Harbor Freight Tools 60238 User Manual

Table of Contents

Safety ......................................................... 2

Specifications ............................................. 6

Setup .......................................................... 6

SAFETY OPERATION MAINTENANCESETUP

Operation .................................................... 8

This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

Maintenance .............................................. 12

Parts List and Diagram .............................. 14

Warranty .................................................... 16

WARNING SYMBOLS AND DEFINITIONS

Obey all safety messages that follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Addresses practices not related to personal injury.

IMPORTANT SAFETY INFORMATION

General Tool Safety Warnings

Read all safety warnings and instructions.

Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

1. KEEP GUARDS IN PLACE and in working order.

2. REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it on.

5. KEEP CHILDREN AWAY. All visitors should
be kept safe distance from work area.

6. MAKE WORKSHOP KID PROOF with padlocks,
master switches, or by removing starter keys.

3. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite accidents.

4. DON’T USE IN DANGEROUS ENVIRONMENT.
Don’t use power tools in damp or wet locations,
or expose them to rain. Keep work area well lighted.

Page 2 For technical questions, please call 1-800-444-3353. Item 60238

7. DON’T FORCE TOOL. It will do the job better
and safer at the rate for which it was designed.

8. USE RIGHT TOOL. Don’t force tool or attachment
to do a job for which it was not designed.

General Tool Safety Warnings (cont.)

Table A: RECOMMENDED MINIMUM WIRE GAUGE

FOR EXTENSION CORDS

(120 VOLT)

NAMEPLATE

AMPERES

(at full load)

0 – 6 18 16 16 14

6.1 – 10 18 16 14 12

10.1 – 12 16 16 14 12

12.1 – 16 14 12 Do not use.

9. USE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using
an extension cord, be sure to use one heavy
enough to carry the current your product will
draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating.
Table A shows the correct size to use depending
on cord length and nameplate ampere rating.
If in doubt, use the next heavier gauge.
The smaller the gauge number, the heavier the cord.

10. WEAR PROPER APPAREL. Do not wear
loose clothing, gloves, neckties, rings, bracelets,
or other jewelry which may get caught in moving
parts. Nonslip footwear is recommended.
Wear protective hair covering to contain long hair.

11. ALWAYS USE SAFETY GLASSES. Also use
face or dust mask if cutting operation is dusty.
Everyday eyeglasses only have impact resistant
lenses, they are NOT safety glasses.

12. SECURE WORK. Use clamps or a vise to hold
work when practical. It’s safer than using your
hand and it frees both hands to operate tool.

EXTENSION CORD

LENGTH

25′ 50′ 100′ 150′

13. DON’T OVERREACH. Keep proper
footing and balance at all times.

14. MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.

15. DISCONNECT TOOLS before servicing;
when changing accessories, such as
blades, bits, cutters, and the like.

16. REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure switch is in
off position before plugging in.

17. USE RECOMMENDED ACCESSORIES.
Consult the owner’s manual for recommended
accessories. The use of improper accessories
may cause risk of injury to persons.

18. NEVER STAND ON TOOL. Serious injury
could occur if the tool is tipped or if the
cutting tool is unintentionally contacted.

19. CHECK DAMAGED PARTS. Before further use
of the tool, a guard or other part that is damaged
should be carefully checked to determine that
it will operate properly and perform its intended
function – check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting, and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or replaced.

20. DIRECTION OF FEED. Feed work into
a blade or cutter against the direction of
rotation of the blade or cutter only.

21. NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN POWER OFF. Don’t leave tool
until it comes to a complete stop.

SAFETYOPERATIONMAINTENANCE SETUP

Page 3For technical questions, please call 1-800-444-3353.Item 60238

Grounding Instructions

SAFETY OPERATION MAINTENANCESETUP

TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING WIRE CONNECTION
READ AND FOLLOW THESE INSTRUCTIONS:

110-120 V~ Grounded Tools: Tools with Three Prong Plugs

1. In the event of a malfunction or breakdown,
grounding provides a path of least resistance for
electric current to reduce the risk of electric shock.
This tool is equipped with an electric cord having an
equipment-grounding conductor and a grounding
plug. The plug must be plugged into a matching
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.

2. Do not modify the plug provided – if it will
not fit the outlet, have the proper outlet
installed by a qualified electrician.

3. Improper connection of the equipment-grounding
conductor can result in a risk of electric shock.
The conductor with insulation having an outer
surface that is green with or without yellow
stripes is the equipment-grounding conductor.
If repair or replacement of the electric cord or
plug is necessary, do not connect the equipment­grounding conductor to a live terminal.

4. Check with a qualified electrician or service
personnel if the grounding instructions are
not completely understood, or if in doubt as
to whether the tool is properly grounded.

5. Use only 3-wire extension cords that
have 3-prong grounding plugs and 3-pole
receptacles that accept the tool’s plug.

6. Repair or replace damaged or worn cord immediately.

Grounding

Pin

125 V~ 3-Prong Plug and Outlet

(for up to 125 V~ and up to 15 A)

7. This tool is intended for use on a circuit that has
an outlet that looks like the one illustrated above in
125 V~ 3-Prong Plug and Outlet. The tool has a
grounding plug
that looks like the plug illustrated above
in 125 V~ 3-Prong Plug and Outlet.

8. The outlet must be properly installed and grounded
in accordance with all codes and ordinances.

9. Do not use an adapter to connect
this tool to a different outlet.

Drill Press Safety Warnings

For Your Own Safety Read Instruction

Manual Before Operating Drill Press

1. Wear eye protection.

2. Do not wear gloves, necktie, or loose clothing.

3. Clamp workpiece or brace against
column to prevent rotation.

4. Use recommended speed for drill
accessory and workpiece material.

5. The included chuck key is specially designed
to be self-ejecting, reducing the risk of ejecting
at high speed. Only use the included chuck
key or an identical replacement key.

6. DO NOT OPERATE WITH ANY GUARD DISABLED,

DAMAGED, OR REMOVED. Moving guards
must move freely and close instantly.

Page 4 For technical questions, please call 1-800-444-3353. Item 60238

7. The use of accessories or attachments not
recommended by the manufacturer may
result in a risk of injury to persons.

8. When servicing use only identical replacement parts.

9. Only use safety equipment that has been approved
by an appropriate standards agency. Unapproved
safety equipment may not provide adequate
protection. Eye protection must be ANSI-approved
and breathing protection must be NIOSH-approved
for the specific hazards in the work area.

10. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication.
A moment of inattention while operating power
tools may result in serious personal injury.

Drill Press Safety Warnings (cont.)

11. Industrial applications must follow OSHA guidelines.

12. Maintain labels and nameplates on the tool.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.

13. Avoid unintentional starting.
Prepare to begin work before turning on the tool.

14. To prevent FIRE, do not install a larger

bulb in this item′s bulb holder than

listed in the specifications chart.

15. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.

16. WARNING: Some dust created by power
sanding, sawing, grinding, drilling, and other
construction activities, contains chemicals
known [to the State of California] to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:

• Lead from lead-based paints

• Crystalline silica from bricks and cement or other

masonry products

• Arsenic and chromium from

chemically treated lumber
Your risk from these exposures varies,
depending on how often you do this type of work.
To reduce your exposure to these chemicals:
work in a well ventilated area, and
work with approved safety equipment, such
as those dust masks that are specially
designed to filter out microscopic particles.
(California Health & Safety Code § 25249.5, et seq.)

17. WARNING: Handling the cord on this product will
expose you to lead, a chemical known to the State
of California to cause cancer, and birth defects or
other reproductive harm. Wash hands after handling.
(California Health & Safety Code § 25249.5, et seq.)

18. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.

SAFETYOPERATIONMAINTENANCE SETUP

Vibration Safety

This tool vibrates during use. Repeated or long-term
exposure to vibration may cause temporary or permanent
physical injury, particularly to the hands, arms and
shoulders. To reduce the risk of vibration-related injury:

1. Anyone using vibrating tools regularly or for an
extended period should first be examined by a
doctor and then have regular medical check-ups
to ensure medical problems are not being caused
or worsened from use. Pregnant women or
people who have impaired blood circulation to
the hand, past hand injuries, nervous system
disorders, diabetes, or Raynaud’s Disease should
not use this tool. If you feel any medical or
physical symptoms related to vibration (such as
tingling, numbness, and white or blue fingers),
seek medical advice as soon as possible.

SAVE THESE INSTRUCTIONS.

2. Do not smoke during use. Nicotine reduces
the blood supply to the hands and fingers,
increasing the risk of vibration-related injury.

3. Use tools with the lowest vibration when there
is a choice between different processes.

4. Include vibration-free periods each day of work.

5. Grip tool as lightly as possible (while still keeping
safe control of it). Let the tool do the work.

6. To reduce vibration, maintain the tool as
explained in this manual. If any abnormal
vibration occurs, stop use immediately.

Page 5For technical questions, please call 1-800-444-3353.Item 60238

Specifications

Electrical Rating 120V~ / 60Hz / 2.4A

SAFETY OPERATION MAINTENANCESETUP

Spindle Speeds

Table Tilt 45º left and right

Swing 8"

Spindle Stroke 2"

Spindle Taper B16

Chuck Capacity 1/16″ - 1/2″ (13mm)

Worklight Bulb Size E14 base, 120V, 15W

760, 1150, 1630, 2180, 3070 RPM
5 Speeds

Setup - Before Use:

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this

manual including all text under subheadings therein before set up or use of this product.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the tool off and unplug the tool from its electrical
outlet before performing any procedure in this section.

227541

Note: For additional information regarding the parts listed in the following pages,

refer to the Assembly Diagram near the end of this manual.

Mounting

Secure the tool to a supporting structure before use.
Before assembly, bolt the Base to a flat, level,
solid workbench capable of supporting the
weight of the drill press and any workpieces.

Verify that installation surface has no hidden
utility lines before drilling or driving screws.

Assembly

Column to Base

1. Place Column (8) on the Base (1) and align
holes in the Column with holes in the Base.

2. Attach using Bolt (5), Spring Washer (4),
and Washer (3) in each hole through
the Column and into the Base.

Column (8)

Bolt (5)

Base (1)

Figure A: Column to Base Connection

Page 6 For technical questions, please call 1-800-444-3353. Item 60238

Table Support

1. Loosen the Pivot Lever (51).

2. Slide the Table Support (52) over the Column (8).

3. Tighten the Pivot Lever to secure
the Table Support in place.

Headstock and Feed Handles

1. Loosen the two Set Screws (9) on the
right side of the Headstock (42) so they
will stay clear while installing it.

Table

Support (52)

Figure B: Installing Table Support

Headstock (42)

Column (8)

SAFETYOPERATIONMAINTENANCE SETUP

Pivot

Lever (51)

2. With the help of an assistant, lift the Headstock
above the Column (8), and gently slide it
down the Column as far as it will go.

3. Tighten the two Set Screws to secure
the Headstock in place.

4. Thread the Feed Handles (6) into the
Feed Seat (7) and tighten them.

Set

Screws

(9)

Feed

Handle (6)

Feed

Seat (7)

Figure C: Installing Headstock and Feed Handles

Page 7For technical questions, please call 1-800-444-3353.Item 60238

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this

manual including all text under subheadings therein before set up or use of this product.

SAFETY OPERATION MAINTENANCESETUP

Tool Set Up

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the tool off and unplug the tool from its electrical
outlet before performing any procedure in this section.

TO PREVENT SERIOUS INJURY:
DO NOT OPERATE WITH ANY GUARD DISABLED, DAMAGED, OR REMOVED.
Moving guards must move freely and close instantly.

Table Adjustment

1. Adjust the Table (54) by loosening the
Pivot Lever (51), moving the Table,
and tightening the Pivot Lever.

2. Tilt the Table by loosening the Angle Bolt (56) and
tilting to the required angle.
The angle can be read using the Angle Scale (53).

Table

Support (52)

Column (8)

3. TO ENSURE THAT THE DRILL IS ENTIRELY
PERPENDICULAR TO THE TABLE,
insert a straight round bar (not included)
in the Chuck (72), place a square on the
Table (54) and bring it up to the round bar.
Adjust the angle as needed.

CAUTION! To prevent injury from unexpected
Table movement, tighten Angle Bolt (56)
and Pivot Lever (51) after adjustment.

Setting a Drilling Depth

Located around the Spindle Feed Shaft is a
Depth Stop Collar (A) with a scale. The collar is
capable of turning about the shaft, and may be
locked in place by a Locking Screw (B).

1. Lower the drill (with the power OFF) so that it
contacts the material and hold in that position.

2. Loosen the locking screw and turn the collar
so that the measurement for the depth of the
hole required is in line with the pointer (C).

Angle Bolt (56)

under Table

Figure D: Table Adjustment

Figure E: Drill Depth Adjustment

Pivot

Lever (51)

3. Lock the collar in this position using the locking screw.

Page 8 For technical questions, please call 1-800-444-3353. Item 60238

Changing Drill Speed

Before changing the speeds, make sure the
machine is switched OFF and UNPLUGGED.

1. Open the pulley cover.

2. Loosen the Motor Tension Knob (10) on the
Headstock (42), and move the Motor (14) towards
the Headstock to relieve tension on the Belt (59).

Lamp

(34)

Motor Tension

Knob (10)

Light Bulb (73)

3. Consult the chart below and position
the Belt (59) on the Pulleys (16, 60)
according to the desired drill speed.

4. When the Belt has been correctly positioned, tighten
it by pushing the Motor away from the Headstock until

the belt deflects by approximately 1/2″ at its center

when using reasonable thumb pressure. Lock this
position in with the Motor Tension Knob (10).

SAFETYOPERATIONMAINTENANCE SETUP

Deflection

Distance

Figure G: Belt Deflection

Note: If either belt is too long to be properly

tensioned, it must be replaced.

Figure F: Motor Tension Knob location

760 RPM

Spindle Motor

The table above shows the belt arrangements for given drill speeds.
A full chart is also located on the inside of the pulley cover.

1150 RPM

Spindle Motor

1630 RPM

Spindle Motor

Figure H: Drill Speed Table

Light Bulb Installation

1. To prevent injury, allow the old
Light Bulb (73) to cool completely first.

2. Remove the old Light Bulb (73) from the
Lamp (34) and dispose of it properly.

3. Install a new Light Bulb of the same type and rating.
(E14 base, 120V, 15W)

WARNING! TO PREVENT SERIOUS INJURY
FROM FIRE: Do not install a different style Light Bulb
or a Light Bulb with a higher wattage rating.

Drill Bit Installation

2180 RPM

Spindle Motor

3070 RPM

Spindle Motor

1. Insert the drill bit into the jaws of the Chuck

approximately 1″, ensuring that the jaws

do not touch the flutes of the drill bit.

2. Before tightening the Chuck, ensure that
the drill bit is centered within the jaws.

3. Tighten the Chuck securely with
the included Chuck Key.

Page 9For technical questions, please call 1-800-444-3353.Item 60238

Workpiece and Work Area Set Up

1. Designate a work area that is clean and well-lit.
The work area must not allow access by children
or pets to prevent distraction and injury.

SAFETY OPERATION MAINTENANCESETUP

2. Route the power cord along a safe route to reach
the work area without creating a tripping hazard or
exposing the power cord to possible damage. The
power cord must reach the work area with enough
extra length to allow free movement while working.

3. Secure loose workpieces using a vise or clamps
(not included) to prevent movement while working.

4. There must not be objects, such as utility lines,
nearby that will present a hazard while working.

5. Make sure the table height and position
is set so that the drill travel range is
sufficient for the material to be drilled.

6. Make sure the work is securely clamped.
That is, held in a drill vise, or bolted to the table.
Never hold the material with your bare hands while
drilling. Severe personal injury may be caused if
the material is flung out of the operator’s hand.

9. FOR SMALL MATERIALS that cannot be clamped
to the table, use a drill press vise. Make sure
the vise is clamped or bolted to the table.

10. WHEN DRILLING COMPLETELY THROUGH
WOOD, position a piece of scrap wood between the
material and the table to prevent splintering on the
underside of the material as the drill breaks through.
The scrap piece of wood must make contact with
the left side of the column. Securely clamp the
other end of the scrap wood to the table. Also, set
the depth of the drill so that the drill will not come
in contact with the table - or align the table so that
the hole in its center is in line with the drill bit.

7. IF THE MATERIAL IS IRREGULARLY SHAPED and
cannot be laid flat on the table, it should be securely
blocked and clamped. Any tilting, twisting or shifting
will result not only in a roughly drilled hole but also
increases the chances of damage to the drill.

8. FOR FLAT WORK, lay the piece on to a
wooden base and clamp it down firmly against
the table to prevent it from turning.

Figure I: Bracing workpiece against column

Page 10 For technical questions, please call 1-800-444-3353. Item 60238

General Operating Instructions

1. Bring the drill bit down with the Feed Knob to where
the hole is to be drilled.
Make minor workpiece alignment adjustments.

2. Plug the Power Cord into an electrical outlet.

3. Turn the Drill Press on.

4. Pull down on the Feed Knob and slowly
drill the hole into the workpiece.

WARNING! If the drill bit grabs and spins the workpiece,
do not attempt to stop the spinning with your hands.
Step back, and turn the drill press off. Wait for the
spindle to stop turning before dislodging the workpiece.

5. To prevent accidents, turn off the tool and
disconnect its power supply after use. Clean, then
store the tool indoors out of children’s reach.

SAFETYOPERATIONMAINTENANCE SETUP

Page 11For technical questions, please call 1-800-444-3353.Item 60238

Maintenance and Servicing

Procedures not specifically explained in this manual must

be performed only by a qualified technician.

SAFETY OPERATION MAINTENANCESETUP

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the tool off and unplug the tool from its electrical
outlet before performing any procedure in this section.

TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal noise or vibration
occurs, have the problem corrected before further use.

Cleaning, Maintenance, and Lubrication

1. BEFORE EACH USE, inspect the general
condition of the tool. Check for:

• loose hardware,

• misalignment or binding of moving parts,

• cracked or broken parts,

• damaged electrical wiring, and

• any other condition that may

affect its safe operation.

Belt Inspection and Tensioning

1. Examine belt for cracks, tears in
the backing, and other damage.

2. Replace belt if damaged, following the instructions
under Changing Drill Speed on page 9.

2. AFTER USE, wipe external surfaces
of the tool with clean cloth.

3. WARNING! If the supply cord of this

power tool is damaged, it must be replaced
only by a qualified service technician.

Page 12 For technical questions, please call 1-800-444-3353. Item 60238

Troubleshooting

Problem Possible Causes Likely Solutions

Tool will not start. 1. Cord not connected.

2. No power at outlet.

3. Tool’s thermal reset breaker
tripped (if equipped).

4. Internal damage or wear. (Carbon
brushes or switch, for example.)

Tool operates
slowly.

Performance
decreases
over time.

Excessive noise
or rattling.

Overheating. 1. Forcing machine to work too fast.

Extension cord too long or
wire size too small.

1. Accessory dull or damaged.

2. Carbon brushes worn or damaged.

1. Internal damage or wear. (Carbon
brushes or bearings, for example.)

2. Belt (if equipped) too loose (slipping)
or too tight (bearing damage).

2. Accessory dull or damaged.

3. Blocked motor housing vents.

4. Motor being strained by long or
small diameter extension cord.

1. Check that cord is plugged in.

2. Check power at outlet. If outlet is unpowered,
turn off tool and check circuit breaker.
If breaker is tripped, make sure circuit is right
capacity for tool and circuit has no other loads.

3. Turn off tool and allow to cool.
Press reset button on tool.

4. Have technician service tool.

Eliminate use of extension cord. If an extension cord
is needed, use one with the proper diameter for its
length and load. See Table A on page 3.

1. Keep cutting accessories sharp. Replace as needed.

2. Have qualified technician replace brushes.

1. Have technician service tool.

2. Properly tension belt.

1. Allow machine to work at its own rate.

2. Keep cutting accessories sharp. Replace as needed.

3. Wear ANSI-approved safety goggles and
NIOSH-approved dust mask/respirator while
blowing dust out of motor using compressed air.

4. Eliminate use of extension cord. If an extension cord
is needed, use one with the proper diameter for
its length and load. See Table A on page 3.

SAFETYOPERATIONMAINTENANCE SETUP

Follow all safety precautions whenever diagnosing or servicing

the tool. Disconnect power supply before service.

Page 13For technical questions, please call 1-800-444-3353.Item 60238

Parts List and Diagram

PLEASE READ THE FOLLOWING CAREFULLY

SAFETY OPERATION MAINTENANCESETUP

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Parts List

Part Description Qty

1 Base 1
2 Column Support 1
3 Flat Washer 8 5
4 Spring Washer 8 3
5 Bolt M8×20 3
6 Feed Handle 3
7 Feed Seat 1
8 Column 1

9 Set Screw M8×10 2
10 Motor Tension Knob 1
11 Spring 1
12 Slide Bar 1
13 Rubber Pad 1
14 Motor 1
15 Set Screw M6×10 2
16 Motor Pulley 1
17 Bolt M8×16 2
18 Rubber Pad 4
19 Nut M4 1
20 Rubber Ring 1
21 Pulley Cover 1
22 Bolt M5×10 1
23 Flat Washer 5 1
24 Washer 6 5
25 Bolt M6×12 4
26 Wire Clamp 1
27 Screw M4×8 3
28 Rubber Ring 1
29 Knob 1
30 Screw M6×10 2
31 Wire Clamp 2
32 Nut M10 1
33 Flat Washer 10 2
34 Lamp 1
35 Nut M6 1
36 Switch 1
37 Switch Panel 1

Part Description Qty

38 Power Cord 1
39 Nut M10 4
40 Spring Cap 1
41 Depth Spring 1
42 Headstock 1
43 Switch Box 1
44 Flat Washer 4 2
45 Bolt M4×12 2
46 Switch Panel 1
47 Screw ST2.9×10 2
48 Switch 1
49 Nut M8 1
50 Set Screw 1
51 Pivot Lever 1
52 Table Support 1
53 Angle Scale 1
54 Table 1
55 Spring Washer 12 1
56 Angle Bolt M12×25 1
57 Pointer 1
58 Pointer Stud 1
59 V-Belt K-660 1
60 Spindle Pulley 1
61 Retaining Ring 22 1
62 Internal Spindle Sleeve 1
63 Retaining Ring 40 2
64 Ball Bearing 6203 2
65 Retaining Ring 12 1
66 Ball Bearing 6201 2
67 Gasket 1
68 Spindle Sleeve 1
69 Bolt M6×25 1
70 Bracket 1
71 Spindle 1
72 Chuck 1
73 Light Bulb 1

Record Product’s Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only,

and are not available individually as replacement parts.

Page 14 For technical questions, please call 1-800-444-3353. Item 60238

Assembly Diagram

59

15

60

61

62

63

64

64

63

57

39

39

58

24

48

73

47

46

45

34

44

33

39

39

43

40

33

38

41

30

31

42

32

29

35

27 36

49

50

28

37

27 26

20

19

18

10

9

25

24

23

22

21

17

3

13

12

11

8

16

15

14

SAFETYOPERATIONMAINTENANCE SETUP

65

66

67

68

66

69

70

71

72

35

56

55

54

53

52

51

7

6

5

4

3

2

1

Page 15For technical questions, please call 1-800-444-3353.Item 60238

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • [phone]