Harbor Freight Tools 67966 User Manual
5 PIECE CAB MOUNTED LIGHT
Model
97966
97967
INSTRUCTIONS AND PRECAUTIONS
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
READ ALL PRECAUTIONS AND INSTRUCTIONS.
Copyright© 2008 by Harbor Freight Tools®. All rights reserved. No portion of this document
or any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools. Diagrams within this document may not
be drawn proportionally. Due to continuing improvements, actual product may differ slightly
from the product described herein.
For technical questions or replacement parts, please call
1-800-444-3353.
UNPACKING
If any parts are missing or broken,
please call Harbor Freight Tools at the number shown on the cover of this document as
soon as possible.
IMPORTANT SAFETY
INFORMATION
Assembly Precautions
Install only according to these instruc-1.
tions. Improper installation can create
hazards.
Wear ANSI-approved safety goggles 2.
and heavy-duty work gloves during
assembly.
Keep installation area clean and well lit.3.
Keep bystanders out of the area during 4.
installation.
Do not install when tired or when under 5.
the inuence of drugs or medication.
Use Precautions
This product is not a toy. Do not allow 1.
children to play with this item.
Use for intended purpose(s) only.2.
Inspect before use; do not use if parts 3.
loose or damaged.
Application of this product must meet 4.
State and DOT requirements for vehicle
lighting.
Turn vehicle off and disconnect the bat-5.
tery before installation.
WARNING: The brass components 6.
of this product contain lead, a chemical known to the State of California to
cause birth defects (or other reproductive harm). (California Health & Safety
code § 25249.5, et seq.)
Maintain product labels and name-7.
plates. These carry important safety
information. If unreadable or missing, contact Harbor Freight Tools for a
replacement.
Page 1SKU 9766-67 For technical questions, please call 1-800-444-3353.
ASSEMBLY INSTRUCTIONS
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of
this document including all
text under subheadings
therein before set up or use of
this product.
Installation
The planned mounting area must 1.
provide a ush t to the bottom of the
Lights (1).
Remove the lens from each Light and 2.
use the base of the Light as a template
to mark mounting holes.
Ensure that the installation area has no 3.
hidden electrical or stereo lines before
drilling.
Drill the holes, then secure each of 4.
the Lights with two Long Screws (2).
Replace the lens.
See Wiring Diagram, page 4.5.
Connect the wire of each of the Lights 6.
to the Lead Wire (8) using a Wire
Splice (4). Insert the two wires into the
holes of the Splice and use pliers (not
included) to push down the metal tab.
Close the cap to secure.
metal tab
If the Lights are to work independently 8.
of the vehicle’s lights, mount the Switch
at a convenient location with the two
Short Screws (3).
Connect the Lead Wire to the middle 9.
terminal of the Switch (7).
Connect the Fuse Holder (5) to the top 10.
terminal and connect to a 12V power
supply.
Connect the Ground Wire (6) to the 11.
bottom terminal of the Switch and the
other end to ground.
This product is intended only to be 12.
mounted on the top of a vehicle’s cab.
Installation of these products must 13.
comply with DOT regulations and all
applicable State and local laws.
PLEASE READ THE
FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR
HAS PROVIDED THE PARTS LIST AND
ASSEMBLY DIAGRAM IN THIS DOCUMENT AS
A REFERENCE TOOL ONLY. NEITHER THE
MANUFACTURER OR DISTRIBUTOR MAKES
ANY REPRESENTATION OR WARRANTY
OF ANY KIND TO THE BUYER THAT HE OR
SHE IS QUALIFIED TO MAKE ANY REPAIRS
TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE
PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS
REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS,
AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING
OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT
PARTS THERETO, OR ARISING OUT OF HIS
OR HER INSTALLATION OF REPLACEMENT
PARTS THERETO.
holes for
cap
wires
Wire Splice (4)
7. If the Lights are intended to be used
along with the vehicle’s main lights,
connect the lead wire to the headlight
switch positive terminal.
Page 2SKU 9766-67 For technical questions, please call 1-800-444-3353.
Loading...