Harbor Freight Tools 6510 User Manual
10” BENCH GRINDER
6510
SET UP AND OPERATING INSTRUCTIONS
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright© 1997 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Manual Revised 09d
CONTENTS
UNPACKING .................................. 9
IMPORTANT SAFETY
INFORMATION ............................ 3
GENERAL TOOL SAFETY
WARNINGS ......................................3
GROUNDING INSTRUCTIONS ..... 5
110-120 V~ GROUNDED TOOLS:
TOOLS WITH THREE PRONG
PLUGS .............................................5
110-120 V~ DOUBLE INSULATED
TOOLS: TOOLS WITH TWO
PRONG PLUGS ...............................6
GRINDER SAFETY WARNINGS ........ 6
SPECIFICATIONS .......................... 9
ASSEMBLY .................................. 10
TOOL REST ASSEMBLY ................. 10
EYE SHIELD ASSEMBLY ................10
GRINDING WHEEL ASSEMBLY ...... 11
OPERATION ................................ 13
OPERATION NOTES ........................ 13
GENERAL OPERATION .................. 13
PARTS LIST ................................. 14
ASSEMBLY DIAGRAM ................ 15
LIMITED 1 YEAR / 90 DAY
WARRANTY .............................. 16
Page 2 For technical questions, please call 1-800-444-3353. SKU 6510
SAVE THIS MANUAL
Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning
procedures. Write the product’s serial
number in the back of the manual near the
assembly diagram (or month and year of
purchase if product has no number). Keep
this manual and the receipt in a safe and
dry place for future reference.
IMPORTANT SAFETY
INFORMATION
In this manual, on the labeling,
and all other information provided with this product:
This is the safety alert
symbol. It is used to alert
you to potential personal
injury hazards. Obey all
safety messages that
follow this symbol to avoid
possible injury or death.
NOTICE is used to
address practices
not related to personal injury.
CAUTION, without
the safety alert
symbol, is used to address
practices not related to
personal injury.
General Tool Safety Warnings
WARNING Read all safety
warnings and instructions.
Failure to follow the warnings and
instructions may result in electric
shock, re and/or serious injury.
Save all warnings and
instructions for future reference.
KEEP GUARDS IN PLACE and in 1.
working order.
REMOVE ADJUSTING KEYS AND 2.
WRENCHES. Form habit of checking to see that keys and adjusting
wrenches are removed from tool
before turning it on.
DANGER indicates
a hazardous
situation which, if not
avoided, will result in death or
serious injury.
WARNING
indicates a
hazardous situation which, if
not avoided, could result in
death or serious injury.
CAUTION, used
with the safety
alert symbol, indicates a
hazardous situation which, if
not avoided, could result in
minor or moderate injury.
KEEP WORK AREA CLEAN. Clut-3.
tered areas and benches invite accidents.
DON’T USE IN DANGEROUS EN-4.
VIRONMENT. Don’t use power tools
in damp or wet locations, or expose
them to rain. Keep work area well
lighted.
KEEP CHILDREN AWAY. All visitors 5.
should be kept safe distance from
work area.
MAKE WORKSHOP KID PROOF 6.
with padlocks, master switches, or by
removing starter keys.
Page 3For technical questions, please call 1-800-444-3353.SKU 6510
DON’T FORCE TOOL. It will do the 7.
job better and safer at the rate for
which it was designed.
USE RIGHT TOOL. Don’t force tool 8.
or attachment to do a job for which it
was not designed.
glasses only have impact resistant
lenses, they are NOT safety glasses.
SECURE WORK. Use clamps or a 12.
vise to hold work when practical. It’s
safer than using your hand and it
frees both hands to operate tool.
RECOMMENDED MINIMUM WIRE
GAUGE FOR EXTENSION CORDS
(120 VOLT)
NAMEPLATE
AMPERES
(at full load)
0 – 6 18 16 16 14
6.1 – 10 18 16 14 12
10.1 – 12 16 16 14 12
12.1 – 16 14 12 Do not use.
EXTENSION CORD
LENGTH
25’ 50’ 100’ 150’
TABLE A
USE PROPER EXTENSION CORD. 9.
Make sure your extension cord is
in good condition. When using an
extension cord, be sure to use one
heavy enough to carry the current
your product will draw. An undersized
cord will cause a drop in line voltage
resulting in loss of power and overheating. Table A shows the correct
size to use depending on cord length
and nameplate ampere rating. If in
doubt, use the next heavier gauge.
The smaller the gauge number, the
heavier the cord.
WEAR PROPER APPAREL. Do not 10.
wear loose clothing, neckties, rings,
bracelets, or other jewelry which may
get caught in moving parts. Nonslip
footwear is recommended. Wear protective hair covering to contain long
hair.
ALWAYS USE SAFETY GLASSES. 11.
Also use face or dust mask if cutting
operation is dusty. Everyday eye-
DON’T OVERREACH. Keep proper 13.
footing and balance at all times.
MAINTAIN TOOLS WITH CARE. 14.
Keep tools sharp and clean for best
and safest performance. Follow
instructions for lubricating and changing accessories.
DISCONNECT TOOLS before ser-15.
vicing; when changing accessories,
such as blades, bits, cutters, and the
like.
REDUCE THE RISK OF UNINTEN-16.
TIONAL STARTING. Make sure
switch is in off position before plugging in.
USE RECOMMENDED ACCESSO-17.
RIES. Consult the owner’s manual for
recommended accessories. The use
of improper accessories may cause
risk of injury to persons.
NEVER STAND ON TOOL. Serious 18.
injury could occur if the tool is tipped
or if the cutting tool is unintentionally
contacted.
CHECK DAMAGED PARTS. Before 19.
further use of the tool, a guard or
other part that is damaged should
be carefully checked to determine
that it will operate properly and perform its intended function – check for
alignment of moving parts, binding
of moving parts, breakage of parts,
mounting, and any other conditions
that may affect its operation. A guard
Page 4 For technical questions, please call 1-800-444-3353. SKU 6510
or other part that is damaged should
be properly repaired or replaced.
equipment-grounding conductor to a
live terminal.
DIRECTION OF FEED. Feed work 20.
into a blade or cutter against the direction of rotation of the wheel only.
GROUNDING INSTRUCTIONS
TO PREVENT
ELECTRIC SHOCK
AND DEATH FROM
INCORRECT GROUNDING
WIRE CONNECTION
READ AND FOLLOW THESE
INSTRUCTIONS:
110-120 V~ Grounded Tools: Tools
with Three Prong Plugs
In the event of a malfunction or 1.
breakdown, grounding provides a
path of least resistance for electric
current to reduce the risk of electric
shock. This tool is equipped with an
electric cord having an equipmentgrounding conductor and a grounding plug. The plug must be plugged
into a matching outlet that is properly
installed and grounded in accordance
with all local codes and ordinances.
Do not modify the plug provided – if it 2.
will not t the outlet, have the proper
outlet installed by a qualied electri-
cian.
Improper connection of the equip-3.
ment-grounding conductor can result in a risk of electric shock. The
conductor with insulation having an
outer surface that is green with or
without yellow stripes is the equipment-grounding conductor. If repair
or replacement of the electric cord or
plug is necessary, do not connect the
Check with a qualied electrician or 4.
service personnel if the grounding
instructions are not completely understood, or if in doubt as to whether the
tool is properly grounded.
Use only 3-wire extension cords that 5.
have 3-prong grounding plugs and
3-pole receptacles that accept the
tool’s plug.
Repair or replace damaged or worn 6.
cord immediately.
Grounding
Pin
125 V~ 3-Prong Plug and Outlet
(for up to 125 V~ and up to 15 A)
This tool is intended for use on a cir-7.
cuit that has an outlet that looks like
the one illustrated above in 125 V~
3-Prong Plug and Outlet. The tool
has a grounding plug that looks like
the plug illustrated above in 125 V~
3-Prong Plug and Outlet.
The outlet must be properly installed 8.
and grounded in accordance with all
codes and ordinances.
Do not use an adapter to connect this 9.
tool to a different outlet.
Page 5For technical questions, please call 1-800-444-3353.SKU 6510
Loading...