
Motor12VDC 5.5 HP Series Wound
Power IN &
Power OUT
Duty Cycle Rating5% (45 sec at Max Rated Load;
Pendant ControllerWired, 12 ft (3.7m) long
Geartrain3-Stage Planetary
Gear Ratio218:1
FreespoolSliding Ring Gear
BrakeAuto. Load Holding
Drum (Dia. X L)2.5″ X 8.8″ (64mm X 224mm)
Clevis Hook3/8″, Replaceable with
FairleadRoller with nylon bushings
Overload ProtectionIn line Circuit Breaker
Sound Rating85 dB
Rated Single
Line Pull
ApplicationVehicle Recovery / For
Motor12VDC 6 HP Series Wound
Power IN &
Power OUT
Duty Cycle Rating5% (45 sec at Max Rated Load;
Pendant ControllerWired, 12 ft (3.7m) long
Geartrain3-Stage Planetary
Gear Ratio265:1
FreespoolSliding Ring Gear
BrakeAuto. Load Holding
Drum (Dia. X L)2.5″ X 8.8″ (64mm X 224mm)
Clevis Hook3/8″, Replaceable with
FairleadRoller with nylon bushings
Overload ProtectionIn line Circuit Breaker
Sound Rating85 dB
Keep this manual for the safety warnings and precautions,
assembly, operating, inspection, maintenance and
cleaning procedures. Write the product’s serial
number in the back of the manual near the assembly
diagram (or month and year of purchase if product
has no number). Keep this manual and the receipt
in a safe and dry place for future reference.
Important Safety Information
Symbol Definitions
In this manual, on the labeling, and all other
information provided with this product:
This is the safety alert symbol.
It is used to alert you to potential
personal injury hazards.
Obey all safety messages that follow this
symbol to avoid possible injury or death.
DANGER indicates a hazardous situation which, if
not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation which, if
not avoided, could result in death or serious injury.
CAUTION, used with the safety alert symbol,
indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE is used to address practices
not related to personal injury.
CAUTION, without the safety alert symbol, is used
to address practices not related to personal injury.
Wear heavy-duty, cut- and
abrasion-resistant leather gloves.
Wear ANSI-approved safety glasses.
Cut or sever hazard.
Roller entanglement hazard.
Hot surface burn hazard.
Fire hazard.
Caustic chemical (acid) hazard.
VDC
A
CCA
HP
fpm
mpm
Use winch only in underwind orientation.
(Wire rope enters/exits at the bottom.)
Volts Direct Current
Amperes
Cold Cranking Amperes
Horsepower
Feet Per Minute
Meters Per Minute
Explosion hazard.
Do not loop the wire rope around
object and hook onto itself.
Do not place finger(s) through hook.
Fingers may be caught and get
pulled into fairlead or drum.
Pull hook using strap only.
Do not use winch in overwind orientation.
(Wire rope enters/exits at the top.)
RPM
IP
G8
Revolutions Per Minute
International Protection rating
Classifies the degrees of protection provided
against the intrusion of solid objects,
dust, accidental contact, and water.
Grade 8
A fastener strength rating.
WARNING! Read all instructions.
Failure to follow all instructions listed on
pages 7 to 10 may result in fire, serious
injury and/or DEATH.
The warnings and precautions discussed in this
manual cannot cover all possible conditions and
situations that may occur. It must be understood
by the operator that common sense and caution
are factors which cannot be built into this
product, but must be supplied by the operator.