Harbor Freight Tools 67336 User Manual
NOSE, EAR & SIDEBURNS
HAIR TRIMMER
67336
SET UP AND OPERATING INSTRUCTIONS
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright© 2009 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Page 2 For technical questions, please call 1-800-444-3353. SKU 67336
SAVE THIS MANUAL
Keep this manual for the safety
warnings and precautions, assembly,
operating, inspection, maintenance and
cleaning procedures. Write the product’s
serial number in the back of the manual
near the assembly diagram (or month
and year of purchase if product has no
number). Keep this manual and the
receipt in a safe and dry place for future
reference.
IMPORTANT SAFETY
INFORMATION
In this manual, on the labeling,
and all other information
provided with this product:
This is the safety alert
symbol. It is used to alert
you to potential personal
injury hazards. Obey all
safety messages that
follow this symbol to avoid
possible injury or death.
DANGER indicates
a hazardous
situation which, if not
avoided, will result in death or
serious injury.
WARNING
indicates a
hazardous situation which, if
not avoided, could result in
death or serious injury.
CAUTION, used
with the safety
alert symbol, indicates a
hazardous situation which, if
not avoided, could result in
minor or moderate injury.
NOTICE is used to
address practices
not related to personal injury.
CAUTION, without
the safety alert
symbol, is used to address
practices not related to
personal injury.
General Battery Operated Tool
Safety Warnings
WARNING Read all safety
warnings and instructions.
Failure to follow the warnings and
instructions may result in electric
shock, and/or serious injury.
Save all warnings and
instructions for future reference.
Work area safety1.
Keep work area clean and well a.
lit. Cluttered or dark areas invite
accidents.
Keep children and bystanders b.
away while operating the tool.
Distractions can cause you to lose
control.
Personal safety2.
Stay alert, watch what you are a.
doing and use common sense
when operating the tool. Do not
use the tool while you are tired
or under the inuence of drugs,
alcohol or medication. A moment
of inattention may result in serious
personal injury.
Prevent unintentional starting. b.
Ensure the switch is in the off-
Page 3For technical questions, please call 1-800-444-3353.SKU 67336
position before inserting the
battery.
Battery operated tool use and care3.
Do not force the tool. Use the a.
correct tool for your application.
The correct tool will do the job better
and safer at the rate for which it was
designed.
Do not use the tool if the switch b.
does not turn it on and off. Any
tool that cannot be controlled with
the switch is dangerous and must be
repaired.
Do not allow persons unfamiliar c.
with the tool or these instructions
to operate the tool. Battery
operated tools are dangerous in the
hands of untrained users.
Maintain tools. Check for d.
misalignment or binding of
moving parts, breakage of parts
and any other condition that may
affect the tool’s operation. If
damaged, have the tool repaired
before use. Many accidents are
caused by poorly maintained tools.
Keep cutting tools clean.e. Properly
maintained cutting tools are less
likely to bind and are easier to
control.
Use the tool and accessories f.
in accordance with these
instructions. Use of the tool for
operations different from those
intended could result in a hazardous
situation.
Service4.
Have your tool serviced by a a.
qualied repair person using only
identical replacement parts. This
will ensure that the safety of the tool
is maintained.
Trimmer Safety Warnings
The Trimmer is not waterproof and 1.
is not intended to be submerged
or rinsed, with the exception of the
removable Trimming Attachments.
The Trimmer has sharp edges that 2.
can cause injury if not used properly.
Do not insert the Trimmer further into 3.
your nostril or ear than the narrow tip
on the outer blade. Do not press the
Trimmer forcefully into your nostril or
ear. For facial hair only.
Do not attempt to use the Trimmer 4.
if any part of the blade appears
damaged. Injury to the nostril or ear
might occur.
This product is not a toy. Keep it out 5.
of reach of children.
The warnings, precautions, 6.
and instructions discussed in
this instruction manual cannot
cover all possible conditions and
situations that may occur. It must
be understood by the operator that
common sense and caution are
factors which cannot be built into this
product, but must be supplied by the
operator.
SAVE THESE
INSTRUCTIONS.
Page 4 For technical questions, please call 1-800-444-3353. SKU 67336
SPECIFICATIONS
Electrical Input One “AA” Battery (sold separately)
Accessories
- Nose hair trimmer attachment
with Cap
- Sideburns trimmer attachment
UNPACKING
When unpacking, make sure that the
item is intact and undamaged. If any parts
are missing or broken, please call Harbor
Freight Tools at 1-800-444-3353 as soon
as possible.
INSTRUCTIONS FOR
PUTTING INTO USE
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
TO PREVENT
SERIOUS INJURY
FROM ACCIDENTAL
OPERATION:
Slide the Switch to the off
position (toward the Battery
Cover) before adjusting tool
or installing accessories or
the battery.
Note: For additional information regarding
the parts listed in the following pages,
refer to the Assembly Diagram near
the end of this manual.
Functions
Figure 1
Sideburns Trimming
Attachment
Trimmer Body
Battery
Cover (23)
Nose Hair Trimming
Attachment
Cleaning Brush
Cap (9)
Alignment Slot
Switch (27)
Tool Set Up
Installing Battery
Figure 2
Alignment Slot
Switch (27)
Trimmer Body
Battery
Cover (23)
This Trimmer uses one “AA” battery
(sold separately). To install the
battery:
Rotate the Battery Cover (23) counter 1.
clockwise, then pull it off the end of
the Trimmer Body.
Insert one “AA” battery (sold 2.
separately) into the battery
compartment with the polarity placed
as indicated.
Replace the Battery Cover. 3.
Page 8 For technical questions, please call 1-800-444-3353. SKU 67336
Part Description Qty
1 Blade cover 1
2 Sideburns xing blade 1
3 Sideburns moving blade 1
4 Pressure plate 1
5 Spring 1
6 Sideburns blade 1
7 Sideburns Blade holder 1
8 Oscillator 1
9 Cap 1
10 Blade base 1
11 Big blade tube 1
12 Nose Hair Blade holder 1
13 Small moving blade 1
14 Small xing blade 1
Part Description Qty
15 Nose Hair Blade Holder 1
16 Small blade tube 1
17 Swinging head 1
18 Blade holder core 1
19 Body back 1
20 Motor 1
21 Contact plate(+) 1
22 Cover plate 1
23 Battery Cover 1
24 Contact plate(-) 1
25 Body front 1
26 Switch plate 1
27 Switch 1
PARTS LIST & ASSEMBLY DIAGRAM
Page 7For technical questions, please call 1-800-444-3353.SKU 67336
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL ASA REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/
OR DISTRIBUTOR EXPRESSLY STATES THATALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE
BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
Page 6 For technical questions, please call 1-800-444-3353. SKU 67336
MAINTENANCE AND
SERVICING
Procedures not specically
explained in this manual
must be performed only by a
qualied technician.
TO PREVENT
SERIOUS INJURY
FROM ACCIDENTAL
OPERATION:
Slide the Switch to the off
position (toward the Battery
Cover) before performing any
inspection, maintenance, or
cleaning procedures.
TO PREVENT SERIOUS
INJURY FROM TOOL
FAILURE:
Do not use damaged
equipment. If abnormal noise
or vibration occurs, have the
problem corrected before
further use.
Cleaning and Maintenance
BEFORE EACH USE,1. inspect the
general condition of the tool. Check
for loose hardware, misalignment or
binding of moving parts, cracked or
broken parts and any other condition
that may affect its safe operation.
AFTER USE,2. wipe external surfaces
with a clean cloth. Remove and
clean the Trimming Attachment (See
Trimming Attachments - Page 5). Let
air dry completely.
If storing the tool for a long period 3.
of time, remove the battery. Dispose
of spent batteries according to local,
state and federal regulations.
Page 5For technical questions, please call 1-800-444-3353.SKU 67336
Trimming Attachments
This unit comes with two Trimming
Attachments: a narrow tool for
trimming nose hairs and ear hairs,
and a wide attachment for trimming
sideburns.
To remove a Trimming Attachment:1.
Rotate the Trimming Attachment
counter clockwise, then pull it off the
top of the Trimmer Body.
To clean a Trimming Attachment:2.
Use the Cleaning Brush, or clean
in warm water and mild detergent.
Air dry the Attachment completely if
cleaning with water.
CAUTION: The Trimmer is not waterproof
and is not intended to be submerged
or rinsed, with the exception of the
removable Trimming Attachments.
To install a Trimming Attachment:3.
Line up the tabs on the inside of the a.
Attachment with the Alignment Slot
on the Trimmer Body.
Slide the Attachment onto the Body b.
and rotate clockwise to lock in place.
General Operating Instructions
Turn the Trimmer on by sliding the 1.
Switch (27) toward the Trimming
Attachment.
To use the Nose Trimming 2.
Attachment:
Using a mirror (sold separately), a.
slowly and carefully insert the tip of
the Nose Hair Trimming Attachment
into your nostril or ear hole.
Slowly move the Trimmer as needed b.
to trim hair.
To use the Sideburns Trimming 3.
Attachment:
Using a mirror (sold separately),
press the trimmer gently against
your face where you want to trim
your sideburn, then slowly slide it
down the side of your face, trimming
excess hair. Repeat as needed.
CAUTION: Use only on facial hair.
To prevent accidents, turn off the tool 4.
after use. Clean, then store the tool
indoors out of children’s reach.
CAUTION: Do not insert the Trimmer
further into your nostril or ear than the
narrow tip on the outer blade. Do not
press the Trimmer forcefully into your
nostril or ear. For facial hair only.
Do not attempt to use the Trimmer
if any part of the blade appears
damaged. Injury to the nostril or ear
might occur.
Loading...