Harbor Breeze 00873, 00874, 00875 User Manual
1
MAZON CEILING FAN
ITEM #0464467, 0464468, 0464469
MODEL #00873, 00874, 00875
ETL MODEL #44-MZ
Español p. 16
Serial Number
Purchase Date
Harbor Breeze ® is a registered trademark of LF,
LLC. All Rights Reserved.
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday - Thursday,
8 a.m. - 5 p.m., EST, Friday.
ATTACH YOUR RECEIPT HERE
Lowes.com/harborbreeze
EB 14191
32
TABLE OF CONTENTS
Safety Information............................................................................................................... 3
Package Contents............................................................................................................... 4
Hardware Contents............................................................................................................. 5
Preparation.......................................................................................................................... 5
Assembly Instructions......................................................................................................... 6
Operating Instructions.......................................................................................................... 11
Care and Maintenance........................................................................................................ 13
Troubleshooting................................................................................................................... 14
Warranty.............................................................................................................................. 15
Replacement Parts List ...................................................................................................... 15
3
Lowes.com/harborbreezeLowes.com/harborbreeze
SAFETY INFORMATION
READ AND SAVE THESE INSTRUCTIONS
Please read and understand this entire manual before attempting to assemble, operate, or install
the product.
• When using an existing outlet box, be sure the box is securely attached to the building structure
and can support the full weight of the fan, so as to avoid potential serious injury or death.
• All wiring must be in accordance with the National Electrical Code “ANSI/NFPA 70-1999”
and local electrical codes. Electrical installation should be performed by a qualied licensed
electrician.
• DO NOT use bulbs with a wattage greater than the maximum value stated on the xture and in
this manual. Using a higher wattage bulb than specied will increase xture temperature and
cause risk of re.
• Disconnect the electrical supply circuit to the fan before installing light kit.
• Electrical diagrams are for reference only.
• The net weight of this fan including the light kit is: 15.62 lbs.
WARNING
• ELECTRIC SHOCK HAZARD - To reduce the risk of electric shock, do not use this fan with any
solid-state speed control device.
• ELECTRIC SHOCK HAZARD - To reduce the risk of electric shock, make sure electricity has
been turned off at the circuit breaker or fuse box before beginning installation.
• PERSONAL INJURY HAZARD - To reduce the risk of injury to persons, install fan so that the
blade is at least 7 ft. above the oor.
• ELECTRIC SHOCK HAZARD - Do not install this fan with wall-mounted solid-state speed
control or wall-mounted light-dimmer control. It will permanently damage the fan’s remote control
receiver and cause the fan’s functions to fail.
• FIRE, ELECTRIC SHOCK OR PERSONAL INJURY HAZARD - To reduce the risk of re,
electric shock, or personal injury, mount to outlet box marked “ACCEPTABLE FOR FAN
SUPPORT OF 35.1 lbs OR LESS” and use mounting screws provided with the outlet box. Most
outlet boxes commonly used for the support of lighting xtures are not acceptable for fan support
and may need to be replaced. Consult a qualied electrician if in doubt.
CAUTION
• PERSONAL INJURY HAZARD - Reduce the risk of personal injury, do not bend the blade
brackets when installing the brackets, balancing the blades, or cleaning the fan. DO NOT insert
foreign objects in between rotating fan blades.
54
PREPARATION
HARDWARE CONTENTS (shown actual size)
BB
N
AA
Wire Connector
Qty. 4
Blade Screw
Qty. 10
PACKAGE CONTENTS
B
A
F
G
H
D
I
J
K
L
M
PART DESCRIPTION QUANTITY
A Mounting Plate 1
B Fan Motor 1
C Trim Ring 1
D Blade 3
E Enhance Plate 3
F Light Plate 1
G Light Fixture 1
H Switch Housing Plate (preassembled to Fan Motor (B)) 1
I Bulb 1
J Glass 1
K Remote Control 1
L Battery 1
M Wall Bracket 1
E
C
Lowes.com/harborbreezeLowes.com/harborbreeze
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 45 minutes
Tools Required for Assembly (not included): Phillips screwdriver, step ladder, electrical tape, pliers,
wire cutters, wire strippers.
CC
Remote Control
Screw
Qty. 2
R
N Rubber Shipping Stabilizer Tab (preassembled to fan motor (B)） 3
6 7
ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS
1
4
5
3
6
1. Attach mounting plate (A) to outlet box (not included)
using two screws (not included). Securely tighten two
outlet box screws. Pull black, white, and grounded
wires out of outlet box and through the hole in the
mounting plate (A).
2. Place trim ring (C) over canopy, and lay it on fan
motor (B).
3. Loosen two preassembled screws across from each
other on the mounting plate (A). Remove and save
remaining two preassembled screws. Hang fan motor (B)
on mounting plate (A) hook using one of the non-slotted
holes in the canopy.
4. Connect BLACK wire from fan to BLACK wire from
ceiling. Connect WHITE wire from fan WHITE wire
from ceiling. Connect all GROUNDED (GREEN) wires
together from fan GREEN/GROUNDED wire from ceiling.
Connecting the GREEN/GROUNDED wires is conducive
to receive the signal of the remote control.
Note: Black wire is hot power for fan and light kit. White
wire is common for fan and light kit. Green wire is
grounded wire. lf house wires are different colors
than referred to above, stop immediately and consult a
professional electrician to determine proper wiring.
6. Align keyholes on fan motor (B) with protruding screw
heads on mounting plate (A). Lift fan motor (B) up to
mounting plate (A), making sure not to break any wire
connection. Rotate clockwise until screw heads fully
engage into keyholes. Insert previously removed screws
(Step 3, page 6) and securely tighten all screws.
A
A
B
B
B
A
C
B
Outlet box
Screw
2
Hardware Used
x 4
Wire Connector
AA
AA
Canopy
Canopy
Screw
Hook
Grounded/
Green
White
Black
outlet box
black
white
green
white
GREEN/
GROUNDED
black
Supply circuit
receiver
Screw
Lowes.com/harborbreezeLowes.com/harborbreeze
5. Twist wire ends together and screw wire connectors (AA)
on in a clockwise direction. Tape wire connectors (AA)
and wires together.
Note: Wires should be spread apart with grounded
conductor and equipment-grounding conductor on one
side of outlet box and ungrounded conductor on other
side. After making connections, make sure bare wire
or wire strands are NOT visible. Place green and white
connections on opposite side of box from black and
blue connections. Splices should be turned upward and
pushed carefully up into outlet box.
Black
Black
White
Green
Outlet box
Green/
Grounded
Receiver
White
8 9
ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
11
9
7. Align notches on fan motor (B) canopy with raised
areas on inside of trim ring (C). Pop trim ring (C) into
the canopy.
8. Remove and discard preassembled rubber shipping
stabilizer tabs (N) from fan motor (B). Insert blade
(D) into slot on fan motor (B). Secure blade (D) with
enhance plate (E) and three blade screws (BB). Repeat
for remaining blades (D), enhance plates (E) and blade
screws (BB).
10. Insert wires from fan motor (B) through middle hole in
light plate (F). Attach light plate (F) to switch housing
plate (H). Align keyholes then twist to lock. Replace
previously removed screw (Step 9, page 8) and
securely tighten all screws.
11. Loosen two preassembled screws from light plate (F).
Remove and save remaining preassembled screw
from light plate (F).
12. Connect WHITE wire from light plate (F) to WHITE
BLUE wire from
light plate (F) to BLACK
and twist to lock. Replace previously removed screw
(Step 11, page 9) and securely tighten all screws.
9. Loosen two screws from switch housing plate (H).
Remove and save remaining screw.
7
8
E
JJ
D
`
10
12
B
B
E
N
BB
D
H
C
KK
Screw
H
Canopy
Notch
Raised
area
Hardware Used
BB
N
Blade Screw x 10
Slot for
blade insert
Keyslot hole
Screw
Screw
Screw
B
F
F
F
G
Lowes.com/harborbreezeLowes.com/harborbreeze
Loading...