Harbor Freight Tools 68012 Product manual

Owner’s Manual & Safety Instructions

Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating,

inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual
near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and
the receipt in a safe and dry place for future reference.

12 VOLT LITHIUM-ION

OSCILLATING

MULTIFUNCTION

POWER TOOL

Visit our website at: http://www.harborfreight.com

REV 14h

When unpacking, make sure that the product is intact

and undamaged. If any parts are missing or broken,

please call 1-888-866-5797 as soon as possible.

Copyright© 2010 by Harbor Freight Tools®. All rights reserved.

No portion of this manual or any artwork contained herein may be reproduced in

any shape or form without the express written consent of Harbor Freight Tools.

Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein.

Tools required for assembly and service may not be included.

Email our technical support at: [e-mail]

Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.

Table of Contents

Safety ......................................................... 2

Specifications ............................................. 7

Setup .......................................................... 7

SAFETY OPERATION MAINTENANCESETUP

Operation .................................................... 8

This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

Maintenance .............................................. 10

Parts List and Diagram .............................. 11

Warranty .................................................... 12

WARNING SYMBOLS AND DEFINITIONS

Obey all safety messages that follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Addresses practices not related to personal injury.

IMPORTANT SAFETY INFORMATION

General Power Tool Safety Warnings

Read all safety warnings and instructions.

Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term ″power tool″ in the warnings refers to your battery-operated (cordless) power tool.

Work area safety

1. Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

2. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or fumes.

3. Keep children and bystanders
away while operating a power tool.

Distractions can cause you to lose control.

Page 2 For technical questions, please call 1-888-866-5797. Item 68012

Electrical safety

Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric shock.

Personal safety

1. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the influence of drugs, alcohol or
medication. A moment of inattention while operating

power tools may result in serious personal injury.

2. Use personal protective equipment. Always wear
eye protection. Safety equipment such as

dust mask, non-skid safety shoes, hard hat,

or hearing protection used for appropriate
conditions will reduce personal injuries.

3. Prevent unintentional starting.
Ensure the Power Switch is in the off-position
before connecting to power source, picking up or
carrying the tool.

Carrying power tools with your finger on the
Power Switch or energizing power tools that

have the Power Switch on invites accidents.

4. Remove any adjusting key or wrench
before turning the power tool on.

A wrench or a key left attached to a rotating part
of the power tool may result in personal injury.

5. Do not overreach. Keep proper footing and
balance at all times. This enables better control

of the power tool in unexpected situations.

6. Dress properly. Do not wear loose clothing or
jewelry. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewelry

or long hair can be caught in moving parts.

7. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of

these devices can reduce dust-related hazards.

8. Only use safety equipment that has been
approved by an appropriate standards agency.

Unapproved safety equipment may not provide
adequate protection. Eye protection must be
ANSI-approved and breathing protection
must be NIOSH-approved for the
specific hazards in the work area.

SAFETYOPERATIONMAINTENANCE SETUP

Power tool use and care

1. Do not force the power tool. Use the
correct power tool for your application.

The correct power tool will do the job better and

safer at the rate for which it was designed.

2. Do not use the power tool if the Power Switch
does not turn it on and off.

Any power tool that cannot be controlled with the
Power Switch is dangerous and must be repaired.

3. Disconnect the battery pack from the
power tool before making any adjustments,
changing accessories, or storing power
tools. Such preventive safety measures reduce

the risk of starting the power tool accidentally.

4. Use clamps or another practical way to secure
and support the work piece to a stable platform.

Holding the work by hand or against your body
leaves it unstable and may lead to loss of control.

5. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool. Power tools are

dangerous in the hands of untrained users.

6. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

7. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

8. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the

power tool for operations different from those

intended could result in a hazardous situation.

Page 3For technical questions, please call 1-888-866-5797.Item 68012

Battery tool use and care

1. Recharge only with the charger specified by
the manufacturer. A charger that is suitable

for one type of battery pack may create a risk

SAFETY OPERATION MAINTENANCESETUP

of fire when used with another battery pack.

2. Use power tools only with specifically
designated battery packs. Use of any other

battery packs may create a risk of injury and fire.

3. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from
one terminal to another. Shorting the battery

terminals together may cause burns or a fire.

4. Under abusive conditions, liquid may be
ejected from the battery; avoid contact.
If contact accidentally occurs, flush with water.
If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the

battery may cause irritation or burns.

Service

Have your power tool serviced by a qualified repair person using only identical replacement parts.

This will ensure that the safety of the power tool is maintained.

Multi-function Tool Safety Warnings

1. Hold power tools by insulated gripping
surfaces when performing an operation where
the cutting tool may contact hidden wiring.

Contact with a ″live″ wire will make exposed metal
parts of the tool ″live″ and shock the operator.

2. Maintain labels and nameplates on the tool.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.

3. Avoid unintentional starting.
Prepare to begin work before turning on the tool.

4. Do not lay the tool down until it has come to
a complete stop. Moving parts can grab the
surface and pull the tool out of your control.

5. When using a handheld power tool,
maintain a firm grip on the tool with both
hands to resist starting torque.

7. The battery Charger gets hot during use.
The Charger’s heat can build up to unsafe
levels and create a fire hazard if it does
not receive adequate ventilation, due to

an electrical fault, or if it is used in a hot environment.
Do not place the Charger on a flammable surface.
Do not obstruct any vents on the Charger.

Especially avoid placing the Charger on carpets
and rugs; they are not only flammable, but they
also obstruct vents under the Charger.

Place the Charger on a stable, solid, nonflammable
surface (such as a stable metal workbench or
concrete floor) at least 1 foot away from all flammable
objects, such as drapes or walls. Keep a fire
extinguisher and a smoke detector in the area.
Frequently monitor the Charger and
Battery Pack while charging.

8. This product is not a toy.

Keep it out of reach of children.

6. Do not leave the tool unattended when the
Battery Pack is connected. Turn off the tool,
and remove the Battery Pack before leaving.

Page 4 For technical questions, please call 1-888-866-5797. Item 68012

9. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.

10. WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities, contains chemicals known to the State
of California to cause cancer and birth defects or
other reproductive harm. Some examples of these
chemicals are:

• Lead from lead-based paints

• Crystalline silica from bricks and cement or other
masonry products

• Arsenic and chromium from chemically
treated lumber
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
(California Health & Safety Code § 25249.5, et seq.)

Lithium Battery Safety Warnings

LITHIUM BATTERIES STORE A

LARGE AMOUNT OF ENERGY

AND WILL VENT FIRE OR

EXPLODE IF MISTREATED:

11. WARNING: The cord of this product contains
lead, a chemical known to the State of California
to cause cancer, and birth defects or other
reproductive harm. Wash hands after handling.
(California Health & Safety Code § 25249.5, et seq.)

12. The warnings, precautions, and instructions
discussed in this instruction manual cannot cover all
possible conditions and situations that may occur.
It must be understood by the operator that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the operator.

1. Keep Battery Pack dry.

2. DO NOT DO ANY OF THE FOLLOWING

TO THE BATTERY PACK:

a. Open,
b. Drop,
c. Short-circuit,
d. Puncture,
e. Incinerate, or
f. Expose to temperatures greater than 140°F.

3. Charge Battery Pack only according
to its Charger’s instructions.

SAFETYOPERATIONMAINTENANCE SETUP

Vibration Safety

This tool vibrates during use.
Repeated or long-term exposure to vibration may
cause temporary or permanent physical injury,
particularly to the hands, arms and shoulders.
To reduce the risk of vibration-related injury:

1. Anyone using vibrating tools regularly or for an
extended period should first be examined by a
doctor and then have regular medical check-ups to
ensure medical problems are not being caused or
worsened from use. Pregnant women or people who
have impaired blood circulation to the hand, past
hand injuries, nervous system disorders, diabetes,
or Raynaud’s Disease should not use this tool.
If you feel any symptoms related to vibration (such
as tingling, numbness, and white or blue fingers),
seek medical advice as soon as possible.

4. Inspect Battery Pack before every use;
do not use or charge if damaged.

2. Do not smoke during use. Nicotine reduces
the blood supply to the hands and fingers,
increasing the risk of vibration-related injury.

3. Wear suitable gloves to reduce the
vibration effects on the user.

4. Use tools with the lowest vibration
when there is a choice.

5. Include vibration-free periods each day of work.

6. Grip tool as lightly as possible (while still keeping
safe control of it). Let the tool do the work.

7. To reduce vibration, maintain the tool as
explained in this manual. If any abnormal
vibration occurs, stop use immediately.

SAVE THESE INSTRUCTIONS.

Page 5For technical questions, please call 1-888-866-5797.Item 68012

Grounding

SAFETY OPERATION MAINTENANCESETUP

the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service
facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician.

TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING
WIRE CONNECTION:
Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded.
Do not modify the power cord plug provided with the tool. Never remove the grounding prong from

Double Insulated Tools: Tools with Two Prong Plugs

1. Tools marked “Double Insulated” do not
require grounding. They have a special
double insulation system which satisfies
OSHA requirements and complies with
the applicable standards of Underwriters
Laboratories, Inc., the Canadian Standard
Association, and the National Electrical Code.

2. Double insulated tools may be used in either of the
120 volt outlets shown in the preceding illustration.

Outlets for 2-Prong Plug

(See Outlets for 2-Prong Plug.)

Extension Cords

Note: Extension cords must not be used with this item’s Charger.

Symbology

Double Insulated

Canadian Standards Association

Underwriters Laboratories, Inc.

V

~

A

OPM

Volts

Alternating Current

Amperes

Oscillations Per Minute

WARNING marking concerning Risk
of Eye Injury. Wear ANSI-approved
safety goggles with side shields.

Read the manual before
set-up and/or use.

WARNING marking
concerning Risk of Fire.
Do not cover Charger ventilation ducts.
Charge on fireproof surface only.

WARNING marking concerning
Risk of Electric Shock.
Properly connect Charger’s power
cord to appropriate outlet.

WARNING marking concerning
Risk of Explosion. Do not puncture,
short, or open battery packs and do
not charge damaged battery packs.

Page 6 For technical questions, please call 1-888-866-5797. Item 68012

Specifications

Charger Input Rating 120VAC / 60Hz

Battery Rating 12V / 1300mAh

Battery Type Li-ion

No Load Speed 10,000-18,000 OPM

Accessories Hex Key

Setup - Before Use:

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this

manual including all text under subheadings therein before set up or use of this product.

Note: For additional information regarding the parts listed in the following pages,

refer to Parts List and Diagram on page 11.

Functions

SAFETYOPERATIONMAINTENANCE SETUP

Speed Control Knob Power Switch

Note: Sanding Pad sold separately.

Charger Indicator LED’s

1. The green LED lights once Charger is plugged in.

Battery Pack

Sanding Pad

Figure A

2. The red LED will light during charging.

3. When Battery Pack is fully charged,
both red and green LED’s will stay lit.

4. If both red and green LED’s flash, the charger and/or
battery are not functioning properly. Stop charging
immediately and contact a qualified technician.

Green LED

Red LED

Figure B

Page 7For technical questions, please call 1-888-866-5797.Item 68012

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this

manual including all text under subheadings therein before set up or use of this product.

SAFETY OPERATION MAINTENANCESETUP

Tool Set Up

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Make sure that the Power Switch is in the off-position and unplug the tool from
its electrical outlet before performing any procedure in this section.

Attachment Installation

1. Use the Hex Wrench to remove the Cap Screw
and Washer and from the end of the Spindle.

2. Install the desired accessory by placing the
accessory’s mounting holes against the
fitting pins on the Spindle. See Figure C.

Spindle

Fitting Pins

Sanding Pad

CAUTION! When attaching the Scraper Blade,

Wood Cutting Blade, or Half-Moon Cutting Blade,
orient the accessory so that the blade faces AWAY
from the handle to avoid injury. See Figure D.

Wood Cutting

Blade

Cap Screw

and Washer

Figure D: Installing Woodcutting Blade

Hex Wrench

3. Replace the Cap Screw and Washer while holding

Hex Wrench

Figure C: Installing Sanding Pad

Page 8 For technical questions, please call 1-888-866-5797. Item 68012

the accessory. Hold the Spindle with the wrench,
then tighten securely using the Hex Wrench.

CAUTION! Make sure that the accessory is
held securely in place by the four fitting pins on
the Spindle as you tighten the Cap Screw.

Note: For sanding, first attach the Sanding Pad to the
tool, then align a sheet of Sandpaper over the pad and
press into place. Once a Sandpaper corner becomes
worn, turn it 120° or replace the sheet with a new one.

Charging

1. Remove the Battery Pack from the end of
the Multi-function Tool housing by pressing
on the striped side tabs of the Pack and
sliding the Pack away from the housing.

2. Place the Battery Pack on a dry fireproof surface in
a room where the temperature is from 50–104° F.

Note: If recharging a newly spent Battery Pack,
allow it to cool completely before charging.

3. Examine the Battery Pack. It must be
undamaged, and a Li-ion type Battery Pack.

Do not charge a cracked, open, or
leaking Battery Pack, or charge a
non-recommended type of Battery Pack.

4. The Battery Pack’s terminals are designed to fit
this Charger specifically. If the Battery Pack does
to not fit the Charger properly, do not try to insert it.

Do not force a Battery Pack into the Charger.

5. Plug the Power Supply into a grounded,
120VAC, 60Hz receptacle. The green LED
will light once Charger is plugged in.

6. Slide the Battery Pack onto the Charger.
The red LED will light and the
green LED will turn off during charging.

Note: The Battery Pack’s capacity will increase
somewhat during the first few charging cycles.

A fully discharged Battery Pack will take about 1 hour
and 15 minutes (or 75 minutes) to fully charge.
Do not charge longer than 1 hour and 15 minutes.

Overcharging the Battery Pack can
damage the battery cells.

7. While charging, the Battery Pack, Charger, and
Power Supply may become warm to the touch.
This is normal, and does not indicate a problem.

8. When Battery Pack is fully charged, both red and
green LED’s will stay lit. Unplug the Charger and
disconnect it from the Battery Pack when finished.

9. Allow the Battery Pack to cool
completely before using it.

10. Press the Battery Buttons to release
Battery Pack from the Charger.

SAFETYOPERATIONMAINTENANCE SETUP

Workpiece and Work Area Set Up

1. Designate a work area that is clean and well-lit.
The work area must not allow access by children
or pets to prevent distraction and injury.

General Operating Instructions

1. Make sure that the Power Switch is in the
off-position, then attach the Battery Pack.

Note: The Battery Pack fits into the Tool housing only one
way. Match up the shape of the tool with the shape of the
housing opening. The Battery Pack should slide easily
into the housing. CAUTION! Do not force it into the Tool.

2. Hold the Tool with both hands and slide
the Power Switch forward to activate.

3. Do not allow contact between Sandpaper, Scraper,
or Blade and workpiece until tool is at full speed.

4. Avoid contact with foreign objects such as metal
screws and nails when sanding, scraping, or cutting.

2. Secure loose workpieces using a vise or clamps
(not included) to prevent movement while working.

3. There must not be objects, such as utility lines,
nearby that will present a hazard while working.

5. Do not apply excessive pressure on the Tool.
Allow the Tool to do the work.

NOTE: Model 68012 comes with a Speed Control Knob
that can be used to adjust the Tool’s speed.
The Speed Control Knob can be set at six different
speeds (1-6). “1” is the lowest oscillation and “6” is the
highest. Use high oscillation (5-6) for work with the
Scraper Blade. NOTE: Conduct a test run on a scrap
workpiece to determine the correct speed for job.

6. When finished, slide the Power Switch to OFF. Allow
the tool to stop completely before setting it down.

7. To prevent accidents remove the tool’s
Battery Pack after use. Clean, then store
the tool indoors out of children’s reach.

Page 9For technical questions, please call 1-888-866-5797.Item 68012

Maintenance and Servicing

Procedures not specifically explained in this manual must

be performed only by a qualified technician.

SAFETY OPERATION MAINTENANCESETUP

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Make sure that the Power Switch is in the off-position and unplug the tool from
its electrical outlet before performing any procedure in this section.

TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal noise or vibration
occurs, have the problem corrected before further use.

Cleaning, Maintenance, and Lubrication

1. BEFORE EACH USE, inspect the general
condition of the tool. Check for:

• leaking, swollen, or cracked battery pack,

• loose hardware,

• misalignment or binding of moving parts,

• cracked or broken parts, and

• any other condition that may

affect its safe operation.

2. AFTER USE, wipe external surfaces
of the tool with clean cloth.

3. Disconnect battery pack and store battery pack,
charger, and tool in dry, indoor area out of
reach of children and away from metal objects
(i.e., paperclips, coins) to prevent shorting.

4. Dispose of Battery Pack properly.

Do not short, incinerate or open Charger or
Battery Pack. Keep Charger and Battery Pack dry.

Troubleshooting

Problem Possible Causes Likely Solutions

Tool will not start. 1. Battery Pack not properly connected.

2. Battery Pack not properly charged.

3. Battery Pack burnt-out.

4. Internal damage or wear.
(Carbon brushes or
Power Switch, for example.)

Tool operates slowly. 1. Forcing tool to work too fast.

2. Battery Pack wearing out.

Performance
decreases over time.

Excessive noise
or rattling.

Overheating. 1. Forcing tool to work too fast.

1. Carbon brushes worn or damaged.

2. Bit dull or damaged.

Internal damage or wear. (Carbon
brushes or bearings, for example.)

2. Bit dull or damaged.

3. Blocked motor housing vents.

1. Remove Battery Pack, make sure there are no
obstructions, reinsert the Battery Pack according
to its shape (it should only fit one way), and press
firmly until the Battery Pack locks in place.

2. Make sure Charger is connected and operating properly.
Give enough time for Battery Pack to recharge properly.

3. Dispose of old Battery Pack properly or recycle.
Replace Battery Pack.

4. Have technician service tool.

1. Allow tool to work at its own rate.

2. Dispose of old Battery Pack properly or recycle.
Replace Battery Pack.

1. Have qualified technician replace brushes.

2. Keep bits sharp. Replace as needed.

Have technician service tool.

1. Allow tool to work at its own rate.

2. Keep bits sharp. Replace as needed.

3. Wear ANSI-approved safety goggles and
NIOSH-approved dust mask/respirator while
blowing dust out of motor using compressed air.

Follow all safety precautions whenever diagnosing or servicing the tool.

Disconnect Battery Pack and Charger power supply before service.

Page 10 For technical questions, please call 1-888-866-5797. Item 68012

Parts List and Diagram

Part Description Qty

1 Circlip for hole 22 1
2 Gasket 1
3 Corrugated gasket 1
4 Spindle Pin 4
5 Cap Screw & Washer 1
6 Scraper Blade 1
7 Bearing 1
8 Spring washer 2

9 Spindle 1
10 Screw M3x10 2
11 Circlip 1
12 Tapping screw ST4x20 2
13 Tapping screw ST4x24 2

Part Description Qty

14 Spring washer 4
15 Front Cover 1
16 Copper sleeve 1
17 Support 1
18 Eccentric wheel 1
19 Bearing 1
20 Paper washer 1
21 Fixed plate of motor 1
22 Bearing 1
23 Motor 1
24 Cushion blocking 2
25 Slide 1
26 Washer 1

Part Description Qty

27 Right housing 1
28 Inner wiring 1
29 Battery pack 1
30 Insert 1
31 Left housing 1
32 Tapping screw ST3X16 3
33 Tapping screw ST3X13 1
34 Speed Control Knob 1
35 Power Switch 1
36 Screw M3x10 2
37 Spring washer 2
38 O-ring 1
39 Charger 1

SAFETYOPERATIONMAINTENANCE SETUP

Record Product’s Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only,

and are not available individually as replacement parts.

Page 11For technical questions, please call 1-888-866-5797.Item 68012

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797