Harbor Breeze E-BDB52ABZC5BC4N, E-BDB52BNK5BC4N, E-BDB52LW5BC4N, E-BDB52MBK5BC4N Owner's Manual

Harbor Breeze® is a registered trademark
of LF, LLC. All Rights Reserved.

ITEM #0152426

0156738
0158620
0204925

SPRINGFIELD II CEILING FAN

MODEL #E-BDB52ABZC5BC4N

E-BDB52BNK5BC4N

E-BDB52LW5BC4N

E-BDB52MBK5BC4N

Español p. 22

Federal regulations require ceiling fans with light kits manufactured or imported after
January 1, 2009, to limit total wattage consumed by the light kit to 190W. Therefore,
this fan is equipped with a wattage limiting device.

ATTACH YOUR RECEIPT HERE

Serial Number

Questions, problems, missing parts? Before returning to your retailer, call or contact our
customer service department at 1-800-527-1292, 8:30 a.m. - 5:00 p.m., CST, Monday - Friday.

LISTED

E192641

Purchase Date

1

TABLE OF CONTENTS

Safety Information .....................................………………………………………………...…

….....

Product Overview ...........................................................................................................................4

2 - 3

Package Contents .....……………………………………………………………..….

Hardware Contents ...................................................................................................................

….

.........

......

......

Preparation ...............….…………………..……………………….…………….……………….......6

Initial Installation ............….……………..……………………….……….

…..….

.............................7 - 8

Downrod Style Fan Mounting ............................................................................................8 - 10

Closemount Style Fan Mounting

.

...........................................................................................10 - 11

Wiring .................................……………………........................................…………...........12 - 13

Final Installation ….…………….……………………….…………….……..........

Operation Instructions ............................................................……………………

Care and Maintenance …

….…

…………………………………………………..….......

Troubleshooting .............………...………………………….……………..………....

Warranty ……………………………….…………………………………………..…

.....….......

………............

..............

…........19 - 20

….

.........

14 - 17

17 - 18

19

........

20

5
6

Replacement Parts List ...........................................................................................

.........

...................

21

SAFETY INFORMATION

READ AND SAVE THESE INSTRUCTIONS
Please read and understand this entire manual before attempting to assemble, install or operate the
product. If you have any questions regarding the product, please call customer service at
1-800-527-1292, 8:30 a.m. - 5:00 p.m., CST, Monday - Friday.

• Do not discard fan carton or foam inserts. Should this fan need to be returned to the factory for
repairs, it must be shipped in its original packaging to ensure proper protection against damage that
might exceed the initial cause for return.

• Make sure that all electrical connections comply with local codes, ordinances, the National Electrical

Code and ANSI/NFPA 70-1999. Hire a qualified electrician or consult a do-it-yourself wiring handbook
(available at Lowe's) if you are unfamiliar with installing electrical wiring.

• Make sure the installation site you choose allows a minimum clearance of 7 feet from the blades to

the floor and at least 30 in. from the end of the blades to any obstruction.

• After you install the fan, make sure that all connections are secure to prevent the fan from falling.

• The net weight of this fan including the light kit is: 19.62 lbs. (8.9 kg).

2

SAFETY INFORMATION

WARNINGS

To reduce the risk of fire, electrical shock, or personal injury, mount fan to outlet box

marked "ACCEPTABLE FOR FAN SUPPORT OF 35 LBS (15.9 KG) OR LESS" and use
mounting screws provided with the outlet box. Most outlet boxes commonly used for the
support of lighting fixtures are not acceptable for fan support and may need to be replaced.
Consult a qualified electrician if in doubt.

When mounting fan to a ceiling outlet box, use a METAL octagonal outlet box. Secure the outlet
box directly to the building structure. The outlet box and its support must be able to support the
moving weight of the fan (at least 35 lbs.). Do NOT use a plastic outlet box.

To avoid personal injury, the use of gloves may be necessary while handling fan parts with
sharp edges.

To reduce the risk of fire, electrical shock, or personal injury, wire connectors provided with this
fan are designed to accept only one 12-gauge house wire and two lead wires from the fan. If your
house wire is larger than 12-gauge or there is more than one house wire to connect to the two fan
lead wires, consult an electrician for the proper size wire connectors to use.

To reduce the risk of fire or electrical shock, do not use the fan with any solid state speed
control device or control fan speed with a full range dimmer switch.

To reduce the risk of fire, electrical shock, or personal injury, do not bend the blade arms when
installing them, balancing the blades, or cleaning the fan. Do not insert objects between the
rotating fan blades.

To reduce the risk of personal injury, use only parts provided with this fan. The use of parts

OTHER than those provided with this fan will void the warranty.

CAUTIONS

Before proceeding, be sure to shut off electricity at main switch or circuit breaker in order to avoid
electrical shock.

Read all instructions and safety information before installing your new fan. Review the
accompanying assembly diagrams.

3

PRODUCT OVERVIEW

Congratulations on your purchase of this Harbor Breeze®
Ceiling Fan! This product has been specifically designed to
give you all the performance you’ll ever need. Harbor Breeze®
is the perfect fusion of smart innovation and beautiful style.
Designed for more than just air movement, our products are
built to function flawlessly... day after day. Expect showroom
quality at an exceptional price with Harbor Breeze® - available
exclusively at Lowe’s.

Harbor Breeze® is a registered trademark
of LF, LLC. All Rights Reserved.

Determining how you want your ceiling fan to look and operate is an important step prior to
installation. You can save installation time by deciding which options are best suited for your needs
before beginning the steps outlined in this manual.

Your fan can be installed with or without a downrod.

• Downrod-style mounting is best suited for ceilings 8 ft. (2.44 m) high or higher. For taller ceillings
you may want to use a longer downrod (sold separately) than the one provided.

• Angle-style mounting is best suited for angled or vaulted ceilings. A longer downrod is sometimes
necessary to ensure proper blade clearance.

• Closemount-style mounting is more suitable for ceilings lower than 8 ft. (2.44 m) high.
Your fan also has multiple wiring options available, including:

• Fan and light controlled by pull chain.

• Fan controlled by pull chain, light controlled by wall switch.

• Fan and light controlled by two separate wall switches.
Your fan is remote control adaptable (remote control sold separately).

4

PACKAGE CONTENTS

B

A

P

C

R

D

O

I

M

T

S

L

PART DESCRIPTION QUANTITY

A
B
C
D
E*
F
G
H
I
J

Downrod 1
Canopy
Mounting Bracket
Motor Housing
Plastic Locking Mechanism
Light Kit Fitter
Blade
Blade Arm
Glass Shade
Candelabra Base Bulb

K Pull Chain Extension 2

J

1
1
1
5
1
5
5
4
4

L Socket Ring 4
(preassembled)

M Motor Screw 10

(preassembled)

* US Pat. No. 7351037

Q

E

*

H

N

H

F

U

K

PART DESCRIPTION QUANTITY

N

Switch Housing Cap

(preassembled)
O

Lock Washer

10

(preassembled)
P

Canopy Mounting Screw

(preassembled)
Q
R Clip (preassembled)
S Light Kit Fitter Screw

IMPORTANT REMINDER: You must

Pin (preassembled)

(preassembled)

T Switch Housing Screw

(preassembled)

U Blade Screw 15

(preassembled)

use the parts provided with this fan for
proper installation and safety.

G

1

4

1
1
3

3

5

HARDWARE CONTENTS (shown actual size)

AA

E3 Wire
Connector

Qty. 4

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with “Package

Contents” list and diagrams on the previous page. If any part is missing or damaged, do not attempt
to assemble the product. Contact customer service for replacement parts.

Estimated Assembly Time: 120 minutes

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety
Glasses, Stepladder and Wire Strippers

Helpful Tools (not included): AC Tester Light, Tape Measure, Do-It-Yourself Wiring Handbook
(available at Lowe’s) and Wire Cutters

Bulbs Required (included): 4 candelabra-base 40-watt max. bulbs

DANGER: When using an existing outlet box, make sure the outlet box is securely attached to

the building structure and can support the full weight of the fan. Failure to do this can result in serious
injury or death. The stability of the outlet box is essential in minimizing wobble and noise in the fan
after installation is complete.

CAUTION: Be sure outlet box is properly grounded and that a ground wire (green or bare) is
present.

After opening top of carton, remove mounting hardware package from foam inserts. Remove motor
from packing and place on carpet or on foam to avoid damage to finish.

CAUTION: Carefully check all screws, bolts and nuts on fan motor assembly to ensure that they
are secured.

6

INITIAL INSTALLATION

1.

Turn off circuit breakers and wall switch to the fan
supply line leads. (Fig. 1)

DANGER: Failure to disconnect power supply
prior to installation may result in serious injury or
death.

2.

Determine mounting method to use. (Fig. 2)
A. Downrod mount (normal or angled ceiling)
B. Closemount (normal ceiling only)
Important: If using the angle mount, check to
make sure the ceiling angle is not steeper than 19°.

1

2

ON

ON

OFF

OFF

Check to make sure blades (G) are at least 30 in.

3.
from any obstruction. Check downrod (A) length to
ensure blades (G) are at least 7 ft. above the floor.
(Fig. 3)

3

G

A

B

30 in.

min.

7 ft.
min.

7

INITIAL INSTALLATION

Secure mounting bracket (C) to outlet box using

4.
screws, spring washers, and flat washers
provided with the outlet box. (Fig. 4)
*NOTE: It is very important that you use the

proper hardware when installing the mounting
bracket (C) as this will support the fan.

4

IMPORTANT: If using the angle mount, make

sure open end of mounting bracket (C) is installed
facing the higher point of the ceiling.

5.

Remove motor screws (M) and lock washers (O)
from underside of motor. [If there are plastic
motor blocks installed with the motor screws (M)
and lock washers (O), discard the plastic motor
blocks.] (Fig. 5)

Follow mounting instructions on pages 8 - 10 for
“Downrod Style Fan Mounting” or proceed to
pages 10 and 11 for “Closemount Style Fan
Mounting”, depending on mounting method (A or
B) chosen in Step 2 on previous page.

C

5

O

M

DOWNROD STYLE FAN MOUNTING

1.

Remove pin (Q) and clip (R) from motor housing
yoke at top of motor housing (D) and partially loosen
set screws. (Fig. 1)

*Helpful Hint: Downrod style mounting is best
suited for ceilings 8 ft. (2.44 m) high or higher. For
taller ceilings you may want to use a longer downrod
(not included) than the one provided. Angle style
mounting is best suited for angled or vaulted
ceilings. A longer downrod is sometimes necessary
to ensure proper blade clearance.

1

R

D

8

Set
Screw

Q

DOWNROD STYLE FAN MOUNTING

2.

Insert downrod (A) through canopy (B). Thread
wires from motor housing (D) through downrod
(A). (Fig. 2)

3.

Slip downrod (A) into motor housing yoke, align
holes and re-install pin (Q) and clip (R).
Re-tighten set screws in motor housing yoke
and then tighten nuts. (Fig. 3)

2

A

B

3

A

Depending on the length of downrod (A) you

4.
use, you may need to cut the lead wires back to
simplify the wiring. If you decide to cut back the
lead wires, it is suggested that you do so in the
following manner:

Take the lead wires and make sure that you
have pulled them all the way through the top of
the downrod (A). Start at the TOP of the ball on
the downrod (A) and measure 8 in. of lead wire,
and then cut the excess wire off with wire cutters
(not included). (Fig. 4)

4

R

Set
Screw

Q

Ball

NOTE: If you do not cut back the lead wires,
Steps 4 and 5 are not necessary and you may
proceed to Step 6 instead.

A

9

DOWNROD STYLE FAN MOUNTING

5.

If you decided to cut back the lead wires in Step
4, strip 1/2 in. of insulation from end of white
wire. Twist stripped ends of each strand of wire
within the insulation with pliers (not included).
(Fig. 5) Repeat Step 5 for black, blue (if
applicable) and green wires.

6.

Install ball end of downrod (A) into mounting
bracket (C) opening. Align slot in ball with tab in
mounting bracket (C). (Fig. 6)

5

6

DANGER: Failure to align slot in ball with tab
may result in serious injury or death.

Continue to "Wiring" instructions on page 12.

CLOSEMOUNT STYLE FAN MOUNTING

1.

Remove canopy cover from bottom of canopy (B).
(Fig. 1) [Note: It may be necessary to use the
handle end of a screwdriver (not included) to
remove the canopy cover by tapping on the
canopy cover from the inside of the canopy (B).]

*Helpful Hint: Closemount style mounting is
more suitable for ceilings lower than 8 ft. (2.44 m)
high. The downrod (A), hanging ball, and canopy
cover are not used in this type of installation.

C

Tab

Slot

A

1

B

Canopy
Cover

10

CLOSEMOUNT STYLE FAN MOUNTING

If neccessary, remove every other screw and lock

2.
washer from top of motor housing (D). (If there are
only three screws and lock washers in top of motor
housing (D), the other three screws and lock
washers will be located in one of the hardware
packs.) (Fig. 2)

Remove pin (Q), clip (R) and set screws from
motor housing yoke. (Fig. 2)

Pull wires through hole in the middle of the canopy

3.
(B) and attach canopy (B) to motor housing (D)
using the three screws and three lock washers
referred to in step 2 above. (Fig. 3)

2

D

3

B

4.

Hang motor housing (D) on the tab on the
mounting bracket (C) using one of the
non-slotted holes in the canopy (B). (Fig. 4)

D

4

C

Tab

B

D

11

WIRING

WARNING: To reduce the risk of fire, electrical
shock, or personal injury, wire connectors provided
with this fan are designed to accept only one
12-gauge house wire and two lead wires from the
fan. If your house wire is larger than 12-gauge or
there is more than one house wire to connect to the
two fan lead wires, consult an electrician for the
proper size wire connectors to use.

CAUTION: Be sure outlet box is properly grounded
and that a ground (green or bare) wire is present.

WARNING: If house wires are different colors
than referred to in the following steps, stop
immediately. A professional electrician is
recommended to determine wiring.

1.

Choose wiring diagram (Fig. 1A, Fig. 1B or Fig. 1C)
that fits your situation and make appropriate wiring
connections as follows: [NOTE: For each wire
connection below, use one of the wire connectors
(AA) provided, making sure to screw wire
connector (AA) on in a clockwise direction.]

1A. FAN AND LIGHT CONTROLLED BY PULL
CHAINS: Connect BLACK and BLUE wire from
fan to BLACK wire from ceiling. Connect WHITE
wire from fan to WHITE wire from ceiling.
Connect all GROUND (GREEN) wires together
from fan (on downrod (A) and mounting bracket
(C)) to BARE/GREEN wire from ceiling. (Fig. 1A)

1B. FAN CONTROLLED BY PULL CHAIN,
LIGHT BY WALL SWITCH: If you intend to
control the fan light with a separate wall switch,
connect BLACK wire from fan to BLACK wire
from ceiling. Connect BLUE wire from fan to the
BLACK wire from the independent wall switch
for the light. Connect WHITE wire from fan to
WHITE wire from ceiling. Connect all GROUND
(GREEN) wires together from fan (on downrod
(A) and mounting bracket (C)) to

BARE/GREEN wire from ceiling. (Fig. 1B)

FAN AND LIGHT CONTROLLED BY PULL CHAINS

1A

120 V Power

FROM

CEILING

FAN

GREEN

FAN CONTROLLED BY PULL CHAIN, LIGHT BY
WALL SWITCH

1B

120 V Power

FROM

CEILING

BLUE

BLACK

BLACK

WHITE
GROUND/GREEN (BARE)

WHITE

GREEN

BLACK

BLUE

WHITE

FROM FAN

BLACK

BLACK (WALL SWITCH)

WHITE

GROUND/GREEN (BARE)

WHITE

GREEN

12

FAN

GREEN

FROM FAN

WHITE

WIRING

1C. FAN AND LIGHT CONTROLLED BY
TWO WALL SWITCHES: If you intend to
control the fan and light with separate wall
switches, connect BLACK wire from fan to
BLACK wire from the independent wall switch
for the fan. Connect BLUE wire from fan to the
BLACK wire from the other independent wall
switch for the light. Connect WHITE wire from
fan to WHITE wire from ceiling. Connect all
GROUND (GREEN) wires together from fan
(on downrod (A) and mounting bracket (C)) to

BARE/GREEN wire from ceiling. (Fig. 1C)

NOTE: Black wire is hot power for fan. Blue wire

is hot power for light kit. White wire is common
for fan and light kit. Green or bare wire is ground.

2.

Wrap electrical tape (not included) around each
individual wire connector (AA) down to the wire as
shown in Fig. 2.

FAN AND LIGHT CONTROLLED BY TWO WALL
SWITCHES

1C

120 V Power

FROM

CEILING

BLACK

FAN

GREEN

BLACK (WALL SWITCH)

BLACK (WALL SWITCH FOR LIGHT)

WHITE

GROUND/GREEN (BARE)

BLUE

GREEN

FROM FAN

WHITE

WHITE

2

WARNING: Make sure no bare wire or wire
strands are visible after making connections. Place
green and white connections on opposite side of box
from the black and blue (if applicable) connections.

Turn spliced/taped wires upward and gently push
wires and wire connectors (AA) into outlet box.

Hardware Used

AA

E3 Wire Connector x4

3.

IMPORTANT: Using a full range dimmer switch
(not included) to control fan speed will cause a
loud humming noise from fan. To reduce the risk
of fire or electrical shock, do NOT use a full
range dimmer switch to control fan speed. (Fig.

3)

AA

3

AA

3
2

1

CC

AA

13

Dimmer
Switch

Speed
Switch

For illustrative purposes only--not

intended to cover all types of controls