Page 1
PNEUMAPNEUMA
®
PNEUMA
PNEUMAPNEUMA
TIC ROLLER SEATIC ROLLER SEA
TIC ROLLER SEA
TIC ROLLER SEATIC ROLLER SEA
45342
ASSEMBLY AND OPERATING INSTRUCTIONS
TT
T
TT
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our W eb site at http://www.harborfreight.com
Copyright © 2001 by Harbor Freight Tools®. All rights reserved. No por tion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.
Revised Cover 12/04
Page 2
Specifications
ITEM
Overall Dimensions
Tool Tray
Lifing Pole
Ram Extension
Handle
Hub
Supporting Plate
Casters
Seat
Material
Net Weight
Weight Capacity
19-1/2”H x 15” Dia.
15” Dia. x 7/8”D x 9/100” Thick
1-31/32” Dia. x 7” to 11-5/8”H
4-1/2”
5-1/4”L x 1-1/4”W x 5/8”Thick
1-47/64” Dia. x 1-1/4”H
7-5/8” Dia.
2-27/64” Dia. x 53/64”W
11-1/2” Dia. x 1-5/8” Thick
Stamped Steel, Red Vinyl, Foam Rubber
12.35 Lbs.
300 Lbs.
DESCRIPTION
Save This Manual
You will need the manual for the safety warnings and precautions, assembly
instructions, operating and maintenance procedures, parts list and diagram.
Keep your invoice with this manual. Write the invoice number on the inside of the
front cover. Keep the manual and invoice in a safe and dry place for future
reference.
Safety Warnings and Precautions
WARNING: When using product, basic safety precautions should always be
followed to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this product!
1. Keep work area clean. Cluttered areas invite injuries.
2. Keep children away. Children should not be allowed in the work area.
3. Use the right product for the job. There are certain applications for which
this product was designed. Do not modify this product and do not use this
product for a purpose for which it was not intended.
4. Use eye protection. Always wear ANSI approved impact safety goggles.
5. Maintain product with care. Inspect parts periodically and, if damaged,
have them repaired by an authorized technician.
6. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use
accessories intended for use with this tool. Appro v ed accessories are
available from Harbor Freight Tools.
SKU 45342 Page 2
Page 3
Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution
are factors which cannot be built into this product, but must be supplied by
the operator.
Unpacking
When unpacking, check to make sure all parts listed on Page 4 are included. If
any parts are missing or broken, please call Harbor Freight Tools at the number
on the cover of this manual.
Assembly
You will need a hammer and a crescent wrench to assemble this product.
1. Insert top of Lifting Pole [D] into the Hub [C] that has already been attached
to the Seat Cushion [A].
2. Now insert Seat Cushion and Lifting Pole assembly into the top of the Tool
Tray [E].
3. Check and tighten all fasteners as needed.
Operation/Maintenance
With its convenient tool tra y, comfortable padded seat, and non-marking wheels,
the Pneumatic Roller Seat is essential for the multi-tasking craftperson.
To lower seat, sit on the Stool and pull up on the handle until you have lowered
the seat to the desired height (See Diagram I on Page 4). To raise seat, stand
next to the Stool and pull up on the handle. Release handle when seat has risen
to the desired height.
Do not let children play on or around the Roller Seat.
Do not stand on Roller Seat or use the tool tray to carry large amounts of weight.
Do not attempt to exceed the Roller Seat’ s 300 lb capacity.
Once assembled, do not attempt to take this product apart.
Do not expose to heat. Parts of this product are under pressure.
SKU 45342 Page 3
REV 08/03
Page 4
Parts List
NO.
DESCRIPTION
A
Seat Cushion
B
Supporting Plate
C
Hub
D
Lifting Pole
E
Tool Tray
F
2-1/2” Wheel
G
Handle
H
Truss Head Bolt M6x20
I
Cap Nut
J
Lock Washer 10
K
Rivet 3x18
Assembly Drawing
QTY .
1
1
1
1
1
5
1
4
5
5
1
Diagram I, Lowering Seat
NOTE: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER
NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO
THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE
PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE
PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS
OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 45342 Page 4
Loading...