Harbor Freight Tools 60315 Product manual

Specifications

ITEM Rated Load

Max.

Height

60315 3 Tons (6,000 lb.) 44″ 24-3⁄4″

60350 8 Tons (16,000 lb.) 43-1⁄2″ 24-1⁄2″

Min.

Height

Base Type

⁄8″ Round Pin Holes

60393 3 Tons (6,000 lb.) 42-1⁄4″ 23″ 4″ x 4-1⁄2″ Flat

60394 8 Tons (16,000 lb.) 42″ 23″ 4-3⁄8″ x 5-1⁄4″ Flat

WARNING SYMBOLS AND DEFINITIONS

This is the safety alert symbol. It is used to alert you to

potential personal injury hazards. Obey all safety messages

that follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Ram Pin

Hole

⁄8″

Addresses practices not related to personal injury.

Page 2 For technical questions, please call 1-800-444-3353. Long Ram Jack

IMPORTANT SAFETY INFORMATION

Read all safety warnings and instructions. Failure to follow the warnings and

instructions may result in serious injury and DEATH from sudden failure of Jack or device.

Save all warnings and instructions for future reference.

1. Study, understand, and follow all instructions before operating this device.

2. Install ONLY on device designed

for a Jack with the same rating:

• A device designed for a Jack with a higher rating may damage the Jack or cause it to suddenly fail under load.

• A device designed for a Jack with a lower rating may be damaged or may suddenly fail under load.

3. Mount properly as part

of a device designed for this type of Jack before use. Mounting points, maximum length, and rating must be IDENTICAL.

Do not mount on different device or use while not mounted properly.

4. Do not use upside-down.

5. Do not adjust safety valve.

6. Wear ANSI-approved safety goggles and heavy-duty work gloves during use.

7. Keep clear of load while lifting and lowering.

8. Lower load slowly.

9. Do not use for aircraft purposes.

10. Inspect before every use; do not use if parts loose or damaged.

11. Keep your work area clean and well lit. Cluttered work areas invite accidents.

12. Keep bystanders, children, and visitors away while operating Jack.

13. Stay alert. Watch what you are doing, and use common sense when operating a Jack. Do not use a Jack while tired or under the influence of drugs, alcohol, or medication.

14. Jack service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury.

15. When servicing a Jack, use only identical replacement parts. Follow instructions in the “Inspection, Maintenance, and Cleaning” section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of injury.

16. Maintain labels and nameplates on the Jack. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement.

17. Industrial applications must follow OSHA requirements.

18. The warnings, precautions, and instructions discussed in this manual cannot cover all possible conditions and situations that may occur. The operator must understand that common sense and caution are factors, which cannot be built into this product, but must be supplied by the operator.

SAVE THESE INSTRUCTIONS.

Page 3For technical questions, please call 1-800-444-3353.Long Ram Jack

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product.

Mounting

WARNING! Install ONLY on device designed for a Jack with the same rating:

• A device designed for a Jack with a higher rating may damage the Jack or cause it to suddenly fail under load.

• A device designed for a Jack with a lower rating may be damaged or may suddenly fail under load.

WARNING! Mount properly as part of a device designed for this type of Jack before use. Mounting points, maximum length, and rating must be IDENTICAL.

Do not mount on different device or use while not mounted properly.

Note: Do not mount upside-down.

Note: Jack must have load

on Piston to retract.

WARNING! Only use pins that are capable of supporting the rated load, and ensure that the pins are properly secured before use. Make sure the pins’ diameters are a push fit with just enough clearance so they move freely.

1. Secure the Base to the device:

a. Round Base:

Insert a pin (not included) through the holes in the Round Base and in the device, properly securing it.

b. Flat Base:

Secure Flat Base to the device according to device supplier’s instructions.

2. Insert another pin (not included) through the device and Ram Pin Hole.

3. Secure pins in place with appropriate retaining rings or cotter pins (both sold separately).

Ram Pin

Hole

Flat Base

Page 4 For technical questions, please call 1-800-444-3353. Long Ram Jack

Base Pin

Holes

+ 8 hidden pages