Harbor Freight Tools 65779 Owner's Manual
HELPING
65779
HANDS WITH
LED LIGHT
INSTRUCTIONS AND PRECAUTIONS
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
SAVE THESE INSTRUCTIONS. READ ALL
PRECAUTIONS AND INSTRUCTIONS.
Copyright© 2008 by Harbor Freight Tools®. All rights reserved. No portion of this document or any artwork contained
herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this document may not be drawn proportionally. Due to continuing improvements, actual product
may differ slightly from the product described herein. Tools required for assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
SPECIFICATIONS
Magnication
1. Magnifying Lens - 2x
2. Zoom Lens - 6x
UNPACKING
When unpacking, make sure that the item
is intact and undamaged. If any parts are missing
or broken, please call Harbor Freight Tools at the
number shown on the cover of this document as
soon as possible.
IMPORTANT SAFETY
INFORMATION
Assembly Precautions
Assemble only according to these instruc-1.
tions. Improper assembly can create haz-
ards.
Wear ANSI-approved safety goggles during 2.
assembly.
Keep assembly area clean and well lit.3.
Keep bystanders out of the area during as-4.
sembly.
Do not assemble when tired or when under 5.
the inuence of drugs or medication.
Use Precautions
This product is not a toy. Do not allow chil-1.
dren to play with this item.
Use for intended purpose(s) only.2.
Inspect before use; do not use if parts are 3.
loose or damaged.
Maintain product labels and nameplates. 4.
These carry important safety information.
If unreadable or missing, contact Harbor
Freight Tools for a replacement.
ASSEMBLY INSTRUCTIONS
Read the ENTIRE IMPORTANT
SAFETY INFORMATION section at the
beginning of this document including
all text under subheadings therein
before set up or use of this product.
Assembly
Pop the back of the Battery Compartment 1.
Cover up, and remove.
Insert the three AAA batteries supplied; the 2.
correct polarity is shown in the compartment.
When batteries are installed, close cover.
Insert the Coil Spring Soldering Iron Holder 3.
(9) into the hole on the right side of Base (1)
and tighten the Lock Screw. (See Fig. 1.)
Insert the Vertical Rod (2) into the Base and 4.
tighten the Lock Screw. (See Fig. 1.)
Slide the Horizontal Rod (3) and Bracket 5.
down onto the Vertical Rod.
Slide down about half way and tighten the a.
knob. This position can be adjusted later.
(See Fig. 1.)
Slide the Magnifying Lens (4) and Bracket 6.
onto the Vertical Rod (2) and tighten knob.
(See Fig. 1.)
Adjust as required.7.
Lighting
The LED lights are not designed to be re-8.
placed.
PLEASE READ THE FOLLOWING
CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS
PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS DOCUMENT AS A REFERENCE TOOL ONLY.
NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY
KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED
TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT
HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF
THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS
AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT
BY THE BUYER. THE BUYER ASSUMES ALL RISK AND
LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO,
OR ARISING OUT OF HIS OR HER INSTALLATION OF
REPLACEMENT PARTS THERETO.
PARTS LIST & ASSEMBLY
DIAGRAM
Part Description Qty.
1 Cast Iron Base 1
2 Vertical Rod 1
3 Horizontal Rod 1
4 Magnifying Lens 1
5 Zoom Lens 1
6 LED Bulb (Beneath Battery Compartment) 2
7 AAA Batteries 3
8 LED Light Switch 1
9 Coil Spring Soldering Iron Holder 1
Note: Replacement parts are not available.
Battery Compartment Cover
Zoom Lens (5)
Magnifying Lens (4)
Lock Knob
Vertical Rod (2)
LED Light
Switch (8)
Lock Knob
Alligator Clips
Cast Iron Base w/Sponge Tray (1)
Coil Spring Soldering
Iron Holder (9)
Horizontal Rod (3)
Fig 1
Record Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available individually as
replacement parts.
SKU 65779 For technical questions, please call 1-800-444-3353. Page 2
Loading...