Harbor Freight Tools 60565 Owner's Manual

WARNING SYMBOLS AND DEFINITIONS

This is the safety alert symbol. It is used to alert you to

potential personal injury hazards. Obey all safety messages

that follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,

Indicates a hazardous situation which, if not avoided,

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

could result in death or serious injury.

could result in minor or moderate injury.

Addresses practices not related to personal injury.

Important Safety Information

Read all safety warnings and instructions.

Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

Installation Safety

1. Keep children and bystanders away
while installing the cameras. Distractions

can cause you to lose control.

2. Do not overreach when installing
this product. Keep proper footing
and balance at all times. This enables

better control in unexpected situations.

3. Wear ANSI-approved safety
goggles during installation.

4. This product is not a toy. Mount
it out of reach of children.

Operation Safety

1. Do not operate electrically powered
products in explosive atmospheres,
such as in the presence of flammable
liquids, gases, or dust. Electrically

powered products create sparks which
may ignite the dust or fumes.

2. The adapter must match the outlet.
Never modify the plug in any way.

Unmodified plugs and matching outlets
will reduce risk of electric shock.

Page 2 For technical questions, please call 1-800-444-3353. Item 60565

3. Do not expose the Power Adapter of

this product to rain or wet conditions.

Water entering the Power Adapter will
increase the risk of electric shock.

4. Do not abuse the Power Cord. Never
use the cord for unplugging the plug
from the outlet. Keep cord away
from heat, oil, sharp edges or moving
parts. Damaged or entangled cords

increase the risk of electric shock.

5. WARNING: Handling the cord on this product
will expose you to lead, a chemical known
to the State of California to cause cancer,
and birth defects or other reproductive harm.
Wash hands after handling. (California
Health & Safety Code § 25249.5, et seq.)

Service Safety

6. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by
the operator that common sense and caution
are factors which cannot be built into this
product, but must be supplied by the operator.

1. Product service must be performed

only by a qualified technician.

2. When servicing a product, use only
identical replacement parts.

3. Maintain this product with care.
Keep this product clean. Do not use

a damaged product. Tag damaged
products “Do not use” until repaired.

4. Disconnect the AC/DC Power Adapter
from the power source before making any
adjustments, changing accessories, or
storing this product. Such preventive safety

measures reduce the risk of electric shock.

5. Maintain labels and nameplates on the unit.
These carry important safety information.
If unreadable or missing, contact Harbor
Freight Tools for a replacement.

SAVE THESE INSTRUCTIONS.

Grounding

TO PREVENT ELECTRIC SHOCK AND DEATH FROM
INCORRECT GROUNDING WIRE CONNECTION:
Check with a qualified electrician if you are in doubt as to whether the outlet is

Never remove the grounding prong from the plug. Do not use the system if the power cord or
plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will
not fit the outlet, have a proper outlet installed by a qualified electrician.

properly grounded. Do not modify the power cord plug provided with the system.

1. The included adapter does
not require grounding.

2. The adapter may be used in either
of the 120 volt outlets shown in the
preceding illustration. (See Figure A.)

Figure A: Outlets for 2-Prong Plug

Page 3For technical questions, please call 1-800-444-3353.Item 60565

Grounding (continued)

Extension Cords

Note: Do not use an extension

cord with this item’s adapter.

Symbology

Double Insulated

Canadian Standards
Association

Underwriters
Laboratories, Inc.

Specifications

V

~

A

MONITOR

Power Adapter

Screen Size 4.3" Diagonal
Color Configuration R.G.B. Delta
Resolution 480 (H) x 272 (V)
Operating
Temperature
Operating Humidity 85% Maximum
Dimensions 5-1/4" L x 5-1/8" W x 1" H
Weight 0.5 lb.

Image Sensor 1/4" Color CMOS
Horizontal Resolution 380 TV lines
Effective Pixels NTSC: 658 (H) x 492 (V)
Focal Length 6 mm
Minimum Illumination 1.0 lux without LED
Night Vision Active (Illuminated) Infrared
Video Output 1.0 Vp-p75Ω
Signal/Noise Ratio >48 dB
Camera Power Input DC 9 –12 V / 200 mA
Dimensions 2" L x 1-1/2" W x 2-1/2" H

120 V~ / 60 Hz Input
12 VDC / 1 A Output

14º to 122º F

CAMERA

Volts

Alternating Current

Amperes

Page 4 For technical questions, please call 1-800-444-3353. Item 60565