Harbor Freight Tools 66838 User Manual
SIT/STAND
SPECIFICATIONS
ROLLING WALKER
66838
INSTRUCTIONS AND PRECAUTIONS
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
SAVE THESE INSTRUCTIONS.
READ ALL PRECAUTIONS
AND INSTRUCTIONS.
Copyright© 2009 by Harbor Freight Tools®. All
rights reserved. No portion of this document or any
artwork contained herein may be reproduced in any
shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this document
may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the
product described herein. Tools required for assembly
and service may not be included.
For technical questions or replacement parts, please
call 1-800-444-3353
Weight Capacity 225 lb.
Handle Height Adjustment 6 Positions
UNPACKING
When unpacking, make sure item is intact
and undamaged. If parts are missing or broken,
call Harbor Freight Tools at 1-800-444-3353.
IMPORTANT SAFETY
INFORMATION
Assemble according to these instructions. 1.
Improper assembly can create hazards.
WARNING! 2. This product should only be used
by a person who has the physical capability
to safely walk and sit on this device.
Do not exceed 225 lb. weight capacity. 3. Be
aware of dynamic loading! Sudden load
movement may briey create excess load
causing product failure
Use as intended only; Walker is not a 4.
wheel chair. Do not use to carry people.
Wear ANSI-approved safety goggles and 5.
heavy-duty work gloves during assembly.
Make sure Walker is fully opened, Seat is 6.
down and folding bar beneath Seat is locked
before use.
Make sure Handles are of equal height 7.
before use. If one is lower than the other,
adjust accordingly. Apply gentle pressure to
Handles to test Walker stability before use.
Test Brakes before use. If Wheels turn while 8.
Brakes are locked, have an authorized tech-
nician adjust Brakes. DO NOT use Walker if
Brakes do not work properly.
Lock Brakes before sitting on Seat. Do not sit 9.
on Seat unless you on even, level ground.
Inspect before every use; do not use if parts 10.
are loose or damaged. Check tires regularly
and replace when worn.
This product is not a toy. Do not allow chil-11.
dren to play with or near this item.
Maintain product labels and nameplates. 12.
These carry important safety information.
If unreadable or missing, contact Harbor
Freight Tools for a replacement.
ASSEMBLY INSTRUCTIONS
Read the ENTIRE IMPORTANT
SAFETY INFORMATION section at the
beginning of this document including
all text under subheadings therein
before set up or use of this product.
Open Rolling Walker. Push down on Support 1.
Hinges (41) until they lock securely in place.
The Support Hinges are located directly below the Seat (16). See Figure 1, below.
The Brake Cable (7) should already be 2.
fastened to the Push Handles (2). Place the
Push Handles into the Front Frame (17) and
set to the required height using the Screw
Caps (13) and Screws (10). Fasten securely.
WARNING! Make sure that both Push
Handles are set at the same height.
Insert the removable Backrest Bar (52) into 3.
the slots on the Front Frame and fasten into
place by inserting the Retainer Pins (14).
See Figure 2, below.
16
41
Figure 1
52
14
Figure 2
Use the Fasteners (26) to clasp the Basket 4.
(25) or PVC Bag (51) to the Cross Bolt (27)
and the Back Frame (18).
OPERATION
To properly sit in the chair, rst make sure 1.
the Walker is on a level surface.
Then check the brakes and grab both 2.
Handles (4).
Carefully back into the Walker. Do NOT fall 3.
back into the Walker.
To slow down or temporarily stop the Walker 4.
during use, squeeze the Brake Handles (6)
rmly. See Figure 3, below.
To lock the Wheels (38) in position, push 5.
down on Brake Handles until a “click” sound
is heard.
To unlock the Wheels, pull upon the Brake 6.
Handles.
Regularly 7. test the tension on the Brake
Handles to ensure that Brakes work properly.
It may be necessary to adjust the tension of
the brake cable. This type of adjustment is
similar to the kind performed on a bicycle.
To tighten the tension on the brake cable, 8.
use a wrench (not included) to turn the 10mm
Nut under the Handle clockwise. See Figure
4, below.
6
Figure 3
Brake Cable
10mm Nut
Figure 4
SKU 66838 For technical questions, please call 1-800-444-3353. Page 2
Loading...