Page 1
18V CORDLESS WORKLIGHT
67032
SET UP AND OPERATING INSTRUCTIONS
NOTE: BATTERY PACK (67029) SOLD SEPARATELY
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright© 2009 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Page 2
SAVE THIS MANUAL
Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning
procedures. Write the product’s serial
number in the back of the manual near the
assembly diagram (or month and year of
purchase if product has no number). Keep
this manual and the receipt in a safe and
dry place for future reference.
NOTICE is used to
address practices
not related to personal injury.
CAUTION, without
the safety alert
symbol, is used to address
practices not related to
personal injury.
General Flashlight Safety
Warnings
IMPORTANT SAFETY
INFORMATION
In this manual, on the labeling,
and all other information provided with this product:
This is the safety alert
symbol. It is used to alert
you to potential personal
injury hazards. Obey all
safety messages that
follow this symbol to avoid
possible injury or death.
DANGER indicates
a hazardous
situation which, if not
avoided, will result in death or
serious injury.
WARNING
indicates a
hazardous situation which, if
not avoided, could result in
death or serious injury.
CAUTION, used
with the safety
alert symbol, indicates a
hazardous situation which, if
not avoided, could result in
minor or moderate injury.
WARNING Read all safety
warnings and instructions.
Failure to follow the warnings and
instructions may result in electric
shock, re and/or serious injury.
Save all warnings and
instructions for future reference.
Work area safety
Keep work area clean and well lit. a.
Cluttered or dark areas invite acci-
dents.
Keep children and bystanders b.
away while operating any tool.
Distractions can cause you to lose
control.
Electrical safety2.
Do not expose tools to rain or
wet conditions. Water entering the
Flashlight will increase the risk of
electric shock.
Personal safety3.
Stay alert, watch what you are do-a.
ing and use common sense when
operating any tool. Do not use a
tool while you are tired or under
the inuence of drugs, alcohol or
medication.
SKU 67032 For technical questions, please call 1-800-444-3353. Page 2
Page 3
Prevent unintentional starting. b.
Ensure the switch is in the offposition before connecting to battery pack, picking up or carrying
the tool.
Flashlight use and care4.
Do not use the Flashlight if the a.
switch does not turn it on and off.
Disconnect the battery pack from b.
the Flashlight before making any
adjustments, changing accessories, or storing the Flashlight.
Such preventive safety measures
reduce the risk of starting the Flash-
light accidentally.
Maintain the Flashlight. Check c.
for misalignment or binding of
moving parts, breakage of parts
and any other condition that may
affect the Flashlight’s operation.
If damaged, have the Flashlight
repaired before use.
Battery tool use and care5.
Recharge only with the charger a.
specied by the manufacturer. A
charger that is suitable for one type
of battery pack may create a risk of
re when used with another battery
pack.
Use tools only with specically b.
designated battery packs. Use of
any other battery packs may create
a risk of injury and re.
When battery pack is not in use, c.
keep it away from other metal objects, like paper clips, coins, keys,
nails, screws or other small metal
objects, that can make a connection from one terminal to another.
Shorting the battery terminals to-
gether may cause burns or a re.
Under abusive conditions, liquid d.
may be ejected from the battery;
avoid contact. If contact acciden-
tally occurs, ush with water. If
liquid contacts eyes, additionally
seek medical help. Liquid ejected
from the battery may cause irritation
or burns.
Service6.
Have your Flashlight serviced by a.
a qualied repair person using
only identical replacement parts.
This will ensure that the safety of the
Flashlight is maintained.
Flashlight Safety Warnings
Maintain labels and nameplates on 1.
the tool. These carry important safety
information. If unreadable or missing, contact Harbor Freight Tools for a
replacement.
Avoid unintentional starting. Prepare 2.
to begin work before turning on the
tool.
Do not leave the tool unattended 3.
when it is attached to a battery pack.
Turn off the tool, and disconnect it
from its battery pack before leaving.
4. The battery charger gets
hot during use. The
charger’s heat can build
up to unsafe levels and
create a re hazard if it does not
receive adequate ventilation, due to
an electrical fault, or if it is used in a
hot environment.
Do not place the charger on a ammable surface. Do not obstruct any
vents on the charger. Especially
avoid placing the charger on carpets and rugs; they are not only
SKU 67032 For technical questions, please call 1-800-444-3353. Page 3
Page 4
ammable, but they also obstruct
vents under the charger.
Place the charger on a stable, solid,
nonammable surface (such as a
stable metal workbench or concrete
oor) at least 1 foot away from all
ammable objects, such as drapes or
walls. Keep a re extinguisher and a
smoke detector in the area. Frequently monitor the charger and
battery while charging.
V~
Symbology
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
Volts Alternating Current
This product is not a toy. Keep it out 5.
of reach of children.
People with pacemakers should 6.
consult their physician(s) before use.
Electromagnetic elds in close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure. In addition, people with
pacemakers should:
• Avoid operating alone.
• Properly maintain and inspect to
avoid electrical shock.
The warnings, precautions, and in-7.
structions discussed in this instruction
manual cannot cover all possible conditions and situations that may occur.
It must be understood by the operator
that common sense and caution are
factors which cannot be built into this
product, but must be supplied by the
operator.
A
n0 xxxx/min.
Amperes
No Load Revolutions per Minute
(RPM)
SAVE THESE
INSTRUCTIONS.
Extension Cords
Note: Extension cords must not be used
with this item’s charger.
SKU 67032 For technical questions, please call 1-800-444-3353. Page 4
Page 5
SPECIFICATIONS
OPERATING INSTRUCTIONS
Battery Type 18V NiCd - SKU 67029
Charger SKU 67031
Bulb 10W incandescent, XPR-18
Accessories Spare Bulb in Lamp Head Housing
UNPACKING
When unpacking, make sure that the
item is intact and undamaged. If any parts
are missing or broken, please call Harbor
Freight Tools at 1-800-444-3353 as soon
as possible.
INSTRUCTIONS FOR
PUTTING INTO USE
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
Note: For additional information regarding
the parts listed in the following pages,
refer to the Parts List and Assembly
Diagram near the end of this manual.
Functions
Lamp Head Housing (7)
Power Switch (2)
Tool Set Up
TO PREVENT
SERIOUS INJURY
FROM ACCIDENTAL
OPERATION:
Turn the Power Switch of the
tool to its “OFF” position and
disconnect the tool from its
Battery Pack before
performing any inspection,
maintenance, or cleaning
procedures.
Charge the Battery
The Charger (SKU 67031) and
Rechargeable Battery Pack (SKU
67029) are sold separately. Please
refer to the 67031 Charger manual
for important safety warnings and
proper instructions on charging tool.
WARNING! Do NOT use a different
Charger or Battery Pack to power this
tool.
General Operating Instructions
Attach the fully charged Battery Pack 1.
(sold separately) to the base of the
Flashlight.
Slide the Power Switch (2) to ON 2.
by sliding it towards the Lamp Head
Housing (7).
Adjust the direction of the light by 3.
pivoting the Lamp Head Housing (7)
of the light clockwise, up to 90°.
Lens Retainer (15)
Battery Pack
(SKU 67029)
(Sold Separately)
Figure 1
Turn off the Flashlight and disconnect 4.
its power supply after use. Clean,
then store the tool indoors out of children’s reach.
SKU 67032 For technical questions, please call 1-800-444-3353. Page 5
Page 6
MAINTENANCE AND
SERVICING
Procedures not specically
explained in this manual
must be performed only by a
qualied technician.
TO PREVENT
SERIOUS INJURY
FROM ACCIDENTAL
OPERATION:
Turn the Power Switch of the
tool to its “OFF” position and
disconnect the tool from its
battery pack before
performing any inspection,
maintenance, or cleaning
procedures.
Lamp Head Housing (7)
Spare Bulb (12)
Reector (13)
Lens (14)
Lens Retainer (15)
Spring (11)
Bulb (12)
Figure 2
3. To change the bulb:
Unthread the Lens Retainer (15) a.
counterclockwise and carefully re-
move the Lens (14), Reector (13)
and spent Bulb (12), noting which
side of the lens faces the Reector.
TO PREVENT SERIOUS
INJURY FROM TOOL
FAILURE:
Do not use damaged
equipment.
Cleaning & Maintenance
BEFORE EACH USE,1. inspect the
general condition of the tool. Check
for loose hardware, misalignment or
binding of moving parts, cracked or
broken parts, damaged electrical wiring, and any other condition that may
affect its safe operation.
AFTER USE,2. wipe external surfaces
of the tool with clean cloth.
Slide the spare bulb (12) (included) b.
out of its slot in the Lamp Head
Housing (7) and place it in the
Spring (11) in the center of the Lamp
Head Housing.
Replace the Reector, the Lens, and c.
the Lens Reector.
Note: Purchase a new spare bulb to store
inside the Lamp Head Housing for
future use.
SKU 67032 For technical questions, please call 1-800-444-3353. Page 6
Page 7
PARTS & ASSEMBLY DIAGRAM
Part Description Qty
1 Strap 1
2 Power Switch 1
3 Switch 1
4 Housing 1
5 Tapping Screw ST2.9 x 16 2
6 Rotation Limiting Plate 1
7 Lamp Head Housing 1
8 Clamp Plate 1
9 Wiring Board 1
10 Positive Spring 1
Part Description Qty
11 Spring 1
12 Bulb, XPR-18 2
13 Reector 1
14 Lens 1
15 Lens Retainer 1
16 Contact Plate 1
17 Contact Strip 2
19 Tapping Screw ST2.9 x16 5
20 Housing 1
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 67032 For technical questions, please call 1-800-444-3353. Page 7
Page 8
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/
OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE
BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
LIMITED 90 DAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from
the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities,
criminal activity, improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental,
contingent, special or consequential damages arising from the use of our product. Some
states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection veries the defect, we will either repair or replace the product at our election or we may elect to refund the purchase
price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect
resulted from causes not within the scope of our warranty, then you must bear the cost
of returning the product.
This warranty gives you specic legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 67032 For technical questions, please call 1-800-444-3353. Page 8
Loading...