Harbor Freight Tools 47274 User Manual

ELECTRIC PAINT

®

SPRAY GUN

Model 47274

ASSEMBLY and OPERATING

INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at http://www.harborfreight.com

Copyright © 2002 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.

For technical questions and replacement parts, please call 1-800-444-3353

Specifications

E222975

Power Supply 110 V, 60 Hz, 80 Watts
Container Capacity 33 Ounces
Maximum Pressure 1450 PSI / 100 Bar - Flow Rate = 5.1 GPH
Maximum Viscosity 30 (Seconds) Refer to page 5 (test).
Handle Length 5 Inches
Gun Dimensions 9-1/2” H x 4-1/2” W (weight = 3 Lbs.)
Accessories: Viscosity Cup with hanger/ Four Nozzle Tips including 2 - .032”,
1 - .021”, 1 - Extended Tip - .021”, / Angled Nozzle Adapter (50 Degree)

Save This Manual

You will need the manual for the safety warnings and precautions, assembly instructions,
operating and maintenance procedures, parts list and diagram. Keep your invoice with this
manual. Write the invoice number on the inside of the front cover. Keep the manual and
invoice in a safe and dry place for future reference.

Safety Warnings and Precautions

WARNING: When using tool, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.

Read all instructions before using this tool!

1. Keep work area clean. Cluttered areas invite injuries.

2. Observe work area conditions. Do not use machines or power tools in damp or wet

locations. Don’t expose to rain. Keep work area well lighted. Do not use electrically
powered tools in the presence of flammable gases or liquids. Do not spray near open
flames, pilot lights, or any other heat source. Do not smoke while working with
spraying tools. Always work in a well ventilated area. Paints, sealers, stains and
thinner emit toxic fumes and are extremely flammable.

3. Keep children away. Children must never be allowed in the work area. Do not let

them handle machines, tools, or extension cords.

4. Store idle equipment. When not in use, tools must be stored in a dry location to

inhibit rust. Always lock up tools and keep out of reach of children.

5. Do not force tool. It will do the job better and more safely at the rate for which it was

intended. Do not use inappropriate attachments in an attempt to exceed the tool
capacity.

6. Use the right tool for the job. Do not attempt to force a small tool or attachment to

do the work of a larger industrial tool. There are certain applications for which this tool
was designed. Do not modify this tool and do not use this tool for a purpose for which
it was not intended.

7. Dress properly. Do not wear loose clothing or jewelry as they can be caught in

moving parts. Protective, electrically non-conductive clothes and non-skid footwear
are recommended when working. Wear restrictive hair covering to contain long hair.

REV 08/06

SKU 47274 For technical questions, please call 1-800-444-3353. Page 2

8. Use eye and ear protection. Always wear ANSI approved impact safety goggles.

Wear an ANSI approved respirator when working around metal, wood, and chemical
dusts, mists, paints, oils, sealers, and stains.

9. Do not overreach. Keep proper footing and balance at all times. Do not reach over or

across running machines.

10. Maintain tools with care. Keep tools clean for better and safer performance. Follow

instructions for lubricating and changing accessories. Inspect tool cords periodically
and, if damaged, have them repaired by an authorized technician. The handles must
be kept clean, dry, and free from oil and grease at all times.

11. Avoid unintentional starting. Be sure the switch is in the Off position when not in

use and before plugging in. Do not carry any tool with your finger on the trigger,
whether it is plugged in or not.

12. Stay alert. Watch what you are doing, use common sense. Do not operate any tool

when you are tired.

13. Check for damaged parts. Before using any tool, any part that appears damaged

should be carefully checked to determine that it will operate properly and perform its
intended function. Check for alignment and binding of moving parts; any broken parts
or mounting fixtures; and any other condition that may affect proper operation. Any
part that is damaged should be properly repaired or replaced by a qualified
technician. Do not use the tool if any switch does not turn On and Off properly.

14. Guard against electric shock. Prevent body contact with grounded surfaces such as

pipes, radiators, ranges, and refrigerator enclosures.

15. Replacement parts and accessories. When servicing, use only identical

replacement parts. Use of any other parts will void the warranty. Only use accessories
intended for use with this tool. Approved accessories are available from Harbor
Freight Tools.

16. Do not operate tool if under the influence of alcohol or drugs. Read warning

labels on prescriptions to determine if your judgment or reflexes are impaired while
taking drugs. If there is any doubt, do not operate the tool.

17. Use proper size and type extension cord. If an extension cord is required, it must

be of the proper size and type to supply the correct current to the tool without heating
up. Otherwise, the extension cord could melt and catch fire, or cause electrical
damage to the tool. This tool requires use of an extension cord of 0 to 10 amps
capability (up to 50 feet), with wire size rated at 18 AWG. Longer extension cords
require larger size wire. If you are using the tool outdoors, use an extension cord
rated for outdoor use (signified by “WA” on the jacket).

18. Maintenance. For your safety, maintenance should be performed regularly by a

qualified technician.

19. WARNING: This product contains or, when used, produces a chemical known to the
State of California to cause cancer and birth defects or other reproductive harm.

- An example of these chemicals is lead from lead-based paints.

SKU 47274 For technical questions, please call 1-800-444-3353. Page 3