Harbor Breeze 35063 Installation Manual
ITEM #0428802
CEILING FAN
MODEL #35063
Français p. 11
ATTACH YOUR RECEIPT HERE
Serial Number
Questions, problems, missing parts? Before returning to your retailer, call our
customer service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday - Thursday,
8 a.m. - 5 p.m., EST, Friday.
Purchase Date
1
PACKAGE CONTENTS
E
S
G
D
A
H
I
F
N
R
B
P
C
J
K
L
O
Q
M
PART DESCRIPTION QUANTITY
A
B
C
D
E
F
G
H
I
J
K
Hanging Bracket 1
Hair Pin 1
Clevis Pin 1
Down Rod 1
Canopy 1
Canopy Hole Cover 1
Motor Coupling Cover 1
Motor Assembly 1
Blade Housing 1
Light Housing 1
Blade Screws 20
L
M
N
O
P
Q
R
S
Blade 5
Shade 1
Shade Housing Screws 3
Light Housing Screws 3
Blade Washers 20
Bulb 1
Blade Iron 5
Blade Iron Screws 10
2
Lowes.com/harborbreeze
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the
product. If you have any questions regarding the product, please call customer service at
1-800-643-0067, 8 a.m. - 4:30 p.m., EST.
WARNING:
• Important: When using an existing outlet box, be sure the box is securely attached to the building
structure and can support the full weight of the fan. Failure to do so can result in serious injury or
death.
• Turn off circuit breakers and wall switch to the fan supply wire leads. Warning: Failure to
disconnect power supply prior to installation may result in serious injury or death.
• Do not install fan on a ceiling with a pitch greater than 20°.
• Installation work and electrical wiring must be done by qualified person(s) in accordance with all
applicable codes and standards (ANSI/NFPA 70-1999). If you are unfamiliar with the wiring
codes, contact a qualified electrician.
• Important: Be sure wiring box is properly grounded or that a ground (green) wire is present.
• Make sure the installation site you choose allows a minimum of 7 feet from the floor to the end of
the blades
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and diagram. If any part is missing or damaged, do not attempt to assemble the product.
Contact customer service for replacement parts.
Estimated assembly time: 30 minutes to 1 hour.
Tools Required for Assembly (not included): Phillips screwdriver, flathead screwdriver, wire strippers,
electrical tape, ladder, safety glasses, silicone caulk, caulking gun.
ASSEMBLY INSTRUCTIONS
• Most outlet boxes commonly used for the support of luminaires may not be acceptable for fan
support and may need to be replaced. Consult a qualified electrician if in doubt. Use only UL/ETL
Listed outlet boxes marked FOR FAN SUPPORT. Do not use plastic outlet boxes.
• Warning-Risk of fire, electric shock, or personal injury. Ceiling fans may be either directly
supported from a structural framing member of a building and (see examples in figures A & B) or
may be mounted to an outlet box marked acceptable for fan support of 31.8 kg (70 lbs) or less
(see example in figure C).
A B C
3
Lowes.com/harborbreeze
ASSEMBLY INSTRUCTIONS
1. Secure the hanger bracket (A) to the ceiling outlet
box using screws and washers provided with the
outlet box. Important: If attaching the fan to a sloped
ceiling, make sure open end of mounting bracket is
installed facing the roof. Do not install fan on a
ceiling with a pitch greater than 20°.
2
1
A
JH
DD
EEEEEEEB
DC
GE
JF
G
2. Remove the hairpin (B) clip and clevis pin (C) from the downrod support of the motor assembly
(H) and loosen the two set screws. Slide the downrod (D) through the canopy (E), canopy hole
cover (F) and motor coupling cover (G). Feed the black and white and blue wires from fan
through the downrod (D). Insert the downrod into motor assembly (H) Secure clevis pin (C) with
hairpin (B) clip and tighten setscrews.
4
Lowes.com/harborbreeze
ASSEMBLY INSTRUCTIONS
3. Loosen the two shoulder screws without fully
removing from the hanging bracket (A). Carefully lift
the fan and seat the downrod (D)/hanger ball
assembly on the hanger bracket (A) that was just
attached to the outlet box. Be sure the groove in the
ball is lined up with the tab on the hanger bracket
(A).
3
EEEUEEEA
EEEUEEED
4. For Canadian installation and for USA fans over 35
lbs, the safety cable must be installed into the house
structure beams using a 3” lag screw. Make sure
that when the safety cable is fully extended the
leadwires are longer than the cable and no stress is
placed on the lead.
4
Safety
Cable
Safety
Cable
Safety
Cable
5
Lowes.com/harborbreeze
ASSEMBLY INSTRUCTIONS
5
5. Wring the fan per wiring diagram and Securely connect wires with wire connectors:
• Connect WHITE fan motor wire to WHITE supply wire.
• Connect BLACK and BLUE fan wires to BLACK supply wire.
• Connect GROUND (GREEN) wires from hanger bracket and downrod ball, to GROUND (GREEN
or BARE COPPER) from house.
6
Lowes.com/harborbreeze
Loading...