Harbor Freight Tools 66244 Product manual
35” STEEL
TRAILER
66244
TONGUE BOX
INSTRUCTIONS AND PRECAUTIONS
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
SAVE THESE INSTRUCTIONS. READ ALL
PRECAUTIONS AND INSTRUCTIONS.
Copyright© 2008 by Harbor Freight Tools®. All rights reserved. No portion of this document or any artwork contained
herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this document may not be drawn proportionally. Due to continuing improvements, actual product
may differ slightly from the product described herein. Tools required for assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
SPECIFICATIONS
Overall Dimensions 12”L x 35”W x 12-1/8”L
Mounting Hole Size 5/16” Diameter
UNPACKING
When unpacking, check to make sure that
the item is intact and undamaged. If any parts are
missing or broken, please call Harbor Freight Tools
at the number shown on the cover of this document
as soon as possible.
IMPORTANT SAFETY
INFORMATION
Installation Precautions
Set up only according to these instructions. 1.
Improper assembly can create hazards.
Wear ANSI-approved safety goggles and 2.
heavy-duty work gloves during assembly.
Keep assembly area clean and well lit.3.
Keep bystanders out of the area during set 4.
up.
Do not assemble when tired or when under 5.
the inuence of alcohol, drugs or medication.
Use Precautions
This product is not a toy. Do not allow chil-1.
dren to play with or near this item.
Use only as intended only.2.
Inspect before every use; do not use if parts 3.
are loose or damaged. Periodically check to
be sure the “U” bolts, support plates and nuts
are rmly attached.
Maintain product labels and nameplates. 4.
These carry important safety information.
If unreadable or missing, contact Harbor
Freight Tools for a replacement.
WARNING: The brass components of this 5.
product contain lead, a chemical known to
the State of California to cause birth defects
(or other reproductive harm). (California
Health & Safety code § 25249.5, et seq.)
REV 09c
INSTALLATION INSTRUCTIONS
Read the ENTIRE IMPORTANT
SAFETY INFORMATION section at the
beginning of this document including
all text under subheadings therein
before set up or use of this product.
This item is assembled when you receive 1.
it. However, it must be mounted onto your
trailer tongue.
Place the Tool Box on the trailer tongue (not 2.
supplied) with the wider part near the trailer.
From the Hardware Pack (6) select a “U” bolt 3.
and insert it through one of the rectangular
support plates. Insert the legs of the “U” bolt
through the holes in the bottom of the Tool
Box to align with the supports on your trailer
tongue. Repeat with the other “U” bolt.
Fit a rectangular support plate over the legs 4.
of a “U” bolt and hold in place with two nuts
and washers from the Hardware Pack (6).
Repeat for other side. Tighten all 4 bolts,
rmly clamping the Tool Box onto your trailer
tongue.
Before use, check to be sure the Tool Box is 5.
rmly attached to the trailer tongue.
NOTE: Two keys are provided. Keep these in 6.
a safe place when not in use.
Occasionally apply a lock lubricant to the 7.
lock to keep it in good condition.
PARTS LIST & ASSEMBLY
DIAGRAM
Part Description Qty.
1 Box 1
2 Lid 1
3 Hinge 1
4 Gas Lid Support 1
5 Lock 1
6 Hardware Pack 1
7 Gasket 1
8 Keys (not shown) 2
Record Serial Number Here:
Note: If product has no serial number, record
month and year of purchase instead.
Note: Some parts are listed and shown for illustra-
tion purposes only, and are not available
individually as replacement parts.
PLEASE READ THE FOLLOWING
CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS
PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS DOCUMENT AS A REFERENCE TOOL ONLY.
NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY
KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED
TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT
HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF
THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS
AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT
BY THE BUYER. THE BUYER ASSUMES ALL RISK AND
LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO,
OR ARISING OUT OF HIS OR HER INSTALLATION OF
REPLACEMENT PARTS THERETO.
SKU 66244 For technical questions, please call 1-800-444-3353. Page 2
Loading...