Harbor Freight Tools 65620 Product manual
MOTORCYCLE
SWINGARM
65620
REAR LIFT
AND STAND
INSTRUCTIONS AND PRECAUTIONS
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
SAVE THESE INSTRUCTIONS. READ ALL
PRECAUTIONS AND INSTRUCTIONS.
Copyright© 2008 by Harbor Freight Tools®. All rights reserved. No portion of this document or any artwork contained
herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this document may not be drawn proportionally. Due to continuing improvements, actual product
may differ slightly from the product described herein. Tools required for assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
SPECIFICATIONS
Weight Capacity 1000 lbs.
Width Capacity
Rubber Coated Casters 3" Diameter
From 10-1/4" to 13-3/8"
(outside width of swing
arm)
UNPACKING
When unpacking, make sure that the item
is intact and undamaged. If any parts are missing
or broken, please call Harbor Freight Tools at the
number shown on the cover of this document as
soon as possible.
IMPORTANT SAFETY
INFORMATION
Assembly Precautions
Assemble only according to these instruc-1.
tions. Improper assembly can create haz-
ards.
Wear ANSI-approved safety goggles and 2.
heavy-duty work gloves during assembly.
Keep assembly area clean and well lit.3.
Keep bystanders out of the area during as-4.
sembly.
Do not assemble when tired or when under 5.
the inuence of drugs, alcohol or medication.
Use Precautions
This product is not a toy. Do not allow chil-1.
dren to play with or near this item.
Use for intended purpose(s) only.2.
Inspect before use; do not use if parts are 3.
loose or damaged.
Maintain product labels and nameplates. 4.
These carry important safety information.
If unreadable or missing, contact Harbor
Freight Tools for a replacement.
ASSEMBLY INSTRUCTIONS
Read the ENTIRE IMPORTANT
SAFETY INFORMATION section at the
beginning of this document including
all text under subheadings therein
before set up or use of this product.
Assembly
Refer to the assembly drawing for these 1.
instructions.
Locate two Axles (5).2.
Locate eight Flat Washers (8), four Casters 3.
(6), four Lock Nuts (4) and two Bushing (7).
Insert Axles (5) and into the axle brackets lo-4.
cated on the outside curved part of the Stand
Frame (1).
Slide a Flat Washer (8) over each end of the 5.
Axle (5) and up against the axle bracket.
Slide a Bushing (7) over the ends of the Axle 6.
(5) and up against the Flat Washers.
Slide two Casters (6) over each end of the 7.
Axle and over the Bushings (7).
Slide another Washer over each end of the 8.
axle and up against the side of the Caster.
Screw a Lock Nut (4) onto each end of the 9.
Axle locking the assembly together.
Repeat for the Caster assembly on the other 10.
side.
Slide each Paddle Style Adapter (2) into the 11.
square adapter bracket at the end of each
Bracket.
To lift the front of the motorcycle, Front Fork a.
Adapters (9) SKU 65621, are available.
Screw a Knob (3) into the threaded hole at 12.
the top of each square adapter bracket and
tighten.
These Knobs hold the Adapters at their a.
desired width positions.
Operation
Adjust the position of the Paddle Adapters (2) 1.
to match motorcycle’s dual swing arm width.
Loosen Knobs (3) holding Adapters (2). a.
Slide the Adapters outward.b.
Roll the Stand behind the motorcycle so that c.
the motorcycle is in the middle of the Stand
Frame.
Move Stand to where the Paddles are under d.
the swing arm.
Adjust Paddle Adapters (2) inward into posi-e.
tion.
Make sure the Paddles are snug up against f.
the swing arm and tighten Knobs (3).
SKU 65620 For technical questions, please call 1-800-444-3353. Page 2
Loading...