Harbor Freight Tools 67803 User Manual
Corner Laser Level
When unpacking, make sure that the
product is intact and undamaged.
If any parts are missing or broken,
please call 1‑800‑444‑3353
as soon as possible.
Item 67803
INSTRUCTIONS AND
PRECAUTIONS
Visit our website at:
http://www.harborfreight.com
Read this material before using
this product. Failure to do so
can result in serious injury.
SAVE THIS MANUAL.
Copyright© 2011 by Harbor Freight Tools®.
All rights reserved. No portion of this document
or any artwork contained herein may be
reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
Diagrams within this document may not be
drawn proportionally. Due to continuing
improvements, actual product may differ slightly
from the product described herein. Tools required
for assembly and service may not be included.
For technical questions,
please call 1‑800‑444‑3353.
Specications
Range up to 20′ under optimal conditions
Batteries 3 x ‘AA’
Product Labels
AVOID EXPOSURE
Laser light is emitted from
this aperture.
AVOID EXPOSURE
Laser light is emitted from
this aperture.
CORNER LASER
LEVEL
Uses 3 ‘AA’ batteries
(sold separately)
ITEM 67803
LASER LIGHT
AVOID DIRECT EYE EXPOSURE
Max. Output: <5 mW,
Wavelength: 650 nm
CLASS IIIa LASER PRODUCT
This product complies with
21 CFR 1040.10 and 1040.11
Laser Diode Mfr:
Sean & Stephen Corp.,
4F, NO3, Ln. 335, Sec 4,
Hsin-Yi Rd., Taipen, China
Manufacture Date:
_____________ , _________
Important Safety Information
1. Never attach or use any other form
of optical device with this product.
Use as intended only.
2. Do not modify in any way as
this may result in hazardous
radiation exposure.
3. This product is not a toy.
Do not allow children to play
with or near this item.
4. Inspect before every use; do not
use if parts are loose or damaged.
5. Maintain product labels and
nameplates. These carry important
safety information. If unreadable
or missing, contact Harbor Freight
Tools for a replacement.
6. Position batteries in proper polarity
and do not install batteries of
different types, charge levels,
or capacities together.
7. People with pacemakers should
consult their physician(s)
before use. Electromagnetic
elds in close proximity to heart
pacemaker could cause pacemaker
interference or pacemaker failure.
Instructions
Read the ENTIRE
IMPORTANT SAFETY
INFORMATION section
at the beginning of this
document before set up
or use of this product.
2. The Bulls‑eye Level (see Figure A)
can be used to determine if the
surface the level is mounted on
is level. If the bubble is centered
in the circle, the surface is level.
3. The Magnets (see Figure B) are
used to mount the level to a ferrous
(iron‑containing) metal surface.
Battery Replacement
Before rst use or if laser appears
dim, then replace the batteries:
Magnets
Battery Cover
Figure B: Battery Compartment
Power Buttons Bulls‑eye
Level
Laser
Openings
Figure A: Controls
1. The Power Buttons (see Figure A)
allow each of the two
lasers to be switched on
independently from one another.
Point the Laser Openings away
from your eyes before turning on.
Turn off both lasers after use for
safety and to extend battery life.
Page 2 For technical questions, please call 1‑800‑444‑3353. SKU 67803
1. Open the Battery Cover.
2. Remove the old Batteries.
Dispose of them properly or
recharge if rechargeable.
3. Install three ‘AA’ batteries.
Position batteries in proper polarity
and do not install batteries of
different types, charge levels,
or capacities together.
4. Close the Battery Cover.
Record Serial Number Here:
Note: If product has no serial
number, record month and
year of purchase instead.
Note: Replacement parts are
not available for this item.
Loading...