Page 1
TABLE STAND
FOR USE WITH 10” TILE SAW, SKU #95385
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
Copyright © 2001 by Harbor Freight Tools. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
46310
®
Note: Tile Saw shown is
not included with this
product, but is available for
purchase through Harbor
Freight Tools.
REV 01/07
Page 2
SKU 46310 Page 2
Specifications
Save This Manual
You will need the manual for the safety warnings and precautions, assembly
instructions, operating and maintenance procedures, parts list and diagram. Keep
your invoice with this manual. Write the invoice number on the inside of the front
cover. Keep the manual and invoice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING: When using this product, basic safety precautions should always
be followed to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this product!
1. Keep work area clean. Cluttered areas invite injuries.
2. Keep children away. Children must never be allowed in the work area. Do
not let them handle machines, tools, or extension cords.
3. Do not force product. It will do the job better and more safely at the rate
for which it was intended. Do not use inappropriate attachments in an
attempt to exceed the product capacity.
4. Use the right product for the job. Do not modify this product and do not
use this product for a purpose for which it was not intended.
5. Use eye and ear protection. Always wear ANSI approved impact safety
goggles.
6. Maintain with care. Inspect product periodically. If any part apprears broken
or damaged, have a qualified technician perform the necessary repairs.
7. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use
accessories intended for use with this product. Approved accessories are
available from Harbor Freight Tools.
Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution
are factors which cannot be built into this product, but must be supplied by
the operator.
ITEM
Materials
Net Weight
DESCRIPTION
Low Carbon Steel, Cast Aluminum
19 Lbs.
REV 02/06
Page 3
SKU 46310 Page 3
Unpacking
When unpacking, check to make all parts listed on Page 4 are included.
If any parts are missing or broken, please call Harbor Freight Tools at the number
on the cover of this manual.
Assembly
1. Attach the two Wheel/Brake Assemblies [2] to the Rear Saw Stand [1-2] as
shown in the Assembly Diagram on Page 4. Secure using the hardware
provided with each Assembly. Tighten Bolts fully.
2. Attach the Saw Stand to the Saw Frame Assembly [4, not included] using
the two Stand Knobs [3] in the location shown in the Diagram. Be sure to
tighten Knobs fully.
3. Carefully follow the Assembly and Operation Instructions for the 10” Tile
Saw, SKU #95385, which is intended for use with this product. The Tile Saw is
sold separately, and available for purchase through Harbor Freight Tool
Company.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER
NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO
THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE
PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE
PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS
OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
REV 01/07
Page 4
SKU 46310 Page 4
Parts List
Assembly Drawing
DESCRIPTION
Front Saw Stand
Rear Saw Stand
Wheel/Brake Assembly
(w/4 bits, washers and nuts each)
Stand Knobs
Saw Frame Assembly (not included)
ITEM
1-1
1-2
2
3
4
QTY
1
1
2
2
1
NOTE: Some parts are listed and
shown for illustration purposes
only and are not available
individually as replacement parts.
REV 01/07
Loading...