Page 1
ASH CLEANER
®
VACUUM ATTACHMENT
Model 03394
ASSEMBLY and OPERATING
INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
Copyright © 2003 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
Page 2
Specifications
Maximum Capacity 5 Gallons
Tank Dimensions 13-1/2” x 12-7/8” Deep
Flex Hose 38” L x 1-3/4” Dia.
Suction Nozzle 1-9/16” Dia. x 15” L
Clean fireplaces, stoves, and barbecues with any household vacuum cleaner.
Save This Manual
You will need the manual for the safety warnings and precautions, assembly instructions,
operating and maintenance procedures, parts list and diagram. Keep your invoice with this
manual. Write the invoice number on the inside of the front cover. Keep the manual and
invoice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING: When using pr oduct, basic safety precautions should alwa ys be followed to
reduce the risk of personal injury and damage to equipment.
Read all instructions before using this product!
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Do not use this product in damp or wet locations.
Don’t expose to rain. Keep work area well lighted. Do not use electrically powered
products in the presence of flammable gases or liquids.
3. Keep children away. Children must never be allowed in the work area. Do not let
them handle this product or they may receives bur ns from the hot canister.
4. Store idle equipment. When not in use, this product must be stored in a dry location
to inhibit rust. Always lock up this product and keep out of reach of children.
5. Use the right tool for the job. Do not attempt to force a small product or
attachment to do the work of a larger industrial product. There are certain
applications for which this product was designed. It will do the job better
and more safely at the rate for which it was intended. Do not modify this
product and do not use this product for a purpose for which it was not intended.
6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in
moving parts. Protective, electrically non-conductive clothes and non-skid footwear
are recommended when working. Wear restrictive hair covering to contain long hair.
7. Use eye and ear protection. Always wear ANSI approved impact safety goggles and
ear protection. Wear an ANSI approved dust mask or respirator when working around
dusts and mists.
8. Do not overreach. Keep proper footing and balance at all times. Do not reach over or
across running machines.
SKU 03394
Page 2
REV 04/03
Page 3
9. Maintain products with care. Keep this product clean for better and safer
performance. Inspect hoses, and if damaged, have them repaired by an authorized
technician.
10. Disconnect power. Disconnect from the vacuum (not included) when not in use.
11. Avoid unintentional starting. Be sure the switch (vacuum-not included) is in the Off
position when not in use and before plugging in.
12. Stay alert. Watch what you are doing, use common sense. Do not operate any
product when you are tired.
13. Check for damaged parts. Before using any product, any part that appears
damaged should be carefully checked to determine that it will operate properly and
perform its intended function. Check for alignment and binding of moving parts; any
broken parts or mounting fixtures; and any other condition that may affect proper
operation. Any part that is damaged should be properly repaired or replaced by a
qualified technician.
14. Guard against electric shock. Prevent body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerator enclosures.
15. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use accessories
intended for use with this product. Approved accessories are available from Harbor
Freight Tools .
16. Do not operate product if under the influence of alcohol or drugs. Read warning
labels if taking prescription medicine to determine if your judgement or reflexes are
impaired while taking drugs. If there is any doubt, do not operate the Ash Cleaner
Vacuum Attachment.
17. Maintenance. For your safety, maintenance should be performed regularly by a
qualified technician.
Warning: When using the Vacuum Attachment, the Canister (#3) must be placed
on a heat resistant surface. Hot embers and ash will result in the canister
becoming very hot.
Warning: The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be
built into this product, but must be supplied by the operator.
Unpacking
When unpacking, check to make sure the parts listed on page 6 are included. If any parts
are missing or broken, please call Harbor Freight Tools at the number on the cover of this
manual as soon as possible.
SKU 03394
Page 3
REV 02/04
Page 4
Operation
See Assembly Drawing on page 7.
1. Fit the Cover (#2) on top of the Canister (#3) so that the grooves or lips of the
Canister (#3) line up and correspond to the grooves on the edge of the Cover (#2).
See FIGURE 1.
Note: On the inside of the Cover (#2), underneath the Rubber Gasket (#5) is the Wire Cage
Filter.
FIGURE 1
Vacuum Cleaner Hose (not included) intake
Grooves on Cover (#2)
Grooves on Canister (#3)
Rubber Gasket (#5)
Ring (#1)
Flex Pipe (#4) intake
2. Fit the Ring (#1) onto both of lips of the Cover (#2) and Canister (#3).
3. Seal the cover by closing the ring lock and securing the locking clasp on the Ring (#1) as
shown in FIGURE 2.
FIGURE 2
Locking Clasp
SKU 03394
Page 4
REV 02/04
Page 5
Operation (continued)
See Assembly Drawing on page 7.
4. Insert the Nozzle (#7) into the Black T ube (#8). Twist it on securely.
5. Fit the other end of the Fle x Pipe (#4) into the the Flex Pipe ingress (See FIGURE 1) and
twist (approximately 1/4 turn) until it locks into place (bayonet type locking system).
6. Insert the Vacuum Cleaner Hose (not included) securely into the Rubber
Gasket (#5) .
Note: On the inside of the Cover (#2), underneath the Rubber Gasket (#5) is the Wire Cage
Filter. Its purpose is to keep ashes in the Canister (#3) from being sucked into the Vacuum
Cleaner Hose (not included), and damaging your vacuum. Before operation, and
periodically during operation, you must check that the filter is clear. If vacuum power
decreases, ash particles may be clogging the Wire Cage Filter. Gently tap on the
Cover (#2) and the top of the Vacuum Cleaner Hose (not included) to loosen the debr is.
If power does not increase, you will have to open the unit and clean out the filter.
Warning!! Once the unit becomes filled with ash, the metal Canister (#3) will become
very hot and you will need to be wearing thick glo ves designed to handle it. Failure to
do so may result in burns. Make sure no other people or animals come in contact with
the hot Canister (#3).
Note: Make sure the level of ash in the Canister (#3) never reaches the bottom of the Wire
Cage Filter as it will clog operation.
Warning! Make sure that the Canister (#3) sits on a flat heat resistant surface that can
tolerate excessive heat without being damaged or catching fire. This product is designed to vacuum hot ashes and embers when properly operated. The Canister (#3)
will become very hot when it is filled with hot ash and embers.
Reminder: Chec k the Wire Cage Filter often. Also, chec k the vacuum filter periodicall y
to make sure no ashes are reaching it.
7. Before turning on the vacuum (not included), make sure the fire in the fireplace or woodsto ve
is completely out. Do not attempt to vacuum when a fire is present. You will damage the
unit, the vacuum, and risk personal injury.
8. If your vacuum has variable settings, set it on the lowest setting. Switch on your vacuum
and collect the ash.
Note: If you see any ash dust escaping from any part of the main unit or hoses, immediately
shut down the vacuum and check and tighten the appropriate fittings.
Warning! If the Flex Pipe (#4) becomes too hot to hold comfortably, stop vacuuming the
ashes, allow the vacuum to run for several seconds and then turn off the vacuum and wait
until the unit is cool to the touch before continuing.
Failure to do so may result in permanent damage to the unit and the vacuum.
9. When finished, lift the Flex Pipe (#4) straight up vertically and tap the sides of it to allow
remaining ashes to be pulled into the Canister (#3).
10. Turn off the vacuum and repeat step 9 above.
11. Remove the Vacuum Cleaner Hose (not included) and the Flex Pipe (#4) from the
Cover (#2).
12. Allow the ashes to completely cool before transferring. This may take 24 to 48 hours. If
you must transfer war m or hot ashes before they have ample time to cool, make sure the
receptacle is designed to hold very, hot flammable materials.
Note: Dispose of ashes properly and safely adhering to local codes.
SKU 03394
Page 5
REV 02/04
Page 6
Parts List
Part No. Description
1 Ring
2Cover
3 Canister
4 Flex Pipe
5 Gasket
7 Nozzle
8 Black Tube
Maintenance
Note: Immediately after each use, empty your v acuum’s bag and clean the filter . Be ware that
the vacuum bag and filter may contain hot ash. Dispose of them in a safe manner.
1. Never attempt any maintenance when the unit is warm or hot to the touch, or when it is
attached to a vacuum cleaner.
2. Before operation, and periodically dur ing operation, you must check that the Wire Cage
Filter is clear.
3. Bef ore assembling the unit, mak e sure that the lip or grooves on the Co ver (#2) and on top
of the Canister (#3) are clean and clear of any debris.
4. All fittings must be cleaned before and after each use.
THE MANUF ACTURER AND/OR DISTRIBUT OR HAS PRO VIDED THE PARTS DIA GRAM IN THIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTA TION OR W ARRANTY OF ANY KIND T O THE BUYER THAT HE
OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STA TES THA T ALL REPAIRS AND P AR TS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NO T BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PAR TS THERET O , OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERET O .
NOTE: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
SKU 03394
PLEASE READ THE FOLLOWING CAREFULLY
Page 6
REV 02/04
Page 7
Assembly Drawing
Hose From Vacuum (not inc luded)
Wire Cage Filter
SKU 03394
Page 7
Loading...