Hanwha Techwin XNV-8081RE operation manual
NETWORK CAMERA
User Manual
XNV-6081RE/XNV-8081RE
XND-6081REV/XND-8081REV
Network Camera
User Manual
Copyright
Hanwha Techwin
©2020
Trademark
Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their
respective company.
Restriction
Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without
formal authorization.
Disclaimer
Hanwha Techwin
provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility.
right to change the contents of this document without prior notice.
Design and specications are subject to change without prior notice.
The initial administrator ID is “admin” and the password should be set when logging in for the rst time.
Please change your password every three months to safely protect personal information and to prevent the damage of the information
theft.
Please, take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a password.
makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be
Co., Ltd. All r ights reser ved.
Hanwha Techwin
reserves the
overview
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth.
(Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents
as they may deform or cause damage to the product.)
7. Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11. Only use attachments/ accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lighting storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
15. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or “LPS” and rated
from PoE(53V), 0.48 A. (XNV-6081RE/XND-6081REV)
16. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or “LPS” and rated
from PoE(53V), 0.48 A. (XNV-8081RE/XND-8081REV)
17. This product is intended to be supplied by isolation power.
18. If you use excessive force when installing the product, the camera may be damaged and malfunction.
If you forcibly install the product using non-compliant tools, the product may be damaged.
19. Do not install the product in a place where chemical substances or oil mist exists or may be generated. As
edible oils such as soybean oil may damage or warp the product, do not install the product in the kitchen or
near the kitchen table.
This may cause damage to the product.
20. When installing the product, be careful not to allow the surface of the product to be stained with chemical
substance.
Some chemical solvents such as cleaner or adhesives may cause serious damage to the product’s surface.
21. If you install/disassemble the product in a manner that has not been recommended, the production functions/
performance may not be guaranteed.
Install the product by referring to “Installation & connection” in the user manual.
22. Installing or using the product in water can cause serious damage to the product.
23. Although a rapid change in temperature could cause frost inside the dome, there will be no problem with the
video.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE
VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT.
Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids,
such as vases, shall be placed on the apparatus.
To prevent injury, this apparatus must be securely attached to the Wall/ceiling in accordance
with the installation instructions.
CAUTION
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION
: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in
the literature accompanying the product.
●● OVERVIEW
English _3
overview
Class construction
An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a
protective earthing connection.
Battery
Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as
sunshine, fire or the like.
The battery cannot be replaced.
Disconnection Device
Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in
your location.
When used outside of the U.S., it may be used HAR code with fittings of an approved
agency is employed.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
ATTENTION
IL Y A RISQUE D’EXPLOSION SI LA BATTERIE EST REMPLACÉE PAR UNE BATTERIE DE
TYPE INCORRECT.
METTRE AU REBUT LES BATTERIES USAGÉES CONFORMÉMENT AUX INSTRUCTIONS.
CAUTION
These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock do not perform any servicing other than that contained in
the operating instructions unless you are qualified to do so.
Please use the input power with just one camera and other devices must not be connected.
The ITE is to be connected only to PoE networks without routing to the outside plant.
The wired LAN hub providing power over the Ethernet (PoE) in accordance with
IEEE 802.3at shall be a UL Listed device with the output evaluated as a Limited Power
Source as defined in UL60950-1.
Unit is intended for installation in a Network Environment 0 as defined in IEC TR 62102.
As such, associated Ethernet wiring shall be limited to inside the building.
Please read the following recommended safety precautions carefully.
yDo not place this apparatus on an uneven surface.
yDo not install on a surface where it is exposed to direct sunlight, near heating equipment or
heavy cold area.
yDo not place this apparatus near conductive material.
yDo not attempt to service this apparatus yourself.
yDo not place a glass of water on the product.
yDo not install near any magnetic sources.
yDo not block any ventilation openings.
yDo not place heavy items on the product.
yPlease wear protective gloves when installing/removing the camera.
The high temperature of the product surface may cause a burn.
User’s Manual is a guidance book for how to use the products.
The meaning of the symbols are shown below.
yReference : In case of providing information for helping of product’s usages
yNotice : If there’s any possibility to occur any damages for the goods and human caused by
not following the instruction
Please read this manual for the safety before using of goods and keep it in the safe place.
We do not guarantee the quality of third-party products (e.g. lenses, accessories) that you
separately purchase.
Use properly grounded STP (shielded twisted pair) cables to connect the products.
4_ overview
CONTENTS
OVERVIEW
3
OUTDOOR VANDAL DOME CAMERA
9
INDOOR DOME CAMERA
18
INSTALLATION & CONNECTION
26
3 Important Safety Instructions
6 Recommended PC Specifications
6 Recommended Micro SD/SDHC/SDXC
Memory Card Specifications
6 NAS recommended specs
8 Optional Accessories for Installation
9 What’s Included
9 At a Glance
10 Installation
18 What’s Included
18 At a Glance
19 Installation
26 Adjusting the monitoring direction for the
camera
27 Connecting with other Device
NETWORK CONNECTION AND
SETUP
31
WEB VIEWER
36
APPENDIX
38
31 Connecting the Camera Directly to Local
Area Networking
31 Connecting the Camera Directly to a DHCP
Based DSL/Cable Modem
32 Using Device Manager
32 Automatically searching camera
32 Configuring IP address
33 Manually registering camera
33 Automatically configuring IP
34 Port Range Forward (Port Mapping) Setup
35 Connecting to the Camera from a Shared
Local PC
35 Connecting to the Camera from a Remote
PC via the Internet
36 Connecting to the Camera
37 Password setting
37 Login
37 Camera Web Viewer Setup
38 Specification
46 Product Overview
47 Troubleshooting
48 Open Source Announcement
●● OVERVIEW
English _5
overview
RECOMMENDED PC SPECIFICATIONS
• CPU : Intel(R) Core(TM) i7 3.4 GHz or higher
• RAM : 8G or higher
• Supported OS : MS Windows 8.1, 10, Mac OS X 10.13
• Recommended browser: Google Chrome
• Supported browsers: MS Explorer11, MS Edge, Mozilla Firefox (Window 64bit only),
• VGA : PCIe 256MB GDDR3 video graphics card or higher
※
Some functions may be restricted even in supported browsers.
Apple Safari (Mac OSX only)
RECOMMENDED MICRO SD/SDHC/SDXC MEMORY CARD SPECIFICATIONS
• Recommended capacity : 16GB to 256GB (MLC type)
• Recommended Manufacturers : SanDisk, Transcend
• Product Type : High endurance
• The compatibility varies depending on the card manufacturers and types.
NAS RECOMMENDED SPECS
• Recommended capacity : 200GB or higher is recommended.
• For this camera, you are recommended to use a NAS with the following manufacturer’s specs.
Recommended products : QNAP NAS, Synology NAS
6_ overview
●● OVERVIEW
Outdoor Vandal Dome Camera
XNV-6081RE/XNV-8081RE
9 18
Indoor Dome Camera
XND-6081REV/XND-8081REV
English _7
overview
CAUTION: Be ware of the
Rated Voltage and Polarity
of the power connection.
OPTIONAL ACCESSORIES FOR INSTALLATION
You can purchase appropriate optional accessories available.
Model name Hanging Mount Skin Cover All
XND-6081REV/XND-8081REV SBP-167HMW SBC-160B (Black)
8_ overview
XNV-6081RE/XNV-8081RE SBP-187HMW SBC-180B (Black)
SBP-300LMW (Parapet Mount)
SBP-300CMW (Ceiling Mount)
SBP-300WMW (Wall Mount)
SBP-300WMW1 (Wall Mount)
SBP-300NBW (Instalation Box)
SBP-300NBW (Wall Mount Base)
SBP-300PMW (Pole Mount)
SBP-300KMW (Corner Mount)
outdoor vandal dome camera
CAUTION: Be ware of the
Rated Voltage and Polarity
of the power connection.
CAUTION: Be ware of the
Rated Voltage and Polarity
of the power connection.
CAUTION: Be ware of the
Rated Voltage and Polarity
of the power connection.
WHAT’S INCLUDED
As for each sales country, accessories are not the same.
<XNV-6081RE/XNV-8081RE>
AT A GLANCE
f
IR LED
Illumination Sensor
g
e
a
Pipe-cover
Network
h
connection
terminal
(POE+IN)
Mount-plate
i
Camera-case
b
Reset button
Camera-module
c
Dome-cover
d
Zoom/Focus
j
Control Button
●● OUTDOOR VANDAL DOME CAMERA
Option (not included)
SBC-180B
(Color : Black)
k
PoE OUT
l
cover
Network
connection terminal
(POE OUT)
m
Audio & alarm
n
cable connection
terminal
Separator strap
Micro SD card slot
p
Video out
o
q
Micro USB
terminal
English _9
outdoor vandal dome camera
INSTALLATION
This camera is waterproof and in compliance with the IP67 / IP6K9K spec, but the jack connected to the external cable is not.
`
J
You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Precautions before installation
Ensure you read out the following instructions before installing the camera:
• Select an installation site that can hold at least 5 times the camera’s weight.
• Stuck-in or peeled-off cables can cause damage to the product or a fire.
• For safety purposes, keep anyone else away from the installation site.
And put aside personal belongings from the site, just in case.
• If the product is installed with excessive force, it may cause damage to the camera due to malfunction.
Forcing assembly using non-compliant tools may damage the product.
Removal
1. Peel off the tape fixing the camera case.
2. Take off the cushion protecting the camera lens.
Inserting a Micro SD Memory Card
Slide the Micro SD card into the Micro SD slot on the camera module in the direction of the arrow.
10_ outdoor vandal dome camera
Before installing the camera, the Micro SD memory card should be inserted while the power source and the body are
`
J
separated.
Do not forcefully insert it in the reverse direction. It might damage your Micro SD memory card and your product.
`
When it rains or the humidity is high, insertion or ejection of a Micro SD card is not recommended.
`
When installing/removing the Micro SD memory card, make sure you put the product body on a flat ground before working on it
`
in order to prevent accidents due to loss or drop of any parts.
Removing a Micro SD Memory Card
Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory
card from the slot.
Before removing the Micro SD memory card, in <Storage>, set the device to <Off> and press the [Apply] button and turn
`
J
the camera off.
If you turn off the camera or remove the Micro SD memory card that contains data from the product, the data may be lost or
`
damaged.
Installation (mount plate)
[Directly installing on wall/ceiling]
1-1. Attach the installation template on the desired surface and drill holes for screws and cables.
●● OUTDOOR VANDAL DOME CAMERA
1-2. Fix the mount plate using appropriate screws.
1-3. Pull out necessary cables among LAN/audio & alarm cables through the hole in the mount plate.
English _11
outdoor vandal dome camera
[Installing using pipe]
2-1. Attach the installation template and drill holes for screws and cables.
2-2. Separate the pipe cover of the mount plate by pressing its sides.
2-3. Place the pipe on the mount plate.
2-4. Fix the mount plate using appropriate screws.
2-5. Pull out necessary cables among LAN/audio & alarm cables through the pipe.
Installation (camera case)
Use a cable bush compliant with the LAN cable to be connected.
`
J
Camera main: use a cable with the diameter of Ø5 to 6.5
-
IP66 1-hole bush: use a cable with the diameter of Ø5 to 8.5
-
2-hole bush: use a cable with the diameter of Ø4.5 to 5.5
-
[Installing LAN cable] (When using only one CAM)
1-1. Pull off the extruded parts of the bush to be used.
1-2. Route the LAN cable through the bush and connect the LAN connector.
12_ outdoor vandal dome camera
1-3. Mount the bush to the camera case.
[Installing the LAN cable] (IP66) (When using only one CAM)
2-1. Pull off the extruded part of the 1-hole bush provided.
2-2. Use the cap installer to pass through the RJ45 cable.
Cap Installer
2-3. Mount the bush to the camera case.
●● OUTDOOR VANDAL DOME CAMERA
[Installing audio & alarm cables] (When using only one CAM)
3. Mount the bush of the provided audio & alarm cables to the camera case.
English _13
outdoor vandal dome camera
[Installing LAN cables] (When using CAM 1 and CAM 2)
4-1. Pull off the extruded parts of the bush to be used.
4-2. Route the LAN cable for CAM 1 through the bush and connect the LAN connector. (PoE+ IN)
4-3. Route the LAN cable for CAM 2 through the bush and connect the LAN connector. (PoE OUT)
CAM 2 (PoE OUT) CAM 1 (PoE+ IN)
4-4. Mount the bush to the camera case.
[Installing the LAN cables] (IP66) (When using CAM 1 and CAM 2)
5-1. Pull off the extruded part of the 1-hole bush provided.
5-2. Use the cap installer to pass through the RJ45 cable. (CAM 1&2)
Cap Installer
CAM 1 (PoE+ IN)
2x
CAM 2 (PoE OUT)
5-3. Mount the bush to the camera case.
14_ outdoor vandal dome camera
[Installing audio & alarm cables] (When using CAM 1 and CAM 2)
6-1. Pull off the extruded part of the 2-hole bush provided.
6-2. Route the LAN cables through the two holes in the bush and connect the LAN connector.
2-hole bushes cannot use any cap installers.
`
M
CAM 2 (PoE OUT) CAM 1 (PoE+ IN)
6-3. Mount the 2-hole bush to the camera case.
6-4. Mount the bush of the provided audio & alarm cables to the camera case.
7. Join the mount plate with the camera case.
2x
TR20
x4
●● OUTDOOR VANDAL DOME CAMERA
English _15
outdoor vandal dome camera
Installing the camera module
To use CAM 1 & 2, the LAN cable for CAM 1 must be connected first.
`
J
1. To connect CAM 2, remove the PoE OUT cover first.
2. Connect the LAN/audio & alarm cables to the camera module terminal.
3. Attach the camera module to the case.
When installing it, don't let your fingers stuck in between the camera module and the case.
`
J
A magnet is embedded at the bottom of the module
`
Take caution not to allow any foreign objects between the attaching surfaces.
`
Assembling the dome cover
[Directly installing on wall/ceiling]
1. Assemble the dome cover.
Make sure to firmly tighten the fastening screws so that there is no water damage issue.
`
J
Be careful not to alter the monitoring direction of your camera.
`
J
4x
TR20
x4
4. Adjust the lens to the desired direction with reference to “Adjusting the monitoring direction for the
camera” section. (page 26)
16_ outdoor vandal dome camera
[Using Weather cap]
1. Remove the screws from the dome cover.
2x
Outdoor installation
When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be
purchased in stores) so that water does not leak from the gap of the cable connected to the outside.
1. Connect the I/O and LAN cables.
2. Wrap the black cable jacket (Area A) and the cable connection area with waterproof (butyl rubber) tape so
that more than half of the butyl rubber tape is overlapped.
●● OUTDOOR VANDAL DOME CAMERA
2. Assemble the dome cover.
3. Mount the weather cap to the dome cover and fasten the screws.
Make sure to firmly tighten the fastening screws so that there is no water damage issue.
`
J
2x
TR20
TR20
Camera
Camera
Camera
If the cable jacket is not waterproofed properly, then it can directly cause leakage. Make sure to protect the cable with a
`
J
dense layer of taping.
Waterproof butyl tape is made of butyl rubber that can be stretched to twice its normal length.
`
System
System
AA
System
English _17
indoor dome camera
CAUTION: Be ware of the
Rated Voltage and Polarity
of the power connection.
CAUTION: Be ware of the
Rated Voltage and Polarity
of the power connection.
CAUTION: Be ware of the
Rated Voltage and Polarity
of the power connection.
indoor dome camera
WHAT’S INCLUDED
As for each sales country, accessories are not the same.
<XND-6081REV/XND-8081REV>
AT A GLANCE
f
IR LED
Illumination Sensor
g
a
b
h
Pipe-cover
Mount-plate
Network
connection
terminal
(POE+IN)
c
Reset button
i
Camera-case
d
Camera-module
Dome-cover
e
Zoom/Focus
j
Control Button
Option (not included)
SBC-160B
(Color : Black)
18_ indoor dome camera
k
PoE OUT
l
cover
Network
connection terminal
(POE OUT)
m
Audio & alarm
n
cable connection
terminal
Separator strap
Micro SD card slot
p
Video out
o
r
q
Micro USB
terminal
Microphone
cable connection
terminal
Loading...