Hanwha Techwin DIGIMAXV3 User Manual

Use this camera in the following order

Instructions

Set up the camera

driver

Before connecting the USB cable to the PC and this camera, you have to set up the camera driver. Install the camera driver that is contained in the Application S/W CDROM. (p.110)

Take a picture (p.26)

Insert the supplied USB cable into the PC USB port and the camera USB connection terminal.(p.99)

Check the camera power. If the power is turned off, slide the camera switch to power it on.

Take a picture

Insert the USB

cable

Check the camera

power

Check

[Removable Disk]

Do not insert the cigar jack plug to the DC input connection point as this results in electric shock or severe damage to your camera.

Open Window’s EXPLORER and search for [Removable Disk].

READY

Contents

Getting to know your camera 5 About the symbols 6 Caution 6 Warning 7 Danger 8 Special features 9 This digital camera can be used for 10 Manufacturer's contents 12 Identification of features 13 Front & Top 13 Back & Bottom 13 Side 14 5-function button 14 Mode dial 15 Connecting to Power 17 Inserting the memory card 20 Instructions on how to use the

memory card

21 Selecting the date and time 23 Language 25

LCD monitor indicator 27 Starting recording mode 29 Using the camera button to adjust the camera

32 LCD button 32

SHUTTER button 32 WIDE / TELE button 33 UP/ Voice memo button 35 MACRO / SUPER MACRO button 36 FLASH button 37 SELF-TIMER / REMOTE button 40 MENU/ OK button 42 MF button 43 +/- button 44 Using the LCD monitor to adjust the camera

46 How to use the menu 48 Size 49 Quality 50 A/S/M 51 Metering 53 Shooting 54 White Balance 56 Effect 57 Sharpness 58 My SET mode menu 59 Mode 59 Change 60

Starting the play mode 62 LCD monitor indicator 64 Information button 65

READY

RECORDING

PLAY

Contents

Thumbnail & Wide / Tele & Trimming button

65 Thumbnail / Enlargement / Trimming button

66 UP / Voice memo button 67 DOWN / LEFT / RIGHT button 68 MENU / OK button 68 DELETE button 69 PLAY & PAUSE button 70 Setting up the play back function using the LCD monitor

71 Slide show 72 Protect 73 Resize 74 Delete all 75 DPOF : Standard 76 DPOF : Index 77 DPOF : Cancel 78 Setup menu 79 File 80 Power off 81 Language 82 Format 83 Date set 85 Time set 86 Date type 87 Imprint 88 Sound 89 LCD brightness 90

Video 91 Connecting to an external monitor 92 Quick view 93 MyCAM menu 94 Start up image 94 Start up sound 95 Shutter sound 95 List of camera function 96 Starting PC mode 99 Important notes 101 Warning indicator 102 Before contacting a service center 103 Specifications 106

Software Notes 108 About the software 108 Setting up the application software 110 Removing the USB Driver for Windows 98SE

116 Removable Disk 118 Removing the removable disk 119 Setting up the USB Driver for MAC 121 Using the USB Driver for MAC 121 Digimax Viewer 122 MGI PhotoSuite III SE 123 FAQ 138

SOFTWARE

READY

Thank you for buying a Samsung Digital Camera.

Prior to using this camera, please read the user manual thoroughly. Keep the manual in a safe place.

Getting to know your camera

About the symbols

This manual contains instructions on using this camera that will help you to use this camera safely and correctly. This will help prevent danger and injury to others.

DANGER

DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

WARNING indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.

CAUTION

CAUTION indicates a potentially hazardous situation, which, if not avoided, may result in a minor or moderate injury.

NOTICE

NOTICE indicates a factor, which, if not avoided, may result in camera malfunction or poor image quality.

INFORMATION

INFORMATION indicates a factor, which should assist further in the operation of the camera.

About the symbols

The camera mode icons will be marked on the right side of the title bar. The title is available only in the marked camera mode. Refer to below.

Caution

Leaking, overheating, or burst batteries could result in fire or injury.

Use batteries with the correct specification for the camera. Do not short circuit, heat or dispose of batteries in fire. Do not use old batteries with new ones, or mix brands of batteries.

Ensure the batteries are positioned correctly with regard to polarity (+ / -). When the camera is not in use for long periods, always unplug the camera from its power source. Do not fire the flash while it is in contact with hands or objects. Do not touch the flash after using it continuously. It may cause burns. Do not move the camera while it is switched on, if you are using the AC Power Adapter. After use, always switch off the camera before unplugging the adapter from the AC Power wall socket. Then make sure that any connector cords or cables to other devices are disconnected before moving the camera. Failure to do so may damage the cords or cables and cause a fire or electric shock.

Icon Mode dial Camera working mode Icon Mode dial Camera working mode

Easy mode Program mode Portrait mode Night mode Aperture priority mode Shutter priority mode Manual mode Movie clip mode User set mode Voice recording mode

Play mode

READY

Do not use the flash in close proximity to people or animals. Positioning the flash too close to your subject’s eyes, may cause eyesight damage.

When taking photographs, never point the lens of the camera directly into very strong light. This may result in permanent damage to the camera or your eyesight.

Do not leave this camera in places subject to extremely high temperatures, such as a sealed vehicle, direct sunlight or other places of extreme variances in temperature. Exposure to extreme temperatures may adversely affect the camera’s internal components and could cause a fire.

When in use, do not cover the camera or AC Power Adapter. This may cause heat to build up and distort the camera body or cause a fire. Always use the camera and its accessories in a well-ventilated area.

For safety reasons keep this product and accessories out of reach of children or animals to prevent accidents e.g.:

Swallowing batteries or small camera accessories. In case of accidents, please consult a doctor immediately. There is a risk of permanent eye damage if the flash is operated at a distance of less than one meter from a person’s eyes. There is a possibility of injury from the camera’s moving parts.

Batteries and camera may become hot during prolonged use and it may result in camera malfunction. Should this be the case, allow the camera to sit idle for a few minutes to allow it time to cool.

Warning

Danger

Do not attempt to modify this camera in any way. This may result in fire, injury, electric shock or severe damage to you or your camera. Internal inspection, maintenance and repairs should be carried out by your dealer or Samsung Camera Service Center.

Please do not use this product in close proximity to flammable or explosive gases, as this could increase the risk of explosion.

Should any form of liquid or a foreign object enter the camera, do not use it. Switch off the camera, and then disconnect the power source (batteries or AC Power Adapter). You must contact your dealer or Samsung Camera Service Center. Do not continue to use the camera as this may cause a fire or electric shock.

Do not insert or drop metallic or inflammable foreign objects into the camera through access points e.g. CARD slot and battery chamber. This may cause a fire or electric shock.

Do not operate this camera with wet hands. This could pose a risk of electric shock.

READY

Special features

This digital camera has the following features.

A fine resolution of 3.2 mega pixels A 3X optical and 4X digital zoom lens A superior Schneider lens 9 power source options (a world first!) A Super macro(6cm) function 3 different “My SET” modes

An FCC warning

This device has been tested in accordance with the limits of a class B digital device under item 15 of the FCC rules. These limits are designed to provide protection against harmful interference in commercial installation. This equipment generates, absorbs and can emit radio frequency energy. If it is not installed and used in accordance with the instructions, it may cause harmful interference to radio communication. There is however, no guarantee that interference will not occur in a some situations. Should any interference occur when this device is in operation, please try one or more of the following measures.

Change the location and direction of any aerial. Increase distance between camera and affected device. Use a different socket away from the affected device. Please contact a Samsung agent or a radio/TV engineer.

This device complies with part 15 of the FCC Rules.

This digital camera can be used for

Printing images using a dedicated printer, DPOFcompatible printer or DPOFequipped photo lab.(p.76)

Down loading image files from camera to computer.(p.100)

Editing images on a PC.(p.123)

Taking a picture. (refer to page 26)

Viewing images on a TV screen or external monitor (refer to page 92)

READY

This digital camera can be used for

Inserting images directly into any electronic document

Taking a self-portrait and using the image to personalize name cards

You can even create your own unique giftwrap paper by using your digital images

Creation of a digital photo album

Recording your voice (refer to page 35)

Recording a movie clip (refer to page 30)

Please check that you have the correct contents before using this product.

Manufacturer's contents

Battery pack

marked contents are optional.

Digital Camera Pouch USB cableAV cable

Camera strap Product warrantySoftware CD User manual

SD memory card

Digimax Premium Power Pack : SLB-1437 KIT

Battery charger Cigar jack for car

AC adapter

Rechargeable battery

Remote controlCR-V3 battery

READY

Identification of features

Front & Top

Back & Bottom

Shutter button (p.32)

Flash fading control sensor

Remote control sensor

Power switch Microphone

Self-timer lamp

Viewfinder

Lens

Viewfinder

Autofocus indicator

lamp(Green)

Flash indicator

lamp(Red)

Mode dial (p.15)

Mode dial Lamp

WIDE/THUMBNAIL button (p.33/65)

5-function button

TELE/Digital zoom button (p.33/66)

Speaker

LCD monitor

Tripod socket PLAY mode button

DC input connection point

USB/ AV connection terminal

+&-/PLAY & PAUSE

button (p.44/70)

MF / DELETE

button (p.43/69)

LCD/INFROMATION

button (p.32/65)

Flash

Strap eyelet

Identification of features

Side

5-function button

FLASH / LEFT button

(p.37/68)

MACRO / SUPER MACRO / DOWN button

(p.36/68)

SELF-TIMER/REMOTE/ RIGHT button (p.40/68)

Voice memo / UP button

(p.35/67)

Battery chamber

Memory card slot

Memory card cover/ Battery chamber cover

MENU/ OK button

(p.42/68)

READY

Mode dial

EASY

You can select the desired working mode by using the mode dial located on the back of the camera. This digital camera has 8 working modes. These are listed below.

Easy mode To make camera operation easier, a bare minimum of camera settings are required in this mode, such as image size. ( for printing, memo and email)

PROGRAM

Program mode In program mode, you can take a properly exposed photograph. Moreover you can select all camera settings except aperture and shutter speed.

PORTRAIT

Portrait mode This is used for just portrait or both portrait and landscape shots.

NIGHT SCENE

Night scene mode This mode is used at night or against a dark background.

Mode dial

A/S/M

Aperture priority / Shutter priority / Manual mode The Aperture and Shutter can be set manually in the A/ S/ M mode.

MOVIE CLIP

Movie clip mode A movie clip can be recorded as long as the available recording time allows. Image size and type are listed below.

- Image size : 320 X 240

- File type : *.AVI

MySET

User set mode You can set your preferences and save them in this mode. There are 3 kinds of user setting modes.

VOICE RECORDING

Voice recording mode You can do voice recording and other audio in this mode.

READY

Connecting to Power

There are two ways in which to provide the camera with power. You can use batteries (AA Alkaline, CR-V3, Ni-MH, Li-ion), or alternatively, you can use an AC(100 ~ 250V) Adapter (DC 5V 2.0A).

3. To close the battery chamber cover, push it until it clicks.

2. Insert the batteries taking note of the polarity (+ / -).

1. Open the battery chamber cover by pushing in the direction of the arrow.

Using the batteries

Battery condition indicator There are 3 indicators for battery condition that are displayed on the LCD monitor.

: The batteries are fully charged. : Prepare new batteries. : There is no battery capacity. Replace with new batteries.

Inserting the AA type battery

Inserting the CR-V3 type battery

Connecting to Power

NOTICE

Important information about battery usage

- It is easy to buy the alkaline batteries, but the duration for using batteries varies in accordance with the battery manufacturers or photography conditions.

- Please remove the batteries if the camera will not be used for long periods. Batteries can lose power over time and are prone to leaking if kept inside the camera.

- We recommend high capacity ALKALINE batteries as manganese batteries cannot deliver sufficient power.

- Low temperatures (below O˚C) can affect the performance of the batteries and you may experience reduced battery life.

- Batteries will usually recover at normal temperatures.

- Do not use old and new batteries at the same time.

During extended use of the camera, the camera body may become warm. This is perfectly normal.

If you are planning to use this camera for long periods of time, it is advisable to use an AC adapter.

INFORMATION

This camera will automatically switch off when not in use for a period of time. Refer to [POWER OFF] function (p.81). We recommend batteries for digital camera (Within a year from the date of manufacture). The batteries are listed below.

Non rechargeable batteries : AA type - Alkaline, Ni-Mn, Ni-Zn, Lithium

CR-V3 type - Lithium

Rechargeable batteries : AA type - Ni-MH, Ni-Cd (over 1000mA)

Exclusive type - SLB-1437 (Digimax V3 only)

SBP-1103 (CR-V3 type)

READY

Connecting to Power

If you have access to a mains supply, using an AC Adapter allows the camera to be used for long periods of time. Plug the adapter into the connection point (DC IN 5V) on the camera. Remove the batteries when using the AC adapter.

Using the Digimax Premium Power Pack ( Optional : SLB-1437 KIT )

The Digimax Premium Power Pack contains a rechargeable internal Li-ion battery, a battery charger, a cigar jack for car and an AC adapter for use with Digimax V3.

Using the Digimax battery pack ( Optional : SBP-3605, 5V)

The Digimax Battery Pack is a rechargeable external Li-ion battery for use with most digital cameras.

These optional battery packs provide long lasting power and their operating performances are much improved over Ni-MH and Alkaline batteries. This is due to the mass storage lithium ion cell. Contact your local dealer or the nearest authorized Samsung camera service center to buy the optional battery packs.

Using the AC power adapter

DANGER

Always turn off the power before taking the AC adapter out of the mains supply. As with all mains powered devices, safety is important. Ensure that neither the camera nor adapter comes into contact with water or metallic materials. Please ensure that you use an AC adapter with the correct specification for the camera. Failure to do so may affect your warranty.

Inserting the memory card

1. Turn the power off using the power switch. Open the memory card cover and press the memory card as shown in the image and release.

2. Remove the memory card and close the memory card cover.

3. To close, push the card cover against the arrow until you hear a click. If the card cover does not close, check that the memory card is inserted correctly. Do not force the memory card.

2. Insert the memory card all the way into the memory card slot. The Label stuck to the memory card and the front side of the camera should face in the same direction. The memory card pins and the LCD monitor should face in the same direction.

1. Turn off the camera power and pull the memory card cover in the direction of the arrow to open.

Removing the memory card

READY

Instructions on how to use the memory card

NOTICE

If you open the memory card cover when the camera power is turned on, the power will turn off automatically. Don’t remove the memory card when the Autofocus indicator lamp(Green) is blinking as this may cause damage to data in the memory card.

You can use both an SD memory card and Multi Media Card (MMC). We recommend using the SD memory card as the Multi-Media Card need more time to stored the image than the SD memory card.

When using a 32MB SD memory card, the specified shooting capacity will be as follows. (These figures are intended as an indication of expected performance). These figures are approximate as image capacities can be affected by variables such as memory performance and subject matter.

The SD memory card has a write protect switch that prevents image files from being deleted or formatted. By sliding the switch to the bottom of the SD memory card, the data will be protected. By sliding the switch to the top of the SD memory card, the data protection will be canceled. Check the switch position before taking an image.

Recorded image size TIFF Super fine Fine Normal 2048X1536 (Large) 3 16 33 67 2048X1360 (Photo) 3 19 38 76 1024X768 (Medium) 13 67 135 271 512X384 (Small) 54 271 542 1085

Print Memo E-mail

19 135 1085

Write

protect

switch

Label

Card pins

SD(Secure Digital) memory card

EASY mode

Instructions on how to use the memory card

Maintenance of the memory card

Turn off the camera power whenever the memory card is being inserted or removed. Repeated use of the memory card will eventually reduce the memory card s performance. Should this be the case, you will need to purchase a new memory card. Wear and tear on the memory card is not covered by the Samsung warranty. The memory card is an electronic precision device. Do not bend, drop or subject the memory card to any heavy impact. Do not store the memory card in an environment with strong electronic or magnetic fields, e.g. near loud speakers or TV receivers. Please do not use or store in an environment where there are extremes in temperature. Do not allow the memory card to become dirty or to come into contact with any liquid. Should this happen, clean the memory card with a soft cloth. Please keep the memory card in its case when not in use. During and after periods of extended use, you may notice that the memory card is warm. This is perfectly normal. Do not use the memory card that is used in another digital camera or memory card reader. Do not use the memory card formatted by another digital camera or memory card reader.

Preserving the memory card data

If the memory card is subjected to any of the following, the recorded data may become corrupted :

- When the memory card is used incorrectly.

- If the power is switched off or the memory card is removed while recording, deleting (formatting) or reading.

Samsung cannot be held responsible for lost data. It is advisable to copy important data onto other media as back-up e.g. floppy disks, hard disks, CD etc. If there is insufficient memory available : If you press the shutter button for the shot, [CARD FULL !] message is displayed and the camera will not operate. To optimize the amount of memory in the camera, replace the memory card or delete unnecessary images stored on the memory.

READY

Selecting the date and time

You can record the date and time with the image data in the memory card.

2. Select the [SETUP] tab by pressing the RIGHT button. Select the [FORMAT] menu by pressing the DOWN/button. Press the DOWN / button again and the next menu page will be displayed. Press the UP or DOWN button and select [DATE SET].

3. Shift the cursor to the [DATE SET] sub menu by pressing the RIGHT button.

1. Turn on the power and press the MENU button. The recording mode menu will be displayed in the RECORDING mode, and the play mode menu will be displayed in the PLAY mode. (There is no associated menu in VOICE RECORDING mode.)

INFORMATION

Date setting range : 2002/01/01 ~ 2050.12.31

(Leap years and months are corrected automatically)

The default is 2003/01/01. 12:00 p.m.

MOVE:

PLAY SETUP MyCAM

CHANGE:

‘03/01/01 12:00 PM YY/MM/DD OFF

DATE SET TIME SET D.TYPE IMPRINT

BACK:

PLAY SETUP MyCAM

SET:OK

DATE SET TIME SET D.TYPE IMPRINT

YEAR

03 /01/01

Selecting the date and time

6. To select the correct time, select [TIME SETUP] at step 2. Press the MENU button again and the menu will be cancelled.

5. Press the OK button to confirm the setting. To return to the main menu or cancel the setting, press the LEFT button.

4. Select the correct date by pressing the 5-function button. RIGHT button : selects YEAR/ MONTH/ DAY item. UP or DOWN button : changes the value of each item.

NOTICE

If the batteries are removed, the date and time settings will remain for approximately 1 hour. After approximately 1 hour, the date and time will be changed to the default date and time. If the batteries are removed for a period longer than 1 hour, it may be necessary to reset the date and time.

BACK:

PLAY SETUP MyCAM

SET:OK

DATE SET TIME SET D.TYPE IMPRINT

MOVE:

PLAY SETUP MyCAM

CHANGE:

DATE SET TIME SET D.TYPE IMPRINT

‘03/01/01 12:00 PM YY/MM/DD OFF

MONTH

03/ 01 /01

READY

Language

There is a choice of languages that can be displayed on the LCD monitor.

INFORMATION

The default language is ENGLISH. You can select 15 languages. Those are listed below. English, Korean, T. Chinese, S. Chinese, Japanese, Russian, Germany, Spanish, French, Italian, Danish, Dutch, Swedish, Finnish, Portuguese. Even if the camera is restarted, the language setting will be maintained. Even if the [SOUND] function is [ON], the sound will not activate in this menu.

1. Turn on the power and press the MENU button. The recording mode menu will be displayed in RECORDING mode, and the play mode menu will be displayed in the PLAY mode. (There is no associated menu in VOICE RECORDING mode.)

2. Select the [SETUP] tab by pressing the RIGHT button. Press the UP or DOWN button and select [LANGUAGE].

3. Shift the cursor to the [LANGUAGE] sub menu by pressing the RIGHT button and select the language that you want by pressing the UP or DOWN button.

4. Press the OK button to confirm the setting. To return to the main menu or cancel the setting, press the LEFT button. Press the MENU button again and the menu will be cancelled.

BACK:

PLAY SETUP MyCAM

SET:OK

FILE PWR OFF LANGUAGE FORMAT

ENGLISH

EXIT:MENU

PLAY SETUP MyCAM

PAGE:

FILE PWR OFF LANGUAGE FORMAT

SERIES OFF ENGLISH NO

Recording mode

RECORDING

LCD monitor indicator

The LCD monitor displays information about the shooting functions and selections.

Image & Full Status

No. Description Icons Page

Recording mode

p.15

Camera shake warning

p.31

Flash

p.37

Self-timer, Remote

p.40

5 Voice memo p.35

6 Macro/ Super macro p.36

LCD monitor indicator

No. Description Icons Page

7 Metering p.53

8 ISO p.55

9 Exposure compensation p.44

Aperture compensation F5.6 p.44

Shutter speed compensation 1/250 p.44

10 Manual focus p.43

11 Date / Time 2003/01/31 10:34 AM

12 White Balance p.56

13 Sharpness p.58

14 Image quality p.50

15 Image size p.49

Continuous shot, AEB p.54

Number of available shots remaining

161

Remaining time( Movie clip/ Voice recording)

00:01:40 (hour : minute : second)

17 Auto focus frame

18 Zoom / Digital Zoom p.33

19 Battery p.17

20 Aperture value F5.6 p.45

Shutter speed 1/250 p.45

RECORDING

Starting recording mode

1. Insert the batteries (p.17). Insert the batteries taking note of the polarity (+ / -).

2. Insert the memory card (p.20).

3. Close the memory card cover.

4. Slide the power switch to turn on the camera.

5. Select the PROGRAM mode by rotating the mode dial.

Point the camera towards the subject and compose the image by using either the viewfinder or LCD monitor.

7. Press the shutter button to capture an image.

[DELETE] message may be displayed after taking a picture. Refer to p.93 for more information about [DEL. ANSWER].

Recording a still image

PROGRAM mode

INFORMATION

Manner mode Pressing the power button over 2 seconds changes the buzzer and start-up sound setting to OFF, though you have set the settings to ON. If you wish to hear the buzzer sound and startup sound, set the [SOUND] and [S.SOUND] settings in the SETUP mode to ON. There are two LED lamps (one green, one red) positioned next to the viewfinder.

- If the camera is in focus when you press the shutter button halfway, the green LED will illuminate and you can take an image. If the camera can focus on the subject, the autofocus frame in the center of the LCD monitor will change from white to green.

- If the red lamp illuminates, the flash can fire.

- If the red lamp blinks, the flash is being charged.

- When an image is being stored onto the memory card, the green lamp blinks slowly. When the image data has been stored, the green LED light will go out. After the green LED light has gone out, you can resume taking images.

NOTICE

A Blinking autofocus indicator lamp means that the camera cannot focus on the subject. Should this be the case, the camera is unable to capture an image clearly.

Starting recording mode

Recording audio Steps from 1-4 are the same as those for recording a still image.

Select the VOICE RECORDING mode by rotating the mode dial.

6. Press the shutter button to record audio.

- Press the shutter button once and audio is recorded for as long as the available recording time allows. The recording time will be displayed on the LCD monitor.

- Audio will still be recorded if the shutter button is released.

- If you wish to stop recording, press the shutter button again.

VOICE RECORDING mode

MOVIE CLIP mode

VOICE RECORDING mode

Recording a Movie clip Steps from 1-4 are the same as those for recording a still image.

5. Select the MOVIE CLIP mode by rotating the mode dial.

6. Point the camera towards the subject and compose the image by using either the viewfinder or LCD monitor.

7. Press the shutter button to take a movie clip.

Press the shutter button once and movie clips are recorded for as long as the available recording time allows. Movie clips will still be recorded if the shutter button is released. If you wish to stop recording, press the shutter button again. Image size and type are listed below.

- Image size : 320 x 240

- File type : *.AVI

INFORMATION

The available recording time may vary depending on shooting conditions and camera settings.

RECORDING

Starting recording mode

NOTICE

Camera shake warning. When the Flash Off or Slow synchro mode is selected in a low lighting condition, the camera shake warning indicator ( ) may appear on the LCD monitor. In this case, use a tripod, support the camera on a solid surface or change the flash mode to flash shot mode. Backlight compensated shots When taking an outdoor shot, avoid facing the sun, as the image may be dark because of the strong backlight. In backlight conditions, please use the exposure compensation in the PROGRAM or A/S/M mode. (refer to page 51). Avoid obstructing the lens or the flash when you capture an image. As there can be some differences between what is seen through the Viewfinder and the resulting image when taken at a range closer than 1.5m, it is recommended that you use the LCD monitor to compose these shots. Using the LCD monitor extensively will drain the batteries. We recommend turning off the LCD monitor and using the optical viewfinder as often as possible in order to extend battery life. Under certain conditions the auto focus system may not perform as expected.

- When photographing a subject that has little contrast.

- If the subject is highly reflective or shiny.

- If the subject is moving at high speed.

- When there is strong reflected light, or when the background is very bright.

- When the subject matter has only horizontal lines or the subject is very narrow (such as a stick or flagpole).

- The subject is too dark.

INFORMATION

A distance of 40cm between you and the camera (microphone) is the best distance to record sound.

Using the camera button to adjust the camera

You can check the recording status in the LCD monitor.

The LCD monitor is not turned off in the VOICE RECORDING mode.

Image & full information

Pressing the

LCD button

Pressing the

LCD button

Pressing the

LCD button

Image & basic information LCD off

Pressing the LCD button in the RECORDING (EASY, PROGRAM, PORTRAIT, NIGHT SCENE, A/S/M, MOVIE CLIP, My SET) mode will change the display as shown below.

Used for taking an image or recording audio in the RECORDING (EASY, PROGRAM, PORTRAIT, NIGHT SCENE, A/S/M, MOVIE CLIP, USER SET, VOICE RECORDING) mode.

In EASY, PROGRAM, PORTRAIT, NIGHT SCENE, A/S/M, MySET mode

- Pressing the shutter button down halfway activates the autofocus and checks the condition of the flash.

- Pressing the shutter down fully takes the image and stores the relevant data regarding the shot.

In MOVIE CLIP, VOICE RECORDING mode

- Pressing the shutter down fully takes the movie clip or records the audio. Press the shutter button once and the movie clip or the audio is recorded for as long as the available recording time allows. Movie clips or audio will still be recorded if the shutter button is released. If you wish to stop recording, press the shutter button again.

SHUTTER button

LCD button

RECORDING

INFORMATION

To use the digital zoom the LCD monitor has to be turned on. Images taken using the digital zoom may take a little longer for the camera to process. Allow time for this to take place. The digital zoom cannot be used in continuous shots, AEB shots and movie clip shots. You may notice a decrease in image quality when using the digital zoom. When the maximum (3X) optical zoom is selected, pressing the zoom button T increases the digital zoom ratio by 0.1 steps. If the movie clip is being recorded, the zoom operation cannot be activated.

WIDE / TELE button

WIDE zoom

Pressing the TELE button

TELE zoom Digital zoom 2.0X

Used for digital or optical zooming in / out. This camera has a 3X optical zoom and a 4X digital zoom function. Using both will offer a total zoom ratio of 12X. When you press the zoom (W/T) button, the zoom bar will display in the upper centre of the LCD monitor.

Zoom TELE

Optical zoom TELE

- Pressing the zoom button T. This will zoom into the subject i.e. the subject will appear nearer.

Digital zoom TELE

- When the maximum (3X) optical zoom is selected, pressing the zoom button T activates the digital zoom software.

- Releasing zoom button T stops the digital zooming at the required setting.

- Once the maximum digital zoom (4X) is achieved, pressing the zoom button T will have no effect.

- You can check the digital zoom rate with the [X1.1 ~ X 4.0] numerical mark next to the zoom bar.

WIDE / TELE button

Zoom WIDE

Optical zoom WIDE

- Pressing the zoom button W. This will zoom out from the subject i.e. the subject will appear further away.

- Pressing the W button continuously will set the camera to its minimum zoom setting i.e. the subject appears at its furthest from the camera.

Digital zoom WIDE

- When the digital zoom is in operation, pressing the zoom button W will reduce the digital zooming in steps.

- Releasing zoom button W stops digital zooming.

- Pressing the W button will reduce the digital zoom and then it will proceed to reduce the optical zoom until the minimum setting is reached.

NOTICE

Take care not to touch the lens to avoid taking an unclear image and possibly causing camera malfunction. If the image is dim, turn the camera power off and on again to modify the lens position. Take care not to press the lens as this may cause a camera malfunction. When the camera is turned on, take care not to touch the camera s moving lens parts as this may cause the resulting image to be dim and unclear. Take care not to touch the lens during the zoom operation as this may cause damage.

TELE zoom

Pressing the WIDE button

Optical zoom 2X WIDE zoom

Digital zoom 4X

Pressing the

WIDE button

Pressing the

WIDE button

Digital zoom 2X Optical zoom 3X

RECORDING

INFORMATION

A distance of 40cm between you and the camera (microphone) is the best distance to record a voice memo. Voice memo function is inactivated after finishing a voice memo. If you a record a new voice memo to an image that had a voice memo, the existing voice memo is deleted and a new voice memo will be recorded.

Camera working mode Setting EASY PROGRAM PORTRAIT User can select the voice memo on / off NIGHT SCENE A/ S/ M, MySET MOVIE CLIP User can select the sound recording on / off VOICE RECORDING Not Available

Voice memo setting

UP/ Voice memo ( ) button

When the menu is displayed on the LCD monitor, pressing the UP button makes the menu cursor move up or change the sub menu value. When the menu is not displayed on the LCD monitor, the UP button operates as the voice memo button. You can add your voice to a stored still image.

Recording a voice memo

1. Rotate the mode dial to the RECORDING( except MOVIE CLIP, VOICE RECORDING) mode.

2. Press the VOICE MEMO button. If the voice memo indicator is displayed on the LCD monitor, the setting is completed.

3. Press the shutter button and take a picture. The picture is stored on the memory card.

4. Voice memo will be recorded for ten seconds from the moment the picture is stored. In the middle of the sound recording, pressing the shutter button will stop the voice memo.

MACRO ( ) / SUPER MACRO ( ) button

When the menu is displayed on the LCD monitor, pressing the DOWN button makes the menu cursor move down or changes the sub menu value. When the menu is not displayed on the LCD monitor, the button operates as the MACRO ( ) / SUPER MACRO ( ) button. The photography range is 0.06m ~ 0.8m. Selecting the MACRO/ SUPER MACRO

1. Rotate the mode dial to the RECORDING (except PORTRAIT, NIGHT SCENE, VOICE RECORDING) mode.

2. Press the MACRO button. The macro indicator will be displayed on the LCD monitor. Press the MACRO button until the desired MACRO mode indicator displays on the LCD monitor. In the MOVIE CLIP mode, only the macro mode can be used.

3. Take a picture with the desired macro mode.

Selecting the macro mode Selecting the super macro mode

NOTICE

The super macro can be activated only in the wide zoom mode. You cannot use the zoom(wide/tele) button in the super macro mode.

Icon Macro mode Definition

Used for macro shots (0.3 m ~ 0.8m).

Used for macro shots (0.06m ~ 0.3m).

MACRO

SUPER

MACRO

Macro mode type

RECORDING

Camera working mode Setting ( marked camera working mode is the default setting.) EASY PROGRAM PORTRAIT Normal (Fixed) NIGHT SCENE Normal (Fixed) A/ S/ M, USER SET Normal Macro Super macro MOVIE CLIP Normal Macro VOICE RECORDING Not Available

Macro mode setting

INFORMATION

When the macro or super macro mode is selected, It is possible that camera shake will occur. If this is the case, use a tripod to eliminate this. When super macro is selected, the flash mode is changed to Flash off automatically.

FLASH ( ) button

Selecting the Auto flash

Normal Macro Super macro

When the menu is displayed on the LCD monitor, pressing the LEFT button makes the cursor shift to the main menu. When the menu is not displayed on the LCD monitor, the LEFT button operates as the FLASH ( ) button.

Selecting the flash mode

1. Rotate the mode dial to the RECORDING ( except MOVIE CLIP, VOICE RECORDING) mode.

2. Press the FLASH ( ) button until the desired FLASH mode indicator displays on the LCD monitor. Use the correct flash to suit the environment.

MACRO ( ) / SUPER MACRO ( ) button

FLASH ( ) button

Indicator Flash mode Indicator

Definition

If the subject or background is dark, the camera flash will operate automatically.

Flash mode indicator

Red eye

reduction

Slow synchro

Fill in flash

Flash off

The flash does not fire. Select this mode when capturing images in a place or situation where flash photography is prohibited. When you take an image in a low light condition, the camera shake warning indicator ( ) will display on the LCD monitor.

If a subject or background is dark, the camera flash will work automatically and will reduce the red-eye effect by using the red-eye reduction function.

The flash fires regardless of available light. The intensity of the flash will be controlled, according to the prevailing conditions. The brighter the background or subject is, the less intense the flash will be.

The flash will operate in conjunction with a slow shutter speed in order to obtain the correct exposure. We recommend using a tripod. When you take an image in a low light condition, the camera shake warning indicator ( ) will display on the LCD monitor.

INFORMATION

Using the flash frequently will reduce the life of the batteries. Under normal operating conditions the charging time for the flash is normally within 7 seconds. If the batteries are weak, the charging time will be longer. In super macro mode, continuous shot or AEB mode, the flash function will not operate.

RECORDING

NOTICE

Take photographs within the flash range. The flash ranges are listed below.

The image quality is not guaranteed if the subject is too close or highly reflective. The LCD monitor is turned off for a while after using the flash to recharge it.

Flash mode setting

Camera working mode Setting ( marked camera working mode is the default setting.) EASY PROGRAM, MySET PORTRAIT Red eye reduction Fill in Off NIGHT SCENE Slow synchro Off A/ S/ M Off Fill in Slow synchro MOVIE CLIP Flash off (Fixed) VOICE RECORDING Not Available

ISO Auto 100 200 400

WIDE 0.8 ~ 3m 0.8 ~ 2.6m 1 ~ 3.7m 1 ~ 5.2m TELE 0.8 ~ 2m 0.8 ~ 1.5m 1 ~ 2.1m 1 ~ 2.9m WIDE 0.3 ~ 0.8m 0.3 ~ 0.8m 0.3 ~ 0.8m 0.3 ~ 0.8m TELE 0.3 ~ 0.8m 0.3 ~ 0.8m 0.3 ~ 0.8m 0.3 ~ 0.8m

Red eye reduction Off Auto Red eye reduction Fill in Slow synchro Off

Normal focus

MACRO

FLASH ( ) button

SELF-TIMER / REMOTE button

When the menu is displayed on the LCD monitor, pressing the RIGHT button makes the cursor shift to the sub menu. When the menu is not displayed on the LCD monitor, the RIGHT button operates as the SELFTIMER ( ) / REMOTE ( ) button. Selecting the self-timer

1. Rotate the mode dial to the RECORDING ( except VOICE RECORDING) mode.

2. Press the SELF-TIMER button until the desired mode indicator displays on the LCD monitor.

- Selecting the self-timer mode : Pressing the shutter button will allow an interval of ten seconds

before the image is taken. After that, the self-timer is cancelled.

- Selecting the remote mode : Pressing the shutter button in the remote controller will allow an

interval of 2 seconds before the image is taken. In the remote mode, you cannot use the shutter button.

Selecting the 2sec. self-timer mode Selecting the remote mode

Self-timer/ remote mode definition

Indicator Mode Definition

Pressing the shutter button will allow an interval of 2 seconds before the image is taken.

10s

Pressing the shutter button will allow an interval of 10 seconds before the image is taken.

Remote mode You can take a picture with the remote controller.

RECORDING

INFORMATION

Self-timer lamp In 10s self-timer : For the first seven seconds, the LED blinks at one second intervals.

For the final three seconds, the LED blinks quickly at 0.5 second intervals. In 2s self-timer : The LED blinks at 2second intervals. If you operate the Power switch, Mode dial, and Self-timer button during the self-timer operation, the self-timer function is cancelled. Use a tripod to prevent the camera from shaking.

Self-timer/ remote mode setting

Camera working mode Setting ( marked camera working mode is the default setting.) EASY Off 10s self-timer Remote PROGRAM PORTRAIT NIGHT SCENE A/ S/ M, MySET MOVIE CLIP Off Remote

VOICE RECORDING

Not Available

Off 2s self-timer 10s self-timer Remote

SELF-TIMER / REMOTE button

Remote control range When you take a picture by using the remote control, refer to the illustration as shown alongside about the remote control range.

Shutter button on the remote control

SELF-TIMER/ REMOTE button

INFORMATION

The menu will not be displayed on the LCD monitor in the following circumstances:

- When another button is being operated.

- While image data is being processed.( when the green LED next to the viewfinder blinks)

- When there is no battery capacity. When the menu is showing on the LCD monitor, it is not possible to operate the shutter button i.e. take an image. To take an image, simply cancel the menu display by pressing the MENU button.

MEMU button

- When you press the MENU button, a menu related to each camera mode will be displayed on the LCD monitor. Pressing it again will return the LCD to the initial display.

- A menu option can be displayed when the following are selected. EASY, PROGRAM, PORTRAIT, NIGHT SCENE, A/S/M, MOVIE CLIP and MySET. There is no menu available when the VOICE RECORDING mode is selected.

OK button

- When the menu is displayed on the LCD monitor, this button is used for shifting the cursor to the sub menu or for confirming data.

menu off

menu on

Pressing the

MENU button

EXIT:

PROG SETUP MyCAM

PAGE:

SIZE QUALITY

METERING SHOOTING

2048x1536 NORMAL MULTI SINGLE

Changing the remote controller battery Contact your dealer or Samsung camera service center to buy the battery. The battery type is CR2050S 3V.

MENU/ OK button

RECORDING

MF button

In dark conditions, the autofocus may not function. If this occours, press the MF button and you can select manual focus. After changing the focus manually, the image can be dim. Take care when using this function.

While pressing the MF button, the MF bar will be displayed on the LCD monitor.

While pressing the MF button, select desired focus value by pressing the UP/ DOWN button and take a picture.

- Pressing the UP button : Focus at long range.

- Pressing the DOWN button : Focus at close range.

Release the MF button and the MF bar will disappear. If you change the focus value, the MF indicator will be displayed at the bottom of the LCD monitor.

INFORMATION

If you didn’t change the focus value while pressing the MF button, the auto focus is activated. The manual focus function is disabled in the EASY and VOICE RECORDING mode. The MF bar is divided into 3 parts according to the photography range.

When the photography range is within 0.06m ~ 0.3m, the flash mode is changed to FLASH OFF automatically. When you press the MF button, the numerical indicators will display on the right side of the LCD monitor. The figures are distances from the camera lens. The numerical indicators are just for your reference. Focus the subject by using the LCD monitor when using the manual focus.

Part of the MF bar Photography range

1st part 0.8m ~ infinity

2nd part 0.3m ~ 0.8m

3rd part (only in wide zoom mode) 0.06m ~ 0.3m

Pressing the MF button

After changing the focus value

+/- button

This camera automatically adjusts the exposure according to the ambient lighting conditions. However, you can select the exposure value by using this button. You can select the shutter speed and aperture value in the A/S/M mode.

In the PROGRAM, PORTRAIT, MySET mode

- While pressing the +/- button, select the desired exposure value by pressing the LEFT/ RIGHT button.

Aperture priority mode( A )

- While pressing the +/- button, select the desired aperture value by pressing the UP/ DOWN button.

- While pressing the +/- button, select the desired exposure value by pressing the LEFT/ RIGHT button.

Shutter priority mode( S )

- While pressing the +/- button, select the desired shutter speed by pressing the UP/ DOWN button.

- While pressing the +/- button, select the desired exposure value by pressing the LEFT/ RIGHT button.

RECORDING mode

Aperture priority mode

Shutter priority mode

RECORDING

+/- button

INFORMATION

If you change the exposure value, the expose indicator ( ) will be displayed on the bottom of the LCD monitor. When the camera is turned on again, the exposure compensation setting returns to 0.0EV (discarding the exposure compensation). Exposure compensation setting range : -2.0 ~ +2.0 EV (0.5 EV steps) If you increase the exposure value, the image will be brighter. If you decrease the exposure value, the image will be darker. The aperture value (Av) or shutter speed (Tv) can be selected according to the P/A/S/M mode in the MySET mode. Decreasing or increasing the exposure value may lead to images being under or over exposed (too dark or too bright).

Manual mode( M )

- While pressing the +/- button, select the desired shutter speed by pressing the UP/ DOWN button.

- While pressing the +/- button, select the desired aperture value by pressing the LEFT/ RIGHT button. In the manual mode, the exposure value can’t be compensated. Refer to page 51 for information on selecting the aperture priority / shutter priority / manual mode.

Manual mode

Using the LCD monitor to adjust the camera

Main menu Sub menu

Secondary menu

Camera working mode

SIZE

PRINT( 2048 x 1360 /SUPER FINE)

EASY

MEMO( 1024 x 768 /FINE)

E-MAIL( 512 x 384 /NORMAL)

2048 x 1536

2048 x 1360

1024 x 768

512x 384

QUALITY TIFF

SUPER FINE

FINE

NORMAL

P/A/S/M P/A/S/M MySET 1/2/3

A/S/M APERTURE PRIORITY

SHUTTER PRIORITY

MANUAL

METERING MULTI

SPOT

SHOOT MODE SINGLE

CONTINUOUS

AEB

ISO AUTO

100

200

400

PROGRAM, PORTRAIT,

NIGHT SCENE, A/S/M,

MySET 1/2/3

PROGRAM, PORTRAIT,

NIGHT SCENE, A/S/M,

MySET 1/2/3

A/S/M, MySET 1/2/3

PROGRAM, PORTRAIT, A/S/M, MySET 1/2/3

PROGRAM, A/S/M([AUTO]

is not available), MySET

1/2/3

EASY, PROGRAM, PORTRAIT, MySET 1/2/3

# of prints

±0.5 EV

EASY, PROGRAM,

PORTRAIT, MySET 1/2/3

Using the LCD monitor to adjust the camera

- Recording functions can be changed by using the LCD monitor.

In the RECORDING (EASY, PROGRAM, PORTRAIT, NIGHT SCENE, A/S/M, MOVIE CLIP, MySET, VOICE RECORDING) mode, pressing the MENU button displays the menu on the LCD monitor.

- The following functions are available, depending on the mode you have selected.

RECORDING

Using the LCD monitor to adjust the camera

Main menu Sub menu

Secondary menu

Camera working mode

WHITE BALANCE AUTO

DAYLIGHT

CLOUDY

FLUORESCENT

TUNGSTEN

EFFECT NORMAL

BLACK & WHITE

sRGB

SUNSET

SHARPNESS SOFT

NORMAL

VIVID

PROGRAM, A/S/M, MOVIE

CLIP, MySET 1/2/3

PROGRAM, A/S/M,

MOVIE CLIP,

MySET

1/2/3

PROGRAM, A/S/M,

MOVIE CLIP,

MySET

1/2/3

INFORMATION

The menu will not be displayed on the LCD monitor in the following circumstances:

- When another button is being operated.

- While image data is being processed. ( when the green LED next to the viewfinder blinks)

- When there is no battery capacity. When the menu is showing on the LCD monitor, it is not possible to operate the shutter button i.e. capture an image. To capture an image, simply cancel the menu display by pressing the MENU button.

How to use the menu

Every camera working mode has [SETUP] and [MyCAM] tabs in their own menu. The main menus of the first tab are changed by different camera working modes.

1. Turn the camera power on and press the menu button. There are 3 tabs related to each camera mode in the menu. There is no menu available when the VOICE RECORDING mode is selected.

2. Shift the tab cursor by pressing the LEFT/ RIGHT button.

3. Select a menu by pressing the UP/ DOWN button.

4. Shift the cursor to the sub menu by pressing the RIGHT button. To shift the cursor to the main menu, press the LEFT button.

5. Select the desired sub menu by pressing the UP/ DOWN button. If there is another menu under the sub menu, press the RIGHT or OK button and the cursor shifts to another sub menu. To shift the cursor to the previous menu or cancel the menu setting, press the LEFT button.

6. Press the OK button to confirm the setting. Press the menu button twice and the menu display will disappear.

RECORDING mode

EXIT:

PROG SETUP MyCAM

PAGE:

SIZE QUALITY METERING SHOOTING

2048x1536 FINE MULTI SINGLE

SETUP mode MyCAM mode

Pressing the

LEFT / RIGHT button

Pressing the

LEFT / RIGHT button

MOVE:

PROG SETUP MyCAM

CHANGE:

SIZE QUALITY METERING SHOOTING

2048x1536 FINE MULTI SINGLE

Pressing the

UP/ DOWN button

Pressing the

LEFT/ RIGHT button

MOVE:

PROG SETUP MyCAM

CHANGE:

SIZE QUALITY METERING SHOOTING

2048x1536 FINE MULTI SINGLE

BACK:

PROG SETUP MyCAM

SET:OK

SIZE QUALITY METERING SHOOTING

TIFF S.FINE FINE NORMAL

EXIT:

PROG SETUP MyCAM

PAGE:

FILE PWR OFF LANGUAGE FORMAT

SERIES OFF ENGLISH NO

EXIT:

PROG SETUP MyCAM

PAGE:

S.IMAGE S.SOUND SH.SOUND

IMAGE1 SOUND1 SH.SOUND1

RECORDING

Size

You can select the image size you require.

1. Rotate the mode dial to the RECORDING mode and press the MENU button.

2. Press the DOWN button and the cursor will be shifted to the main menu.

3. Select [SIZE] menu by pressing the UP/DOWN button.

4. Press the RIGHT button and the cursor will shift to the [SIZE] sub menu.

5. Press the OK button to confirm the setting. Press the menu button twice and the menu display will be disappeared. Take a picture.

INFORMATION

A large image uses more memory, so increasing the image size will reduce the total number of shots you can store in the memory. Even though the camera is restarted, the image size setting is maintained.

EASY mode Select the desired sub menu by pressing the UP/DOWN button.

- PRINT : Taking a picture for printing (2048 X 1360 / Super fine)

- MEMO : Taking a picture for a web site image (1024 X 768 / Fine)

- E-MAIL : Taking a picture for e-mail (512 X 384/ Normal)

PROGRAM, PORTRAIT, NIGHT SCENE, A/S/M, MySET 1/ 2/ 3 mode Select the desired sub menu by pressing the UP/DOWN button.

- 2048x1536 (LARGE)

- 2048x1360 (PHOTO)

- 1024x768 (MEDIUM)

- 512x384 (SMALL)

BACK:

EASY SETUP MyCAM

SET:OK

SIZE

SHOOTING

MEMO

E-MAIL

BACK:

PROG SETUP MyCAM

SET:OK

SIZE

QUALITY

METERING

SHOOTING

2048x1536

2048x1360

1024x768

512x384

Quality

In RECORDING mode, you can select the image quality (Data compression rate).

INFORMATION

The higher the QUALITY setting, the better the final image will be. However, the high quality setting will require more memory and therefore reduce the number of images you can store on the memory. SUPER FINE is the highest quality and NORMAL is the lowest setting. Choose the setting appropriate for your needs. The image file is stored in *.jpg (Default). But, if you select TIFF in the quality menu, the image file is stored in *.tif. TIFF format is an uncompressed image file format for an expert. If you take a picture with the TIFF file format, the number of available shots is decreased and the time for recording the image file will be longer because the TIFF file size is bigger than the JPG file format. When the TIFF file is being recorded to the memory card, a [PLEASE WAIT!] message will be displayed on the LCD monitor. This file format complies with DCF(Design rule for Camera File system). Even if the camera should be restarted, the quality setting is maintained. But, if you select TIFF quality, the quality setting will be changed to FINE after restarting the camera. When using the 32MB SD memory card, the specified shooting capacity will be as follows. (These figures are intended as an indication of expected performance)

QUALITY IMAGE SIZE

LPMS TIFF (1:1) 3 3 13 54 Super fine (4:1) 16 19 67 271 Fine (8:1) 33 38 135 542 Normal (12:1) 67 76 271 1085

1. Rotate the mode dial to the RECORDING mode and press the MENU button.

2. Press the DOWN and the cursor will be shifted to the main menu.

3. Select [QUALITY] menu by pressing the UP/DOWN button.

4. Press the RIGHT button and the cursor will shift to the [QUALITY] sub menu.

Select the desired sub menu by pressing the UP/DOWN button.

- TIFF : TIFF - FINE :

- SUPER FINE : - NORMAL :

6. Press the OK button to confirm the setting. Press the menu button twice and the menu display will disappear. Take a picture.

BACK:

PROG SETUP MyCAM

SET:OK

SIZE

QUALITY

METERING

SHOOTING

TIFF

FINE

NORMAL

RECORDING

A / S / M

In this mode you can select the shutter speed or aperture value to your preference.

1. Rotate the mode dial to the A/ S/ M mode and press the MENU button.

2. Press the DOWN button and the cursor will be shifted to the main menu.

3. Select [A/S/M] menu by pressing the UP/DOWN button.

4. Press the RIGHT button and the cursor will shift to the [A/S/M] sub menu.

Select the desired sub menu by pressing the UP/DOWN button.

Aperture priority ( A ) : You can select the aperture value in this mode. The camera calculates the best shutter speed automatically to the proper exposure value. Shutter priority ( S ) : You can select the shutter speed in this mode. The camera calculates the best aperture value automatically to the proper exposure value. Manual ( M ) : You can select the shutter speed and the aperture value in this mode.

6. Press the OK button to confirm the setting. Press the menu button twice and the menu display will disappear. Take a picture.

INFORMATION

After pressing the shutter button half way down, the values that were changed in the A/S/M mode will be applied to the picture. If the aperture value or shutter speed is out of the limit of application, the value that is displayed on the LCD monitor will show as red. However, you will still be able to take a picture.

BACK:

A/S/M SETUP MyCAM

SET:OK

SIZE

QUALITY

A/S/M

METERING

EXIT:MENU

A/S/M SETUP MyCAM

PAGE:

SIZE

QUALITY

A/S/M

METERING

2048x1536

FINE

MULTI

It warns that : To be the properly exposed, the aperture value

should be smaller than F 2.8. The minimum aperture

value that you can select is F 2.8.

A / S / M

Aperture priority mode ( A )

- The small aperture value is used for portraits to separate the subject from the background. The large aperture value is used for landscape photographs to keep the foreground and background in focus.

- While pressing the +/- button, select the desired aperture value by pressing the UP/ DOWN button.

- To change the exposure value, press the LEFT/ RIGHT button by pressing the +/- button.

- Point the camera towards the subject and compose the image and take a picture.

Shutter priority mode ( S )

Fast shutter speeds are used in sport photography to capture action shots. Slow shutter speeds can be used to show the flow of motion such as water cascading over a waterfall.

- While pressing the +/- button, select the desired shutter speed by pressing the UP/ DOWN button.

- To change the exposure value, press the LEFT/ RIGHT button by pressing the +/- button.

- Point the camera towards the subject and compose the image and take a picture.

Manual mode ( M )

- You can select the shutter speed and the aperture value in this mode.

- While pressing the +/- button, select the desired shutter speed by pressing the UP/ DOWN button.

- While pressing the +/- button, select the desired aperture value by pressing the LEFT/ RIGHT button.

- Point the camera towards the subject and compose the image and take a picture.

RECORDING

Metering

When the camera cannot calculate a desired exposure, you can change the metering method.

INFORMATION

The default metering mode is Multi pattern metering. If the subject is not the centre of the focus, do not use the spot metering as there may be an exposure error. In this case, use exposure compensation. Even if the camera is restarted, the metering setting is maintained.

BACK:

PROG SETUP MyCAM

SET:OK

SIZE

QUALITY

METERING

SHOOTING

MULTI

SPOT

EXIT:

PROG SETUP MyCAM

PAGE:

SIZE

QUALITY

METERING

SHOOTING

2048x1536

FINE

MULTI

SINGLE

1. Rotate the mode dial to the RECORDING mode and press the MENU button.

2. Press the DOWN button and the cursor will be shifted to the main menu.

Select the [METERING] menu by pressing the UP/DOWN button.

4. Press the RIGHT button and the cursor will shift to the [METERING] sub menu.

5. Select the desired sub menu by pressing the UP/DOWN button.

- Multi pattern metering : Exposure will be calculated based on an average of the available light in the image area. However, the calculation will be biased towards the centre of the image area.

- Spot metering : Use this function when there is backlight or when photographing a subject that has little contrast. In backlighting conditions adjust the light metering to suit the subject matter.

6. Press the OK button to confirm the setting. Press the menu button twice and the menu display will disappear. Take a picture.

Shooting

You can select the continuous shooting or AEB shooting in this menu.

AEB is not available in the A/S/M mode.

1. Rotate the mode dial to the RECORDING mode and press the MENU button.

2. Press the DOWN button and the cursor will be shifted to the main menu.

3. Select the [SHOOTING] menu by pressing the UP/DOWN button.

4. Press the RIGHT button and the cursor will shift to the [SHOOTING] sub menu.

5. Select the desired sub menu by pressing the UP/DOWN button.

- SINGLE : you can take only one picture at a time.

- CONTINUOUS : In this mode, you can capture moving subjects continuously.

- AEB (Auto Exposure Bracket) :

In this mode, you can take a 3-image bracket of a scene. There is an over exposed image, normally exposed image and

under exposed image in a bracket. When you select continuous shot or AEB, you can select the exposure bracket and the number of continuous shots in [SHOOTING] sub menu.

6. Press the OK button to confirm the setting. Press the menu button twice and the menu display will disappear. Take a picture.

INFORMATION

The flash mode is set to “flash off” in continuous shooting and AEB shooting. After completing the continuous or AEB shot, the shooting mode is changed to [SINGLE] automatically. Once a continuous sequence has begun, it will continue until the selected number of shots has been taken. Releasing the shutter button will not interrupt this function. The maximum number of shots in a sequence is governed by the image settings. Using a 32MB SD memory card, the specified shooting capacity will be as follows. (These figures are intended as an indication of expected performance)

If you change the image size or quality after selecting the continuous shot or AEB shot, the shooting mode will be turned to single shot mode automatically.

Quality Size Large Photo Medium Small TIFF (1:1) N/A N/A N/A N/A Super fine (4:1) 4 4 16 66 Fine (8:1) 8 9 32 99 Normal (12:1) 16 18 66 99

BACK:

PROG SETUP MyCAM

SET:OK

SIZE

QUALITY

METERING

SHOOTING

SINGLE

CONTINUOUS

AEB

RECORDING

Shooting

INFORMATION

Continuous and AEB shots cannot be selected in the TIFF image quality format. To take the continuous shot, the number of available shots must be more than 2 because the minimum number of the continuous shots are 2. To take the AEB shots, the number of available shots must be more than 3 because of the same reason. Camera shake can be a problem when using the AEB shooting mode and it takes time to store the AEB image to the memory. We recommend using a tripod.

You can select the camera’s sensitivity to light by selecting the ISO sub menu. The speed or specific light-sensitivity of a camera is rated by ISO numbers.

1. Rotate the mode dial to the RECORDING mode and press the MENU button.

2. Press the DOWN button and the cursor will be shifted to the main menu.

3. Select the [SHOOTING] menu by pressing the UP/DOWN button.

4. Press the DOWN button on the [SHOOTING] menu and the next menu page will be displayed.

5. Select the [ISO] menu by pressing the UP/DOWN button.

8. Press the OK button to confirm the setting. Press the menu button twice and the menu display will disappear. Take a picture.

Press the RIGHT button and the cursor will shift to the [ISO] sub menu.

7 Select the desired sub menu by pressing the UP/DOWN button.

- AUTO : The camera's sensitivity is automatically changed by variables such as lighting value or subject brightness.

- 100/ 200/ 400 : In the same lighting conditions, the higher the ISO value is, the faster the shutter speed will be. However, the images can be saturated in very bright conditions.

INFORMATION

The higher the number, the more sensitive it is to light. As with film, the higher speeds usually induce more electronic noise so the image gets grainier. Even if the camera is restarted, the the ISO setting will be maintained. [AUTO] is not applied to A/S/M mode.

ISO

BACK:

PROG SETUP MyCAM

SET:OK

ISO

W.B

EFFECT

SHARP

AUTO

100

200

400

White Balance

The white balance control allows you to adjust the colors to appear more natural looking.

1. Rotate the mode dial to the RECORDING mode and press the MENU button.

2. Press the DOWN button and the cursor will be shifted to the main menu.

3. Select the [SHOOTING] menu by pressing the UP/DOWN button.

4. Press the DOWN button on the [SHOOTING] menu and the next menu page will be displayed.

5. Select the [W.B] menu by pressing the UP/DOWN button.

Press the RIGHT button and the cursor will shift to the [W.B] sub menu.

Select the desired sub menu by pressing the UP/DOWN button.

- AUTO : The camera automatically selects the appropriate white balance settings, depending on the prevailing lighting conditions.

- DAYLIGHT : For taking images outside.

- CLOUDY : For taking images under a cloudy and

overcast sky.

- FLUOR. : For shooting under fluorescent lighting.

- TUNGSTEN : For shooting under tungsten (standard light bulb) lighting.

8. Press the OK button to confirm the setting.

Press the menu button twice and the menu display will disappear. Take a picture.

INFORMATION

Different lighting conditions may cause a color cast on your images. Even if the camera is restarted, the white balance setting will be maintained.

BACK:

PROG SETUP MyCAM

SET:OK

ISO

W.B

EFFECT

SHARP

AUTO

DAYLIGHT

CLOUDY

FLUOR.

EXIT:

PROG SETUP MyCAM

PAGE:

SIZE

QUALITY

METERING

SHOOTING

2048x1536

FINE

MULTI

SINGLE

RECORDING

Effect

Using the camera’s digital processor, it is possible to add special effects to your images.

1. Rotate the mode dial to the RECORDING mode and press the MENU button.

2. Press the DOWN button and the cursor will be shifted to the main menu

3. Select the [SHOOTING] menu by pressing the UP/DOWN button.

4. Press the DOWN button on the [SHOOTING] menu and the next menu page will be displayed.

5. Select the [EFFECT] menu by pressing the UP/DOWN button.

6. Press the RIGHT button and the cursor will shift to the [EFFECT] sub menu.

7. Select the desired sub menu by pressing the UP/DOWN button.

- NORMAL : No effect is added to the image.

- B & W : Converts the image to black and white.

- sRGB : sRGB is a device independent standard color model. Devices supporting sRGB can display the exact image color.

- SUNSET : Used for capturing images at sunset

8. Press the OK button to confirm the setting. Press the menu button twice and the menu display will disappear. Take a picture.

INFORMATION

Even if the camera is restarted, the effect setting will be maintained.

BACK:

PROG SETUP MyCAM

SET:OK

ISO

W.B

EFFECT

SHARP

NORMAL

B & W

sRGB

SUNSET

EXIT:

PROG SETUP MyCAM

PAGE:

SIZE

QUALITY

METERING

SHOOTING

2048x1536

FINE

MULTI

SINGLE

Sharpness

You can select the sharpness of still image.

1. Rotate the mode dial to the RECORDING mode and press the MENU button.

Press the DOWN button and the cursor will be shifted to the main menu.

3. Select the [SHOOTING] menu by pressing the UP/DOWN button.

4. Press the DOWN button on the [SHOOTING] menu and the next menu page will be displayed.

Select the [SHARP] menu by pressing the UP/DOWN button.

Press the RIGHT button and the cursor will shift to the [SHARP] sub menu.

7. Select the desired sub menu by pressing the UP/DOWN button.

- SOFT : This gives smooth edges and the final image will have a soft appearance.

- NORMAL : This setting will give a standard finish to the final image.

- VIVID : This will give the image a crisp and clear appearance.

8. Press the OK button to confirm the setting. Press the menu button twice and the menu display will disappear. Take a picture.

INFORMATION

Even though the camera is restarted, the sharpness setting is maintained.

BACK:

PROG SETUP MyCAM

SET:OK

ISO

W.B

EFFECT

SHARP

EXIT:

PROG SETUP MyCAM

PAGE:

SIZE

QUALITY

METERING

SHOOTING

2048x1536

FINE

MULTI

SINGLE

SOFT

NORMAL

VIVID

RECORDING

My SET mode menu

You can select your favorite settings that have been saved in this menu.

1. Rotate the mode dial to the MySET mode and press the

MENU button.

2. Press the DOWN button and the cursor will be shifted to the

main menu.

3. Select the [MODE] menu by pressing the UP/DOWN button.

4. Press the RIGHT button and the cursor will shift to the

[MODE] sub menu.

5. Select the desired sub menu by pressing the UP/DOWN

button.

6. Press the OK button to confirm the setting.

Press the menu button twice and the menu display will disappear. Take a picture To apply this function to the camera, change the MySET mode menu or press the DOWN button and select the CHANGE menu. Refer to the CHANGE menu.

You can select your favorite settings and save them in this menu

Main menu Sub menu

MODE MYSET1

MYSET2 MYSET3

CHANGE NO

YES

Mode

EXIT:MENU

MySET SETUP MyCAM

PAGE:

MODE

CHANGE

MYSET1

BACK:

MySET SETUP MyCAM

SET:OK

MODE

CHANGE

MYSET1

MYSET2

MYSET3

Change

The loaded My SET setting will be applied to the camera from this menu.

Rotate the mode dial to the MySET mode and press the MENU button.

2. Press the DOWN button and the cursor will be shifted to the main menu.

3. Select the [CHANGE] menu by pressing the UP/DOWN button.

4. Press the RIGHT button and the cursor will shift to the [CHANGE] sub menu.

5. Select the desired sub menu by pressing the UP/DOWN button.

- Selecting [NO] : The My SET menu will not be changed.

- Selecting [YES] : You can change your favorite menus. Refer to page 49 ~ 58 for information about the menus.

6. Press the OK button to confirm the setting. Press the menu button twice and the menu display will disappear. Take a picture

INFORMATION

P/A/S/M in the main menu stands for Program mode(P), Aperture priority(A), Shutter priority(S) and Manual mode(M). You can save one of the camera modes in the My SET mode.

EXIT:MENU

MySET SETUP MyCAM

PAGE:

MODE

CHANGE

MYSET1

BACK:

MySET SETUP MyCAM

SET:OK

MODE

CHANGE

YES

PLAY

Play mode

Starting the play mode

Turn the camera on and select the Play mode by pressing the play mode button ( ). The camera can now play back the images stored in a memory. You can set up the PLAY mode function by using the camera buttons and LCD monitor.

1. Select the PLAY mode by pressing the play mode button.

2. The last image stored on the memory is displayed on the LCD monitor.

3. Select an image that you want to play back by pressing the LEFT / RIGHT button.

Playing back a still image

INFORMATION

Even if the camera’s power is off, you can start the play mode by pressing the play mode button. The LCD monitor will remain in operation until the camera is switched off in PLAY mode. To turn off the camera power, slide the power switch. The menu will not display on the LCD monitor under the following circumstances:

- When another button is being pressed.

- While image data is being processed

- When there is no battery capacity.

PLAY

Starting the play mode

Playing back a movie clip Steps from 1-2 are the same as those to play back a still image.

Select the recorded movie clip that you want to play back by using the LEFT/RIGHT button. If you select a movie clip, the movie clip indicator ( ) will be displayed on the LCD monitor.

Press the play & pause button ( ) to play back a movie clip file.

- To pause while playing back a movie clip file, press the play & pause button again.

Press the play & pause button and the movie clip file will restart.

- To stop play back, press the LEFT/RIGHT button.

Playing back a recorded voice Steps from 1-2 are the same as those to play back a still image.

3. Select the recorded voice that you want to play back by using the LEFT/RIGHT button. If you select a recorded voice file, the voice indicator ( ) will be displayed on the LCD monitor.

4. Press the play & pause button ( ) to play back a recorded voice.

- To pause playing back a recorded voice, press the play & pause button again.

- Press the play & pause button and the recorded voice will restart.

- To stop play back, press the LEFT/RIGHT button.

LCD monitor indicator

The LCD monitor displays information about the shooting conditions.

No. Description Icons Page

1 Play mode

2 Movie clip

3 Voice memo p.67

4Protect indicator p.73

5 DPOF indicator p.76~78

6 Recording date 2003:01:31

7 Stored image number 6

8 Battery

9 Voice recording p.30

SIZE 2048X1536 : image size AV F2.8 : aperture value TV 1/60 : shutter speed ISO 100 : ISO sensitivity FLASH OFF : Whether using the flash or not DATE 2003:01:31 : recording date

PLAY

You can view up to 9 images at a time and trim an image. The last image stored on the memory is displayed on the LCD monitor. Press the 5 function button and you can play back another image.

Thumbnail button ( )

- Press the thumbnail button.

- The thumbnail display will highlight the image that had been showing at the time the thumbnail mode was selected.

- Press the 5 function button to move to a desired image.

- To view an image separately, press the enlargement button ( ).

Information button

The shooting information will be displayed on the LCD monitor. The last image stored in the memory is displayed on the LCD monitor. Pressing the LCD button in the PLAY mode will change the display as shown below.

Image & Icons

Pressing the

information

button

Pressing the

information

button

Pressing the

information

button

Image & information Image only

Thumbnail & Wide / Tele & Trimming button

Normal display mode Thumbnail display mode

Pressing the thumbnail

( ) button

Highlighted image

press the enlargement

( ) button

Thumbnail / Enlargement / Trimming button

Image enlargement

- Select an image that you want to enlarge and press the enlargement button.

- Different parts of the image can be viewed by pressing the 5 function button.

- Pressing the thumbnail button will zoom back to the original full sized image.

The location indicator is in the bottom left side of the LCD monitor.

Trimming : You can extract part of the image that you want and

save it separately.

- Select a section that you want to trim by pressing the 5 function button. Press the OK button and a message will be displayed as shown alongside.

- Select [YES] or [NO] by pressing the LEFT/ RIGHT button and press the OK button.

Selecting [YES] : a trimmed image that has the latest file name

will be displayed on the LCD monitor.

Selecting [NO] : an initial image will be displayed.

INFORMATION

The maximum enlargement rate in proportion to the image size.

If an image is enlarged, the enlargement indicator will be displayed in the bottom left of the LCD monitor. Movie clip, TIFF and WAV files can’t be enlarged. You may notice a decrease in image quality when you enlarge them. The image size of the trimmed image cannot be defined as it extracts only the part of the image displayed on the LCD monitor. If there is little memory space to save the trimmed image, the image can’t be trimmed.

Image size Large (Photo) Middle Small

Maximum enlargement rate X8.3 X4.3 X2.1

PLAY

UP / Voice memo button

1. Press the play mode button.

2. Press the 5 function button to select an image that you wish to add sound to.

3. Press the voice memo button ( ) and the voice memo indicator will display. The camera is now ready to record audio.

4. Press the shutter button to start recording. The [RECORDING] message will be displayed on the LCD monitor (as shown) and audio is recorded to the still image for 10 seconds.

5. Recording can be stopped by pressing the shutter button again.

6. [

] icon will be displayed on the LCD monitor after finishing

the voice memo.

INFORMATION

Audio can’t be recorded onto a movie clip file. When you press the shutter button to stop the audio recording, press the shutter button halfway and the buzzer sound will not be recorded. A distance of 40cm between you and the camera (microphone) is the best distance to record sound.

DOWN / LEFT / RIGHT button

DOWN / LEFT / RIGHT buttons activate the following.

DOWN button When the menu is displayed on the LCD monitor, pressing the DOWN button makes the menu cursor move down or change the sub menu value. LEFT button When the menu is displayed on the LCD monitor, pressing the LEFT button makes the cursor shift to the main menu. RIGHT button When the menu is displayed on the LCD monitor, pressing the RIGHT button makes the cursor shift to the sub menu.

INFORMATION

The menu will not be displayed on the LCD monitor in the following circumstances:

- When another button is being operated.

- While image data is being processed. (when the green LED next to the viewfinder blinks)

- When there is no battery capacity.

MENU / OK button

MENU button When you press the MENU button, the play mode menu will be displayed on the LCD monitor. Pressing it again will return the LCD to the initial display. OK button When the menu is displayed on the LCD monitor, the OK button is used for confirming data that is changed by using the 5 function button.

PLAY

DELETE ( ) button

This deletes an image stored on the memory card.

1. Press the play mode button.

2. Press the LEFT/ RIGHT button to select the image that you want to delete, and press the delete ( ) button.

A message as shown alongside will be displayed on the LCD monitor.

NOTICE

Before deleting an image from the camera, you should download (p.100) the image to your computer or protect (p.73) the image, if you want to keep it.

4. To cancel the deletion, press the LEFT button. Press the OK button and a message as shown alongside will be displayed on the LCD monitor. Select [DELETE] or [CANCEL] by pressing the UP/DOWN button and press the OK button.

Selecting [DELETE] : Once an image has been deleted, the

previous image in the sequence will appear on the LCD monitor.

Selecting [CANCEL] : The image will be displayed on the LCD monitor.

PLAY & PAUSE ( ) button

When the menu is not displayed on the LCD monitor, press the PLAY & PAUSE button to play and pause the movie clip, or a still image that has a voice memo or audio recording file.

1. Press the play mode button.

2. Press the LEFT/ RIGHT button to select an image that has voice memo, movie clip or audio recording file.

INFORMATION

The selected image plays back as a single image display. When the image is playing, the play & pause button, power switch and mode dial can be activated. When the image is paused, the left/ right button, power switch and mode dial can be activated.

3. Pressing the PLAY & PAUSE button activates the following.

- If an image is showing, but there is no sound (or movement) : Plays the sound clip or starts the movie clip.

- If the image is playing : The progress is paused.

If the PLAY & PAUSE button is pressed when the image is paused, the sound or movement will resume.

To select another image, pause the progress and press the LEFT/RIGHT button.

Initial play mode Playing Pause

PLAY

Setting up the play back function using the LCD monitor

Main menu Sub menu Secondary menu

SLIDE SHOW

(Default : OFF)

REPEAT ON

OFF

PROTECT ONE PICTURE UNLOCK

LOCK

ALL PICTURES UNLOCK

LOCK

RESIZE 1024 x 768

640 x 480

320 x 240

LOGO

DELETE ALL NO

YES

STANDARD ONE PICTURE

ALL PICTURES

INDEX PRINT NO

YES

CANCEL STANDARD

INDEX

OFF, 01 ~ 10 SEC.

00 ~ 30 PRINTS

PLAY mode functions can be changed by using the LCD monitor. In the PLAY mode, pressing the MENU button displays the menu on the LCD monitor.

Slide show

Images can be displayed continuously at pre-set intervals. You can view the slide show by connecting the camera to an external monitor.

INFORMATION

The default is OFF and the loading time depends on the image size and quality. The slide show will start from an image that was displayed on the LCD monitor. The [POWER OFF] function can’t be activated. While the slide show is playing, only the first frame of an AVI file is displayed. If there is only an image in the memory card, the slide show will not start.

1. Press the play mode button and press the menu button.

Press the DOWN button and the cursor will be shifted to the main menu.

Select the [SLIDE SHOW] menu by pressing the UP/DOWN button.

4. Press the RIGHT button and the cursor will shift to the [SLIDE SHOW] sub menu.

5. Select the desired sub menu by pressing the UP/DOWN button.

- If you select [01 ~ 10SEC], you can select the [REPEAT] secondary menu. Select [01 ~ 10SEC] and press the RIGHT button and the cursor will shift to the secondary menu.

6. Select the desired menu by pressing the UP/DOWN button.

- [OFF] : If a cycle is completed, the slide show will stop

automatically.

- [ON] : Even once a cycle(from the first image to the last

image) is completed, the slide show will continue to repeat itself.

Press the OK button to confirm the setting.Press the menu button twice and the slide show will start.

8. To pause the slide show, press the play & pause button. To start the slide show again, press the play & pause button again. Press the menu button twice again and the slide show will stop.

BACK:

PLAY SETUP MyCAM

SET:OK

SLIDE

PROTECT

RESIZE

DEL. ALL

01 SEC

BACK:

PLAY SETUP MyCAM

SET:OK

SLIDE

PROTECT

RESIZE

DEL. ALL

REPEAT

OFF

PLAY

Protect

This is used to protect specific shots from being accidentally erased (LOCK). It also releases images that have been previously protected (UNLOCK).

1. Press the play mode button and press the menu button.

Press the DOWN button and the cursor will be shifted to the main menu.

3. Select the [PROTECT] menu by pressing the UP/DOWN button.

4. Press the RIGHT button and the cursor will shift to the [PROTECT] sub menu.

5. Select the desired sub menu by pressing the UP/DOWN button.

- [ONE PIC.] : Only an image that is displayed on the LCD monitor is protected or unprotected.

- [ALL PICS.] : All of the stored images are protected or unprotected.

6. Select [LOCK] or [UNLOCK] by pressing the UP/ DOWN button and press the OK button.

- [UNLOCK] : Discards the protect function.

- [LOCK] : Sets up the PROTECT function. If you need to protect another image, press the LEFT/ RIGHT button.(In case of selecting [ONE PIC]

7. Press the shutter button and the menu will disappear. If you protect an image, the protect icon will be displayed on the LCD monitor. (An unprotected image has no indicator)

NOTICE

An image in LOCK mode will be protected from [DELETE] or [DELETE ALL] functions, but will NOT be protected from the [FORMAT] function.

BACK:

PLAY SETUP MyCAM

SET:OK

SLIDE

PROTECT

RESIZE

DEL. ALL

ONE PIC.

ALL PICS.

EXIT:MENU

PLAY SETUP MyCAM

PAGE:

SLIDE

PROTECT

RESIZE

DEL. ALL

OFF

LOCK

LOGO

EXIT:SHUTTER MOVE PIC. :

SET:OK

UNLOCK

Resize

The stored image size can be changed and used as logo image. The resized image will have a new file name.

NOTICE

Large sized images can be resized to be made smaller, but you may notice decreasing image quality when a small size image is resized to become larger. If you try to resize a Photo or Print size image, a [N/A] (Not available) sub menu will be displayed on the menu display. Only JPG images can be resized. TIFF, WAV files can’t be resized. The different compression format image, however the image(.JPG file) size is in the ratio of four to three(2048X1536, 1024X768, 512X384..etc), can’t be resized. Only 4:2:2 compression format file can be resized. The resized image will have a new file name. If the memory capacity is insufficient to store the resized image, [N/A] message will display on the LCD monitor and the resized image will not be stored. The start-up image is stored not on the memory card but on the internal memory.

1. Press the play mode button and select an image that you want to resize by pressing the LEFT/ RIGHT button.

2. Press the menu button.

Press the DOWN button and the cursor will be shifted to the main menu.

4. Select the [RESIZE] menu by pressing the UP/DOWN button.

5. Press the RIGHT button and the cursor will shift to the [RESIZE] sub menu.

6. Select the desired sub menu by pressing the UP/DOWN button.

7. Press the OK button to confirm the setting. Press the menu button twice and the menu display will disappear.

BACK:

PLAY SETUP MyCAM

SET:OK

SLIDE

PROTECT

RESIZE

DEL. ALL

1024x768

640x480

320x240

LOGO

EXIT:MENU

PLAY SETUP MyCAM

PAGE:

SLIDE

PROTECT

RESIZE

DEL. ALL

OFF

LOCK

LOGO

PLAY

Delete all

This enables you to clear all unprotected images from the memory.

NOTICE

Remember that this will permanently delete unprotected images. Important shots should be stored on a computer before deletion takes place.

1. Press the play mode button and press the menu button.

Press the DOWN button and the cursor will be shifted to the main menu.

3. Select the [DEL. ALL] menu by pressing the UP/DOWN button.

4. Press the RIGHT button and the cursor will shift to the [DEL. ALL] sub menu.

5. Select the desired sub menu by pressing the UP/DOWN button and press the OK button.

- Selecting [NO] : The display returns to the initial menu.

- Selecting [YES] :

A [PLEASE WAIT!] message will display and all the unprotected images are deleted. If there aren’t protected images, all the images are deleted and a [NO IMAGE!] message will display.

6. If you select [NO], press the menu button twice and the menu display will disappear. If a [NO IMAGE!] message is displayed on the LCD monitor after selecting [YES], press the play mode button or rotate the mode dial. The message will disappear.

BACK:

PLAY SETUP MyCAM

SET:OK

SLIDE

PROTECT

RESIZE

DEL. ALL

YES

EXIT:MENU

PLAY SETUP MyCAM

PAGE:

SLIDE

PROTECT

RESIZE

DEL. ALL

OFF

LOCK

LOGO

DPOF : Standard

DPOF(Digital Print Order Format) allows you to embed printing information on your memory card. Select the pictures to be printed and how many prints to make.(Print quantity : 0 ~ 30 ) The DPOF indicator will display on the LCD monitor when an image that has DPOF information plays back. Images can then be printed on DPOF printers, or at an increasing number of photo laboratories. This function is not available for Movie clips and WAV files.

This function allows you to embed print quantity information on a stored image.

1. Press the play mode button and select an image that you want to embed a print quantity by pressing the LEFT/ RIGHT button.

2. Press the menu button.

Press the DOWN button and the cursor will be shifted to the main menu.

4. Select the [DEL. ALL] menu by pressing the UP/DOWN button.

5. Press the DOWN button on the [DEL. ALL] menu and the next menu page will be displayed.

6. Select [STANDARD] menu by pressing the UP/DOWN button.

7. Press the RIGHT button and the cursor will shift to the [STANDARD] sub menu.

8. Select the desired sub menu by pressing the UP/DOWN button.

- [ONE PIC.] : Specifies the number of copies for a selected image. If you need to embed a print quantity on another image, press the LEFT/ RIGHT button.

- [ALL PICS.] : Specifies the number of copies for all images except for movie clips and voice recording files.

9. Press the OK button and a display to select the quantity will display on the LCD monitor.

10. Select the print quantity by pressing the UP/DOWN button.

11. Press the OK button to confirm the setting.

12. If an image carries DPOF instructions, the DPOF indicator ( ) will show. Press the shutter button and the camera working mode is turned to the play mode.

BACK:

PLAY SETUP MyCAM

SET:OK

STANDARD

INDEX

CANCEL

ONE PIC.

ALL PICS.

EXIT:SHUTTER MOVE PIC. :

SET:OK

00 PRINTS

PLAY

DPOF : Index

INFORMATION

The number of copy is 1. There is no indicator for the index print. If the index print was set, the [INDEX] sub menu will be displayed as [YES] on the LCD monitor. The first printed image is the first stored image.

This function will specify the number of copies (except for movie clips and sound clip) for index prints.

1. Press the play mode button and press the menu button.

Press the DOWN button and the cursor will be shifted to the main menu.

3. Select the [DEL. ALL] menu by pressing the UP/DOWN button.

4. Press the DOWN button on the [DEL. ALL] menu and the next menu page will be displayed.

5. Select [INDEX] menu by pressing the UP/DOWN button.

6. Press the RIGHT button and the cursor will shift to the [INDEX] sub menu.

7. Select the desired sub menu by pressing the UP/DOWN button.

8. Press the OK button to confirm the setting. Press the menu button twice and the menu display will disappear.

BACK:

PLAY SETUP MyCAM

SET:OK

STANDARD

INDEX

CANCEL

YES

EXIT:MENU

PLAY SETUP MyCAM

PAGE:

SLIDE

PROTECT

RESIZE

DEL. ALL

OFF

LOCK

LOGO

DPOF : Cancel

This is used for canceling the STANDARD or INDEX DPOF function.

1. Press the play mode button and press the menu button.

Press the DOWN button and the cursor will be shifted to the main menu.

3. Select the [DEL. ALL] menu by pressing the UP/DOWN button.

4. Press the DOWN button on the [DEL. ALL] menu and the next menu page will be displayed.

5. Select [CANCEL] menu by pressing the UP/DOWN button.

6. Press the RIGHT button and the cursor will shift to the [CANCEL] sub menu.

7. Select the desired sub menu by pressing the UP/DOWN button.

- [STANDARD] : Pre-set print quantity is canceled.

- [INDEX] : Index print is canceled.

8. Press the menu button twice and the menu display will disappear.

BACK:

PLAY SETUP MyCAM

SET:OK

STANDARD

INDEX

CANCEL

STANDARD

INDEX

EXIT:MENU

PLAY SETUP MyCAM

PAGE:

SLIDE

PROTECT

RESIZE

DEL. ALL

OFF

LOCK

LOGO

PLAY

Setup menu

Main menu Sub meun Secondary menu

FILE RESET

SERIES POWER OFF (Default : 3 MIN) LANGUAGE ENGLISH FRENCH

KOREAN ITALIAN

CHINESE 1 DUTCH

CHINESE 2 DANISH

JAPANESE FINNISH

RUSSIAN SWEDISH

GERMANY PORTUGUESE

SPANISH FORMAT NO

YES DATA SET

TIME SET 12:00 AM/PM DATE TYPE 'YY/MM/DD

MM/DD/'YY

DD/MM/'YY IMPRINT OFF

DATE

DATE&TIME SOUND ON

OFF LCD BRIGHTNESS LOW

NORMAL

HIGH VIDEO OUT NTSC

PAL QUICK VIEW

DEL.ANSWER OFF

In this mode, you can set up basic settings. Every camera working mode has [SETUP] tab in their own menu.

OFF / 1~10MIN

2003/01/01

OFF/ 1~3SEC.

File

This enables you to name files

1. Press the menu button and press the RIGHT button to select [SETUP](Second) tab.

Press the DOWN button and the cursor will be shifted to the main menu.

3. Select the [FILE] menu by pressing the UP/DOWN button.

Press the RIGHT button and the cursor will shift to the [FILE] sub menu.

5. Select the desired sub menu by pressing the UP/DOWN button.

- [RESET] : Using reset, the next file name will be set from 0001 even after formatting, deleting all or inserting a new memory card.

- [SERIES] : Under this system, the file name will directly follow the last stored file name, regardless of any actions such as file deletion or formatting.

6. Press the OK button to confirm the setting. Press the menu button twice and the menu display will disappear.

INFORMATION

The first stored folder name is 100SSCAM, and first name is SV300001. Whenever you store an image, the file number is increased by 1. The file number is named from SV300001 to SV309999 automatically, 9999 files will be stored in a folder. Using SERIES, the sequence starts at 100SSCAM and increases in increments of 1.(e.g : 101SSCAM, 102SSCAM…) The files used with the memory card conform to the DCF(Design rule for Camera File system) format.

BACK:

PLAY SETUP MyCAM

SET:OK

FILE

PWR OFF

LANGUAGE

FORMAT

RESET

SERIES

EXIT:MENU

PLAY SETUP MyCAM

PAGE:

FILE

PWR OFF

LANGUAGE

FORMAT

SERIES

OFF

ENGLISH

PLAY

Power off

This function switches the camera off after a set amount of time in order to prevent unnecessary battery drainage.

1. Press the menu button and press the RIGHT button to select [SETUP](Second) tab.

Press the DOWN button and the cursor will be shifted to the main menu.

3. Select the [PWR OFF] menu by pressing the UP/DOWN button.

4. Press the RIGHT button and the cursor will shift to the [PWR OFF] sub menu.

5. Select the desired sub menu by pressing the UP/DOWN button.

- Selecting [OFF] : The power off function will not operate.

- Selecting [ON] : A menu will be displayed on the LCD monitor as shown alongside.

6. Select the desired time by pressing the UP/DOWN button.

7. Press the OK button to confirm the setting. Press the menu button twice and the menu display will disappear.

INFORMATION

Even if the batteries or AC adapter are removed and inserted again, the power off setting will be preserved. Note that the automatic power off does not operate if the camera is in slide show or PC mode.

BACK:

PLAY SETUP MyCAM

SET:OK

FILE

PWR OFF

LANGUAGE

FORMAT

OFF

BACK:

PLAY SETUP MyCAM

SET:OK

FILE

PWR OFF

LANGUAGE

FORMAT

01 MIN

EXIT:MENU

PLAY SETUP MyCAM

PAGE:

FILE

PWR OFF

LANGUAGE

FORMAT

SERIES

OFF

ENGLISH

INFORMATION

The default language is ENGLISH. You can select 15 languages. Those are listed below. English, Korean, T. Chinese, S. Chinese, Japanese, Russian, Germany, Spanish, French, Italian, Portuguese, Danish, Swedish, Finnish, Dutch. Even if the camera is restarted, the language setting will be maintained. Even if the [SOUND] function is [ON], the sound will not activate in this menu.

There is a choice of languages that can be displayed on the LCD monitor.

Language

1. Press the menu button and press the RIGHT button to select [SETUP](Second) tab.

Press the DOWN button and the cursor will be shifted to the main menu.

Select the [LANGUAGE] menu by pressing the UP/DOWN button.

4. Press the RIGHT button and the cursor will shift to the [LANGUAGE] sub menu.

5. Select the desired sub menu by pressing the UP/DOWN button.

6. Press the OK button to confirm the setting. Press the menu button and the menu display will disappear.

EXIT:MENU

PLAY SETUP MyCAM

PAGE:

FILE

PWR OFF

LANGUAGE

FORMAT

SERIES

OFF

ENGLISH

BACK:

PLAY SETUP MyCAM

SET:OK

FILE

PWR OFF

LANGUAGE

FORMAT

ENGLISH

PLAY

Format

This is used for formatting the memory card.

1. Press the menu button and press the RIGHT button to select [SETUP](Second) tab.

2. Press the DOWN button and the cursor will be shifted to the main menu.

3. Select the [FORMAT] menu by pressing the UP/DOWN button.

4. Press the RIGHT button and the cursor will shift to the [FORMAT] sub menu.

5. Select the desired sub menu by pressing the UP/DOWN button.

- Selecting [NO] : The image will be displayed on the LCD monitor. Press the menu button twice and the menu display will disappear.

- Selecting [YES] : The memory card is formatted. (A [NO IMAGE !] message will be displayed after formatting in play mode)

INFORMATION

Before using the memory card, it must be initialized.

- New memory card, unformatted memory card.

- A memory card that has a file this camera can’t recognize or one that has been taken from another camera.

NOTICE

All the files in the memory are deleted by the [FORMAT] function. Before formatting the memory, it is advisable to copy important data onto other media as back-up e.g. floppy disks, hard disks, CD etc. Do not use the memory card formatted by another digital camera or memory card reader.

BACK:

PLAY SETUP MyCAM

SET:OK

FILE

PWR OFF

LANGUAGE

FORMAT

YES

EXIT:MENU

PLAY SETUP MyCAM

PAGE:

FILE

PWR OFF

LANGUAGE

FORMAT

SERIES

OFF

ENGLISH

Format

NOTICE

When you format the memory card in your PC that runs on Windows 2000 or XP, please select the FAT file system.

Formatting on a PC

1. Select [Removable Disk] in the [Windows Explorer].

2. Press the right mouse button and select [Format].

3. Select [FAT] file format type and click the [Start] button.

PLAY

Date set

You can change the imprinted date.

1. Press the menu button and press the RIGHT button to select [SETUP](Second) tab.

Press the DOWN button and the cursor will be shifted to the main menu.

3. Select the [FORMAT] menu by pressing the UP/DOWN button.

4. Press the DOWN button on the [FORMAT] menu and the next menu page will be displayed.

5. Select the [DATE SET] menu by pressing the UP/DOWN button.

6. Press the RIGHT button and the cursor will shift to the [DATE SET] sub menu.

7. Select the desired sub menu by pressing the UP/DOWN button. RIGHT button : selects YEAR/ MONTH/ DAY item. UP/ DOWN button : changes the value of each item.

8. Press the OK button to confirm the setting. Press the menu button twice and the menu display will disappear.

EXIT:MENU

PLAY SETUP MyCAM

PAGE:

FILE

PWR OFF

LANGUAGE

FORMAT

SERIES

OFF

ENGLISH

MOVE:

PLAY SETUP MyCAM

CHANGE:

‘03/01/01

03:58 PM

YY/MM/DD

OFF

DATE SET

TIME SET

D.TYPE

IMPRINT

BACK:

PLAY SETUP MyCAM

SET:OK

DATE SET

TIME SET

D.TYPE

IMPRINT

YEAR

03 /01/01

You can change the imprinted time.

Time set

1. Press the menu button and press the RIGHT button to select [SETUP](Second) tab.

2. Press the DOWN button and the cursor will be shifted to the main menu.

Select the [FORMAT] menu by pressing the UP/DOWN button.

4. Press the DOWN button on the [FORMAT] menu and the next menu page will be displayed.

5. Select [TIME SET] menu by pressing the UP/DOWN button.

6. Press the RIGHT button and the cursor will shift to the [TIME SET] sub menu.

Select the desired sub menu by pressing the UP/DOWN button. RIGHT button : selects HOUR, MINUTE, AM/PM item. UP/ DOWN button : changes the value of each item.

8. Press the OK button to confirm the setting. Press the menu button twice and the menu display will disappear.

BACK:

PLAY SETUP MyCAM

SET:OK

DATE SET

TIME SET

D.TYPE

IMPRINT

MOVE:

PLAY SETUP MyCAM

CHANGE:

DATE SET

TIME SET

D.TYPE

IMPRINT

‘03/01/01

03:58 PM

YY/MM/DD

OFF

EXIT:MENU

PLAY SETUP MyCAM

PAGE:

FILE

PWR OFF

LANGUAGE

FORMAT

SERIES

OFF

ENGLISH

HOUR

03 : 58 PM

PLAY

Date type

You can select date type that is imprinted on the image.

1. Press the menu button and press the RIGHT button to select [SETUP](Second) tab.

Press the DOWN button and the cursor will be shifted to the main menu.

3. Select the [FORMAT] menu by pressing the UP/DOWN button.

4. Press the DOWN button on the [FORMAT] menu and the next menu page will be displayed.

5. Select [D.TYPE] menu by pressing the UP/DOWN button.

6. Press the RIGHT button and the cursor will shift to the [D.TYPE] sub menu.

7. Select the desired sub menu by pressing the UP/DOWN button. ‘YY/ MM/ DD: Year/ Month/ Day MM/ DD/ ‘YY: Month/ Day/ Year DD/ MM/ ‘YY: Day/ Month/ Year

8. Press the OK button to confirm the setting. Press the menu button twice and the menu display will disappear.

BACK:

PLAY SETUP MyCAM

SET:OK

DATE SET

TIME SET

D.TYPE

IMPRINT

YY/MM/DD

MM/DD/

DD/MM/

EXIT:MENU

PLAY SETUP MyCAM

PAGE:

FILE

PWR OFF

LANGUAGE

FORMAT

SERIES

OFF

ENGLISH

Imprint

There is an option to include DATE/TIME on still images.

1. Press the menu button and press the RIGHT button to select [SETUP](Second) tab.

2. Press the DOWN button and the cursor will be shifted to the main menu.

3. Select [FORMAT] menu by pressing the UP/DOWN button.

4. Press the DOWN button on the [FORMAT] menu and the next menu page will be displayed.

5. Select the [IMPRINT] menu by pressing the UP/DOWN button.

6. Press the RIGHT button and the cursor will shift to the [IMPRINT] sub menu.

7. Select the desired sub menu by pressing the UP/DOWN button.

- OFF :

DATE & TIME will not be stamped on the image file.

- DATE : Only DATE will be stamped on the image file.

- DATE&TIME : DATE & TIME will be stamped on the image file.

8. Press the OK button to confirm the setting. Press the menu button twice and the menu display will disappear.

INFORMATION

Date & Time are imprinted at the bottom right side of the LCD monitor. Date will be imprinted as DATE TYPE setting. TIME is imprinted in the following way : [Hour / Minute/ Second] and hours are shown using the 12 hour clock. The imprint function is unaffected by the camera being switched on and off. Date & Time is imprinted as you set it in the DATE SET, TIME SET menu. The imprint function is applied only to the still image.

BACK:

PLAY SETUP MyCAM

SET:OK

DATE SET

TIME SET

D.TYPE

IMPRINT

OFF

DATE

DATE&TIME

EXIT:MENU

PLAY SETUP MyCAM

PAGE:

FILE

PWR OFF

LANGUAGE

FORMAT

SERIES

OFF

ENGLISH

PLAY

Sound

A beep will sound when you press the camera button and an error takes place. You can check the camera condition with this function.

1. Press the menu button and press the RIGHT button to select [SETUP](Second) tab.

Press the DOWN button and the cursor will be shifted to the main menu.

3. Select the [FORMAT] menu by pressing the UP/DOWN button.

4. Press the DOWN button on the [FORMAT] menu and the next menu page will be displayed.

5. Select the [IMPRINT] menu by pressing the UP/DOWN button.

6. Press the DOWN button on the [IMPRINT] menu and the next menu page will be displayed.

7. Select the [SOUND] menu by pressing the UP/DOWN button.

8. Press the RIGHT button and the cursor will shift to the [SOUND] sub menu.

9. Select the desired sub menu by pressing the UP/DOWN button.

- [ON] : The sound function is activated.

- [OFF] : The sound function is not activated.

10. Press the OK button to confirm the setting.

Press the menu button twice and the menu display will disappear.

INFORMATION

Even though the SOUND function is set to [OFF], you can hear Movie clip, voice memo and sound clip file.

BACK:

PLAY SETUP MyCAM

SET:OK

SOUND

LCD

VIDEO

Q.VIEW

OFF

EXIT:MENU

PLAY SETUP MyCAM

PAGE:

FILE

PWR OFF

LANGUAGE

FORMAT

SERIES

OFF

ENGLISH

LCD brightness

You may adjust the LCD brightness

1. Press the menu button and press the RIGHT button to select [SETUP](Second) tab.

Press the DOWN button and the cursor will be shifted to the main menu.

3. Select the [FORMAT] menu by pressing the UP/DOWN button.

4. Press the DOWN button on the [FORMAT] menu and the next menu page will be displayed.

5. Select the [IMPRINT] menu by pressing the UP/DOWN button.

6. Press the DOWN button on the [IMPRINT] menu and the next menu page will be displayed.

7. Select [LCD] menu by pressing the UP/DOWN button.

Press the RIGHT button and the cursor will shift to the [LCD] sub menu.

Select the desired sub menu by pressing the UP/DOWN button. There are LOW, NORMAL and HIGH sub menu in the [LCD] menu.

10. Press the OK button to confirm the setting.

Press the menu button twice and the menu display will disappear.

BACK:

PLAY SETUP MyCAM

SET:OK

SOUND

LCD

VIDEO

Q.VIEW

DARK

NORMAL

BRIGHT

EXIT:MENU

PLAY SETUP MyCAM

PAGE:

FILE

PWR OFF

LANGUAGE

FORMAT

SERIES

OFF

ENGLISH

PLAY

Video

INFORMATION

Select the correct movie standard for the outer monitor. PAL mode can support only BDGHI NTSC : U.S.A, Canada, Japan, South Korea, Taiwan, Mexico. PAL : Australia, Austria, Belgium, China, Denmark, Finland, Germany, U.K., Holland, Italy,

Kuwait, Malaysia, New Zealand, Singapore, Spain, Sweden, Switzerland, Thailand, Norway.

Even if the [SOUND] function is [ON], the sound will not activate in this menu.

The Movie output signal from the camera can be NTSC or PAL. Your choice of output will be governed by the type of machine (monitor or TV, etc.) to which the camera is connected.

1. Press the menu button and press the RIGHT button to select [SETUP](Second) tab.

Press the DOWN button and the cursor will be shifted to the main menu.

3. Select the [FORMAT] menu by pressing the UP/DOWN button.

4. Press the DOWN button on the [FORMAT] menu and the next menu page will be displayed.

5. Select the [IMPRINT] menu by pressing the UP/DOWN button.

6. Press the DOWN button on the [IMPRINT] menu and the next menu page will be displayed.

7. Select [VIDEO] menu by pressing the UP/DOWN button.

8. Press the RIGHT button and the cursor will shift to the [VIDEO] sub menu.

9. Select the desired sub menu by pressing the UP/DOWN button.

10.

Press the OK button to confirm the setting. Press the menu button twice and the menu display will disappear.

BACK:

PLAY SETUP MyCAM

SET:OK

SOUND

LCD

VIDEO

Q.VIEW

NTSC

PAL

EXIT:MENU

PLAY SETUP MyCAM

PAGE:

FILE

PWR OFF

LANGUAGE

FORMAT

SERIES

OFF

ENGLISH

Connecting to an external monitor

Connecting to an external monitor In RECORDING/ PLAY mode, you can view the stored still images or movie clips by connecting the camera to an external monitor via the video cable. When the camera is connected to an external monitor, the LCD monitor will be turned off automatically.

INFORMATION

When using a TV as an external monitor, you will need to select the external or AV channel of the TV. There will be a digital noise on the external monitor, but it is not a malfunction. If the image is not in the centre of the screen, use the TV controls to centre it. When the camera is connected to an external monitor, the menu will be visible on the external monitor and the menu functions are the same as those indicated on the LCD monitor.

PLAY

Quick view

You can briefly review the last image captured during the pre-set time.

1. Press the menu button and press the RIGHT button to select

[SETUP](Second) tab.

2. Press the DOWN and the cursor will be shifted to the main menu.

3. Press the DOWN button until the [Q. VIEW] menu is selected.

4. Press the RIGHT button and the cursor will shift to the [Q.VIEW]

sub menu.

5. Select the desired sub menu by pressing the UP/DOWN button.

- [OFF] : The quick view function can’t be activated.

- [1 ~ 3 SEC] : The captured image is briefly displayed during the selected time.

6. Press the OK button to confirm the setting. Press the menu button twice and the menu display will be disappeared.

* Setting up the [DEL, ANSWER] function

If you select [1~3SEC] sub menu at the step 5, press the RIGHT button and the [DEL. ANSWER] menu will be displayed. Select the desired [DEL. ANSWER] sub menu by pressing the UP/DOWN button.

- Selecting [OFF] : A [DEL. ANSWER] message will not display.

- Selecting [ON] : You can delete the captured image at once.

* Using the [DEL.ANSWER] menu

If you select [ON] at the [DEL.ANSWER] menu, a message as shown alongside will be displayed after taking a picture.

- Selecting [YES] : the captured image is deleted.

- Selecting [NO] : the captured image is stored.

INFORMATION

The quick view function doesn’t apply to the movie clip and sound clip file. [Q.VIEW] function is not adjusted to the TIFF file type.

BACK:

PLAY SETUP MyCAM

SET:OK

SOUND

LCD

VIDEO

Q.VIEW

1 SEC

BACK:

PLAY SETUP MyCAM

SET:OK

SOUND

LCD

VIDEO

Q.VIEW

DEL.ANSWER

OFF

EXIT:MENU

PLAY SETUP MyCAM

PAGE:

FILE

PWR OFF

LANGUAGE

FORMAT

SERIES

OFF

ENGLISH

1. Press the menu button and press the RIGHT button twice to select [My CAM](Third) tab.

Press the DOWN button and the cursor will be shifted to the main menu.

3. Select the [S. IMAGE] menu by pressing the UP/DOWN button.

4. Press the RIGHT button and the cursor will shift to the [S. IMAGE] sub menu.

5. Select the desired sub menu by pressing the UP/DOWN button.

6. Press the OK button to confirm the setting. Press the menu button twice and the menu display will disappear.

NOTICE

Only a image that is save as a LOGO at the [RESIZE] sub menu can be used as the USER IMAGE. If the USER IMAGE was not saved, no image will be displayed on the LCD monitor at the time of camera power on. Refer to p.74 for selecting the USER IMAGE. The USER IMAGE will not be deleted by the [DEL.ALL] or [FORMAT] menu.

MyCAM menu

You can set up a start up image, start up sound and shutter sound. Every camera working mode has the My CAM menu

Start up image

You can select the image that is first displayed on the LCD monitor whenever the camera is turned on.

MOVE:

PLAY SETUP MyCAM

CHANGE:

S.IMAGE

S.SOUND

SH.SOUND

IMAGE2

SOUND1

SH.SOUND1

BACK:

PLAY SETUP MyCAM

SET:OK

S.IMAGE

S.SOUND

SH.SOUND

IMAGE 2

PLAY

Start up sound

You can select the sound that is activated whenever the camera is turned on.

1. Press the menu button and press the RIGHT button twice to select [MyCAM](Third) tab.

Press the DOWN button and the cursor will be shifted to the main menu.

3. Select the [S. SOUND] menu by pressing the UP/DOWN button.

4. Press the RIGHT button and the cursor will shift to the [S. SOUND] sub menu.

5. Select the desired sub menu by pressing the UP/DOWN button.

6. Press the OK button to confirm the setting. Press the menu button twice and the menu display will disappear.

1. Press the menu button and press the RIGHT button twice to select [MyCAM](Third) tab.

Press the DOWN button and the cursor will be shifted to the main menu.

Select the [SH. SOUND] menu by pressing the UP/DOWN button.

4. Press the RIGHT button and the cursor will shift to the [SH. SOUND] sub menu.

5. Select the desired sub menu by pressing the UP/DOWN button.

6. Press the OK button to confirm the setting. Press the menu button twice and the menu display will disappear.

Shutter sound

You can select the shutter sound.

MOVE:

PLAY SETUP MyCAM

CHANGE:

S.IMAGE

S.SOUND

SH.SOUND

IMAGE2

SOUND1

SH.SOUND1

BACK:

PLAY SETUP MyCAM

SET:OK

S.IMAGE

S.SOUND

SH.SOUND

OFF

SOUND1

SOUND2

SOUND3

BACK:

PLAY SETUP MyCAM

SET:OK

S.IMAGE

S.SOUND

SH.SOUND

OFF

SH. SOUND1

SH. SOUND2

SH. SOUND3

MOVE:

PLAY SETUP MyCAM

CHANGE:

S.IMAGE

S.SOUND

SH.SOUND

IMAGE2

SOUND1

SH.SOUND1

List of camera function

SIZE Print(Photo / Super Fine) ( )- - - - - - - - - - - -

Memo(Middle / Fine) -- - ----- -- -E-mail (Small / Normal) -- - ----- -- -Large ( ) ( ) ( ) ( ) ( ) ( )- ( )- - - Photo - ---Middle - ---Small - ---320 x 240pixels - - - - - - - ( )- - - - -

QUALITY Tiff (1:1) - ----

Super Fine(1:4) - ---Fine (1:8) ( ) ( ) ( ) ( ) ( ) ( )- ( )- - - Normal (1:12) - ---1:12 - - - - - - - ( )- - - - -

ZOOM Optical ZOOM ----

Digital ZOOM - -

METERING

Multi-Pattern ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( )- - - Spot ----

FOCUS AF ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( )- - - -

MF (indicator) ----

SHOOTING

Single ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( )- - - Continuous ---AEB ----

ISO AUTO ( ) ( ) ( ) ( ) ( )- - - -

100 ( ) ( ) ( ) -- -200 ---400 ----

W.BALANCE

Auto ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( )- - - Daylight ---Cloudy ---Fluorescent ---Tungsten ----

EFFECT Normal ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( )- - - -

B&W ---sRGB ---Sunset ----

SHARPNESS

Soft ---Normal ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( )- - - Vivid

----

MODE DIAL

Function

: Default, : After restarting the camera, : Selectable , X: Not Available, -: Not Selectable

PLAY

List of camera function

FLASH Auto ( ) ( )- - - -

Red eye (with Auto) ( ) ( ) ---Fill-in ---Slow sync.(with Red eye) ( ) -- -Off ( ) ( ) ( ) ( ) ----

EVC -0.5 ~ -2.0EV (1/2 EV step) ----

0.0EV ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( )- - - +0.5 ~ +2.0EV (1/2 EV step)

----

SELFTIMER

Off ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( )- - - 2 sec. -- -10 sec. ----

Remote control ---AF Normal (80cm ~ ∞) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( )- - - - ZONE Macro (30 ~80cm) ----

Super Macro (6 ~30cm) ---AUDIO Off ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( )- - - (Voice memo)

On ( ) ---A/S/M

A/S/M (A) (P) - - - SET

(F5.6)(F5.6)(F5.6)

----

(1/250) (1/250)

(1/250)

----

SLIDE SHOW

OFF /1~10 sec.(1sec step) - - - - - - - - - - (OFF)

Repeat Off - - - - - - - - - - ( )

Repeat On - - - - - - - - - PROTECT Unlock - - - - - - - - - - ( )

Lock - - - - - - - - - DPOF Index (1 print) - - - - - - - - - -

Standard (0 ~30 prints) - - - - - - - - - EDIT Trimming - - - - - - - - - -

Resize - - - - - - - - - DELETE ALL - - - - - - - - FILE NAME

Reset ( )

Series POWER OFF

OFF /1~10 min. (3 min) LANGUAGE

15 Languages (English) DATE 2002.01.01 ~2050.12.31

(2003.01.01 )

MODE DIAL

Function

List of camera function

IMPRINT Off ( )

Date

Date &Time

DATE TYPE YYYY/MM/DD ( )

DD/MM/YYYY

MM/DD/YYYY

SOUND EFFECT On ( )

Off

START-UP IMAGE

Off

IMAGE 1 ( )

IMAGE 2

IMAGE 3

USER IMAGE

START-UP SOUND

Off

SOUND 1 ( )

SOUND 2

SOUND 3

SHUTTER SOUND

Off

SH.SOUND 1 ( )

SH.SOUND 2

SH.SOUND 3

LCD BRIGHTNESS

0 ~2 Level (1 Level )

VIDEO OUT NTSC ( )

PAL

QUICK VIEW Off /1~3 sec (1 sec)

Delete answering On

Delete answering Off

( )

MODE DIAL

Function

PLAY

Starting PC mode

If you insert the USB cable into the USB connection terminal, the camera working mode will change to the PC mode automatically. In this mode, you can download stored images to your PC through the USB cable. The LCD monitor is always turned off in PC mode. The autofocus indicator lamp(red) lamp blinks when the files are transferring via the USB connection.

Connecting the camera to PC

1. Turn the PC power on.

2. Turn the camera power on.

3. Connect the PC and the camera via the USB cable.

- Insert the small plug of the USB cable into the camera USB connection terminal.

- Insert the large connector of the USB cable into the USB port of the PC

- The plugs must be firmly inserted.

Disconnecting the camera and PC Refer to the following page

- WIN 98SE : p.119

- WIN 2000/ME/XP : p.119

INFORMATION

The camera driver must be installed before using PC mode. To save battery power, it is recommended that you use an AC adaptor(Optional) when connecting the camera to a computer.

100

Downloading stored images Once you have downloaded images to your PC, they can be edited and printed.

Starting PC mode

1. Connect the camera to your PC with the USB cable.

2. On your computer’s desktop display, select [My computer] and double click [Removable Disk DCIM 100SSCAM]. The image files will then be displayed.

3. Select an image and press the right mouse button.

4. A pop-up menu will open. Click [Cut] or [Copy] menu [Cut] : cuts a selected file. [Copy] : copies files.

5. Click a folder that you want to paste the file.

6. Press the right mouse button and a pop-up menu will open. Click [Paste].

7. An image file is transferred from camera to your PC.

- By using [Digimax Viewer], you can see the stored images in the memory directly on the PC monitor and you can copy or move the image files.

101

PLAY

Important notes

Your new Samsung camera is a precision instrument. Whilst it is designed to withstand general wear and tear, there are some important points that will help you get maximum service and reliability from your camera. The following should be avoided :

- Severe changes in temperature and humidity.

- Dust and dirt.

- Direct sunlight or the inside of a vehicle in hot weather.

- Environments where there is high magnetism or excessive vibration.

- Areas with high explosives or which are highly flammable materials.

- Pesticides, etc. Sand can be particularly troublesome to cameras.

- Sand or other small particulates can cause severe malfunctions. Ensure that there is no contact with sand or similar particles.

Extremes in temperature may cause problems.

- If the camera is transferred from a cold to a warm and humid environment, condensation can form on the delicate electronic circuitry. If this occurs, turn the camera off and wait for at least 1 hour until all moisture is dispersed. Moisture build up can also occur in the MEMORY CARD. If this happens, turn off the camera and remove the MEMORY CARD. Wait until the moisture has dispersed.

If the digital camera is not used for a long period, an electric discharge can occur. It is a good idea to remove the batteries and the MEMORY CARD, the camera is not used for some time. If the camera is exposed to electronic interference, it will turn itself off to protect the MEMORY CARD. Maintenance

- Use a soft brush (available from photo stores) to GENTLY clean the lens and LCD assemblies. If this does not work, lens-cleaning paper with lens cleaning fluid can be used.

- Clean the camera body with a soft cloth. Do not allow this camera to come into contact with solvent materials such as benzol, insecticide, thinners etc. This may damage the body shell of the camera and also affect its performance.

- Rough handling can damage the LCD monitor. Take care to avoid damage and keep the camera in its protective carry case at all times when not in use.

DO NOT attempt to disassemble or modify the camera. It contains delicate parts and there are high voltage circuits that can cause electric shocks. Under certain conditions, static electricity can cause the flash unit to fire. This is not harmful to the camera and is not a malfunction. When images are uploaded or downloaded, the data transfer may be affected by static electricity. In this case, disconnect and re-connect the USB cable before trying the transfer again.

Hanwha Techwin DIGIMAXV3 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual