Harbor Freight Tools 60395 Owner's Manual
Specifications
Rated Capacity 300 lb.
Maximum Lift Height 24"
Axle Width 36" - 51"
Wheel Bracket Size 11" W x 8.5-12.5" L
SAFETY OPERATION MAINTENANCEASSEMBLY
IMPORTANT SAFETY INFORMATION
Failure to heed these warnings may result in personal injury and/or property damage:
Assembly Precautions
1. Assemble only according to these instructions.
Improper assembly can create hazards.
2. Wear ANSI-approved safety goggles and
heavy-duty work gloves during assembly.
3. Keep assembly area clean and well lit.
Use Precautions
1. Study, understand, and follow all instructions
before operating this device.
2. Do not exceed rated capacity.
3. Use only on hard, level surfaces.
4. Keep bystanders out of the area during assembly.
5. Do not assemble when tired or when under the
influence of alcohol, drugs or medication.
6. Weight capacity and other product capabilities apply
to properly and completely assembled product only.
17. Stay alert. Watch what you are doing, and use
common sense when operating a Jack. Do not use
a Jack while tired or under the influence of drugs,
alcohol, or medication. A moment of inattention while
operating Jacks may result in serious personal injury.
4. Center load on Jack platforms.
5. Lift only using tires.
6. Immediately after lifting load, ensure Jack
mechanical load holding means is engaged.
7. Do not move while loaded.
8. Secure load with appropriate restraint device.
9. Do not adjust safety valve.
10. Wear ANSI-approved safety goggles and
heavy-duty work gloves during use.
11. Keep clear of load while lifting and lowering.
12. Lower load slowly.
13. Do not use for aircraft purposes.
14. Inspect before every use; do not use
if parts loose or damaged.
15. Keep your work area clean and well lit.
Cluttered work areas invite accidents.
16. Do not allow anyone on the vehicle while
using the Jack. Keep bystanders a safe
distance away from the vehicle and Jack.
18. Store idle Jacks out of reach of
children and other untrained persons.
Jacks are dangerous in the hands of untrained users.
19. Jack service must be performed
only by qualified repair personnel.
Service or maintenance performed by
unqualified personnel could result in a risk of injury.
20. When servicing a jack, use only identical replacement
parts. Follow instructions in the “Inspection,
Maintenance, And Cleaning” section of this manual.
Use of unauthorized parts or failure to follow
maintenance instructions may create a risk of injury.
21. Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact Harbor Freight Tools for a replacement.
22. Before use, read manufacturer’s instruction
manual for the vehicle you will lift.
23. Do not support both ends of the
vehicle at the same time.
24. Before lowering the Jack, remove all tools
and equipment from under the vehicle.
25. The warnings, precautions, and instructions
discussed in this manual cannot cover all
possible conditions and situations that may occur.
The operator must understand that common sense
and caution are factors, which cannot be built into
this product, but must be supplied by the operator.
SAVE THESE INSTRUCTIONS.
Page 2 For technical questions, please call 1-800-444-3353. Item 60395
Assembly Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before set up or use of this product.
1. Raise Shaft (24) and insert Shaft Pin (18) through its base.
Place Washer (11) over the end of the Shaft Pin (18).
Insert R-Clip (13) through the end of the Shaft Pin (18) to secure it.
Shaft (24)
Shaft
Pin (18)
Step 1: Raise Shaft
SAFETYOPERATIONMAINTENANCE ASSEMBLY
R-Clip
(13)
Washer (11)
2. Position the Ram (16) as shown.
Slide a Pin (8) through the Ram Base (14) and the Base (6).
Place Washer (11) over the end of the Pin (8).
Secure Pin with R-clip (13).
Ram (16)
Pin (8)
Ram
Base (14)
R-clip
(13)
Washer (11)
Step 2: Connect Ram Base
Page 3For technical questions, please call 1-800-444-3353.Item 60395
3. Connect top of Ram (16) to Lift Arm (25) using Lift Arm Pin (27).
Slide a Washer (11) over each end of the Lift Arm Pin.
Secure Lift Arm Pin using an R-clip (13) on each end.
SAFETY OPERATION MAINTENANCEASSEMBLY
Lift Arm Pin (27)
Washer (11) Washer (11)
Lift Arm (25)
Ram (16)
R-clip (13)
R-clip (13)
Step 3: Connect top of Ram
4. Insert Beam (21) through the Beam Bracket (29).
Insert Pin (8) through center of Beam Bracket.
Hold Washer (11) over end of Pin and secure it with Spring Pin (1).
Beam (21)
Pin (8)
Beam
Bracket (29)
Washer (11)
Spring Pin (1)
Step 4: Attach Beam
Page 4 For technical questions, please call 1-800-444-3353. Item 60395
Loading...