HANTRONIX HDA570S-H Datasheet

Download

PRODUCT SPECIFICATION

HDA570S-H

5.7”, TFT QVGA COLOR LCD DISPLAY MODULE

HANTRONIX, INC.

10080 BUBB RD.

CUPERTINO, CA 95014

Q.A.: REV.:

ZW 1.0

HDA570S-H

SHEET 1 OF 15

DATE:

12/18/06

4. Application

This specification is applied to the 5.7 inch QVGA supported TFT-LCD module, and

can display true 262,144 colors(6 bit/ color). The module is designed for OA, Car TV

application and other electronic products which require flat panel display of digital signal

interface.This module is composed of a 5.7”TFT-LCD panel,a driver circuit and backlight

unit.

5. Features

- QVGA (320×240 pixels) resolution.

- Digital 18 bit parallel RGB.

- Line inversion mode with stripe type.

- Both DE mode and SYNC mode are supported for digital RGB input data format.

- Luminance

800 cd/m

6. General Specifications

Item Specifications Unit Screen Size 5.7 (Diagonal) inch Display Format 320RGB(H)×240(V) dot Active Area 115.2(H)×86.4(V) mm Dot Size 0.120(H)×0.360(V) mm Pixel Configuration RGB Vertical Stripe -

TN Type

Display Mode

Transmissive Mode

Normally White

Surface Treatment

Viewing Direction 12 O’clock Outline Dimension 144.0(W)×104.6(H)×13.0(D) mm Weight 192 g

Touch Screen optional.

HANTRONIX, INC.

10080 BUBB RD.

CUPERTINO, CA 95014

Q.A.: REV.:

Z.W.

1.0

Hard Coat + Anti-Glare

+ Wide View film

HDA570S-H

SHEET 2 OF 15

DATE:

12/18/06

7. Absolute Maximum Ratings

7.1 Absolute Ratings of Environment

Item Symbol

Va l u e

Min. Max.

Unit Note

Storage Temperature T Operating Ambient Temperature T

-30 +80 °C (1)

-20 +70 °C (1)

Note (1) Temperature and relative humidity range are shown in the figure below.

(a)90%RHMax.(Ta < 40°C).

(b) Wet-bulb temperature should be 39°C Max. (Ta>40°C).

7.2 Electrical Absolute Ratings

7.2.1 TFT-LCD Module

(Ta=25±

Va l u e

Item Symbol

Min. Max.

Digital Power Supply Voltage VCC -0.3 4.3 V -

7.2.2 Backlight Unit

Va l u e

Item Symbol

Min. Max.

2°C, GND=VSS=0V)

Unit Note

(Ta=25± 2°C)

Unit Note

Lamp current IL

Note (1) Permanent damage to the device may occur if maximum values are exceeded

or reverse voltage is loaded.

HANTRONIX, INC.

10080 BUBB RD.

CUPERTINO, CA 95014

Q.A.: REV.:

Z.W.

1.0

- 7.0 mA (1)

SHEET 3 OF 15

HDA570S-H

DATE:

12/18/06

8. Electrical Characteristics

8.1 TFT-LCD Module

(Ta=25± 2°C)

Item Symbol

Power Supply Voltage VCC 3.0 3.3 3.6 V -

Input High Threshold Voltage VIH 0.7VCC -

Input Low Threshold Voltage VIL 0 - 0.3 VCC V-

Power Consumption P

Frame Frequency F

Dot Clock DCLK - 6.4 7 MHz -

Min. Typ. Max.

(0.24) W (1)

-60-Hz-

Value

VCC

Unit Note

V-

Note (1) The specified power consumption is under the conditions at VCC=3.3V,

=60Hz, whereas a power dissipation check pattern below is displayed.

Black Pattern / 0 Gray

HANTRONIX, INC.

10080 BUBB RD.

CUPERTINO, CA 95014

Q.A.: REV.:

Z.W.

1.0

Active Area

HDA570S-H

SHEET 4 OF 15

DATE:

12/18/06

8.2 Backlight Unit

Pin NO Pin Name Description Note

(Ta=25±2°C)

- NC This is electrically opened

Note (1)? Low voltage side of backlight inverter connects with ground of inverter circuits.

Parameter Symbol Min. Typ. Max. Unit Note

Lamp current IL 5.5 6.0 6.5 mArms

Lamp voltage VL 745 825 905 Vrms IL=6.0mA

Lamp frequency PL 20 50 80 KHz IL=6.0mA

Kick-off voltage(25? ) VS – 1235 Vrms IL=6.0mA

Kick-off voltage(-20? ) VS -- 2060 Vrms IL=6.0mA

Lamp Life Time FL 20000 -- -- hr IL=6.0mA

LOW

HIGH

Input terminal(Low voltage side) (1)

Input terminal(Hi voltage side)

(Ta=25±2°C)

HANTRONIX, INC.

10080 BUBB RD.

CUPERTINO, CA 95014

Q.A.: REV.:

Z.W.

1.0

HDA570S-H

SHEET 5 OF 15

DATE:

12/18/06

9. Block Diagram

9.1 TFT-LCD Module with Backlight Unit

R0~R5G0~G5 B0~B5 VCC VSS DEN CLK IHS IVS R/L U/D

TFT-LCD Panel (320RGBx240)

CCFL B/L UNIT

HANTRONIX, INC.

10080 BUBB RD.

CUPERTINO, CA 95014

Q.A.: REV.:

Z.W.

1.0

HDA570S-H

SHEET 6 OF 15

DATE:

12/18/06

10. Input / Output Terminals Pin Assignment

10.1 TFT-LCD Module

Pin No. Symbol I/O Description

1 VSS I Ground

2 CLK I Clock signal

3 IHS I Horizontal synchronous signal

4 IVS I Vertical synchronous signal

5 VSS I Ground

6 R0 I RED data (LSB)

7R1I

8R2I

9R3I

10 R4 I

11 R5 I RED data(MSB)

12 VSS I Ground

13 G0 I GREEN data(LSB)

14 G1 I

15 G2 I

16 G3 I

17 G4 I

18 G5 I GREEN data(MSB)

19 VSS I Ground

20 B0 I Blue data(LSB)

21 B1 I

22 B2 I

RED data

GREEN data

Blue data

23 B3 I

24 B4 I

25 B5 I

26 VSS I Ground

27 DEN I Input data enable control

28 VCC I +3.3V power supply

29 VCC I +3.3V power supply

30 R/L I

HANTRONIX, INC.

10080 BUBB RD.

CUPERTINO, CA 95014

Q.A.: REV.:

Z.W.

Blue data

Blue data(MSB)

Right-and-Left scan setting. (“H” : Normally , “L” : Right-and-Left reversal)

1.0

HDA570S-H

SHEET 7 OF 15

DATE:

12/18/06

Pin No. Symbol I/O Description

Up/down scan setting.

31 U/D

(“H”: normal scan. “L”: Up-and-Down reversal.)

32 NC

I No connection

33 VSS I Ground

10.2 Color Data Input Assignment

The brightness of each primary color(red, green and blue) is based on the

6 bit gray scale data input for the color. The higher the binary input, the brighter

the color. The table provides the assignment of color versus data input.

Color

Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Red 111111000000000000 Green 0 0 0 0 0 0 1 11111000000

Basic Colors

Gray Scale Of RED : : : : : : : ::::::::::::

Gray Scale Of Green : : : : : : : : : : : : : : : : : : :

GrayScaleOfBlue : ::::::::::::::::::

Blue 000000000000111111 Cyan 000000111111111111 Magenta 111111 000000111111 Yellow 111111111111000000 White 111111111111111111 Red(0)/Dark 000000000000000000 Red(1) 0 0 0 0 0 1 0 0 0 000000 0 00 Red(2) 0 0 0 0 1 0 0 0 0 000000 0 00

Red(61) 111101000000000000 Red(62) 1 1 1 1 1 0 0 0 0 00000 0 000 Red(63) 111111000000000000 Green(0) / Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Green(1) 000000000001000000 Green(2) 0 0 0 0 0 0 00001000 0 000

Green(61) 000000111101000000 Green(62) 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0 Green(63) 000000111111000000 Blue(0)/Dark 0 0 0 0 0 0 0 0000000 0 000 Blue(1) 000000000000000001 Blue(2) 0 0 0 0 0 0 0 0 0 00000 00 10

Blue(61) 000000000000111101 Blue(62) 0 0 0 0 0 0 0 00000111 110 Blue(63) 000000000000111111

D05 D04 D03 D02 D01 D00 D15 D14 D13 D12 D11 D10 D25 D24 D23 D22 D21 D20

Red Green Blue

Data Signal

HANTRONIX, INC.

10080 BUBB RD.

CUPERTINO, CA 95014

Q.A.: REV.:

Z.W.

1.0

HDA570S-H

SHEET 8 OF 15

DATE:

12/18/06

11. Interface Timing

11.1 Input Signal Characteristics

Digital Parallel RGB Interface (960×240 resolution)

HANTRONIX, INC.

10080 BUBB RD.

CUPERTINO, CA 95014

Q.A.: REV.:

Z.W.

1.0

HDA570S-H

SHEET 9 OF 15

DATE:

12/18/06

11.2 Waveform

11.2.1 Clock and Data Waveform

11.2.2 Clock and Sync waveforms

OSC

HANTRONIX, INC.

10080 BUBB RD.

CUPERTINO, CA 95014

Q.A.: REV.:

Z.W.

1.0

HDA570S-H

SHEET 10 OF 15

DATE:

12/18/06

11.2.3 IHS and horizontal control timing waveforms

DES

OEH

OEV

OKV

11.2.4 IHS and vertical shift clock timing waveforms

STV

SUV

11.2.5 IHS and vertical control timing waveforms

HANTRONIX, INC.

10080 BUBB RD.

CUPERTINO, CA 95014

Q.A.: REV.:

Z.W.

VSE

Vs1

1.0

HDA570S-H

SHEET 11 OF 15

DATE:

12/18/06

12. Optical Characteristics

The optical characteristics should be measured in a dark environment ( 1 lux)?

or equivalent state with the methods shown in Note (4).

Item

Contrast Ratio CR 300 (450) - - (2)

Response Time

Luminance(Center)

Brightness uniformity BUNI

Red

Green

Color

Chromaticity

Blue

White

Horizontal

Viewing Angle

Ve rt i ca l

Symbol

Y 800 (850) - cd/m

Rx -

Ry -

Gx -

Gy -

Bx -

By -

Wx -

ñx+

-ñ

ñY+

Conditions Min. Typ. Max. Unit Note

-15-ms

-35-ms

80 (85) -



=0ûY=0û

Viewing Normal

Angle

CR?10

(0.640)

(0.344)

(0.291)

(0.610)

(0.142)

(0.120)

(0.346)

55 (60) -

45 (50) -

35 (40) -

(0.381)

deg.

(3)

(4)

(5)

(1),(4)

HANTRONIX, INC.

10080 BUBB RD.

CUPERTINO, CA 95014

Q.A.: REV.:

Z.W.

1.0

HDA570S-H

SHEET 12 OF 15

DATE:

12/18/06

Note (4) Measurement Set-Up:

The LCD module should be stabilized at a given temperature for 30 minutes

to avoid abrupt temperature change during measuring. In order to stabilize

the luminance, the measurement should be executed after lighting Backlight

for 30 minutes in a windless room.

LCD Module

LCD Panel

Photometer

Center of the Screen

(TOPCON BM-7 Fast)

Field of View = 1º

Light Shield Room

(Ambient Luminance<1lux)

Note (5)

500 mm

Definition of brightness uniformity

B rightness uniformity Min Luminance of 9 points)/(Max Luminance of 9 points)

H/6

H/2

H/6

HANTRONIX, INC.

10080 BUBB RD.

CUPERTINO, CA 95014

W/6

W/2

Q.A.: REV.:

Z.W.

1.0

W/6

W/2

HDA570S-H

SHEET 13 OF 15

DATE:

12/18/06

HANTRONIX, INC.

10080 BUBB RD.

CUPERTINO, CA 95014

Q.A.: REV.:

Z.W.

1.0

HDA570S-H

SHEET 14 OF 15

DATE:

12/18/06

5. Mechanical Dimensions (Touch screen option)

HANTRONIX, INC.

10080 BUBB RD.

CUPERTINO, CA 95014

Q.A.: REV.:

Z.W.

1.0

HDA570S-H

HJST

SHEET 15 OF 15

DATE:

12/18/06

HANTRONIX HDA570S-H Datasheet

Specifications and Main Features

Frequently Asked Questions

User Manual