Hantel QOOLQEEX Users Manual

FCC ID : ODGQOOLQEEX

ATTACHMENT E.

- USER’S MANUAL -

REPORT NO. : HCT-F05-0603 HYUNDAI C–TECH

1/1

1

[TABLE OF CONTENTS]
Chapter 0 QUICK START

1. Power On / Off

2. Listening to music

3. Listening to radio

4. Charging the battery

Chapter 1 GETTING STARTED

1. Introduction

2. Copyrights and Certification

3. Registered Trademarks

4. Product Features

5. Package Contents
6 Product Overview

7. Button Operations

Chapter 2 BASIC OPERATIONS

1. Before installation

2. Installing software

- Install CD

3. Connecting the product to a PC

4. File Management using a removable disk

- File Upload / Download

- Format

5. Disconnecting the product from a PC

6. Firmware Upgrade

7. Mode Switch

Chapter 3 MP3 MODE

1. MP3 Play / Stop

2. Fast-forward / Rewind

4. REPEAT Mode Setup

5. LED On / Off

6. EQ

7.Volume Control

2

Chapter 4 FM RADIO MODE

1. How to scan

2. How to auto-scan

3. Changing channel

4. LED On / Off

5.Volume Control

Chapter 5 MISCELLANEOUS

1. General Cautions

2. Earphone-related Cautions

3. Battery-related Caution

4. Troublesho oti ng

5. Product Specifications

3

Chapter 0 QUICK START

1. Power On / Off

1) While the product is off, press and hold the

2) While the product is on, press and hold the

<Play / Pause> button to turn the power on.

<Play / Pause> button to turn the power off.

2. Listening to music

1) Press the

<Play / Pause> button briefly to play or stop music in MP3 mode.

3. Listening to radio

1)To enter FM RADIO mode, press and hold the

<Mode Change> button briefly.

Charging the battery

4.

The Qoolqee X can be charged by a PC and a USB adaptor.

If the device is connected to a PC that is powered on, or to a USB cable, it goes into USB CONNECT status and starts charging.
If the battery goes low, a red led will blink. After fully discharged, the device will turn off, automatically.

To charge the battery with your PC: After lifting the USB cover located at the bottom of the product as shown in the picture,
connect it to your PC via a USB cable.

4

While charging is in progress, the led is red, and led become blue when charging is complete. To fully charge,

it takes 3 hours and

the battery lasts for 10 hours.

To charge the battery with a USB adapter: After lifting the USB cover located at the bottom of the product, connect the USB
plug of an adapter that is connected to power to the USB port of the product.

(!!) The suitable adapter for Qoolqee X 5V, 1.2A.

5

Chapter 1 GETTING STARTED

1. Introduction

1) Qoolqee K7
Thank you for purchasing our product. This manual is provided for correct use of the product. Please read it

horoughly before using the product.

http://www.qoolqee.com

2) You can obtain product information, and also have your questions answered. By registering with the product

serial number indicated on the manual, you can receive online support from us, and upgrade firmware for
enhancement of the product’ s features.
The content of the manual may be revised according to product specifications at the time of
release. The revised manual may be downloaded via our web site.

2. Copyrights and Certification

1) The copyright of this manual is owned by Hantel Co., Ltd. Any unauthor ized duplication or distribution of all or
any part of the manual is prohibited.
WMA is the registered trademark of Microsoft corp.
The copyright of the Hantel MP3 software program is owned by Hantel Co., Ltd. and any unauthorized duplication,
distribution or commercial use of the program without the prior written consent of Hantel Co., Ltd. is against the
law. With th e exception of the right provided to the user specifically for use of the product, this manual does not
grant the user any other right to use patents, trademarks, copyrights or any other intellectual property rights owned
by Hantel Co., Ltd.

6

2) FCC Certification

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio / TV technician for help.

CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.

3. Registered Trademarks

1. Windows, Windows 98 SE, Windows ME, Windows 2000, Windows XP and Windows Media Player are the
registered trademarks of Microsoft Corp.

7

4. Product Features

z Light just like a feather -26g
z It was born for the outdoor sports-water resistance such as rain, sweat
z USB 2.0 High speed
z Support MP3, WMA, ASF, OGG (Q1~Q10)
z Random
z Edit your own Play List
z Resume
z Various EQs such as Normal, Rock, Jazz, Classic, Pop, Live
z User friendly UI
z FM Radio Listening
z Built-in Lithium Polymer Battery
z Firmware Upgradeable
z Use it as a Removable

disk

8

5. Package Contents

Main Unit, Install CD (including User’s manual), USB Cable , Quick Guide, Earphones, A/C adapter (Option)

[NOTE] The above components may change without prior notice for enhancement of product performance.

9

6. Product Over vi ew

X3

X2

1) Earphone Jack

2) Mode change

3) Volume +

4) Power On / Off

5) REW

6) LED

7) FF

8) Auto Scan / Shuffle

9) Volume –

10) EQ

11) USB Cover

12) X2: Clip for hang

X3: Band Clip

13) Reset button

10

7. How to use buttons

MP3 Mode

Button Name Press Short Press Long

Play / Pause Play / Pause Power On / Off

Mode Switch to the FM Mode LED On / Off

EQ EQ Change Move to the Normal EQ

Shuffle / Auto Scan Play in random Play in order

Volume + Increment the volume Increment the volume continuously

Volume - Decrement the volume Decrement the volume continuously

REW Move to the previous track Rewind (to the first part of the file).

FF Move to the next track Fast-forward (go ahead while pressing the

button.)

FM Radio Mode

Button Name Press Short Press Long

Play / Pause Play / Pause Power On / Off

Mode Switch to the MP3 Mode LED On / Off

EQ - -

Shuffle / Auto Scan Move to the next channel After auto scanning, move to the first

channel

Volume + Increment the volume Increment the volume continuously

Volume - Decrement the volume Decrement the volume continuously

REW Decrement 50KHz Previous channel scan

FF Increment 50KHz Next channel scan

11

LED

MP3 & FM Mode RED & BLUE LED blink alternately

Transmission Data A BLUE LED blinks continuously

Low Battery When the battery is low, a red LED blinks for a while. Then the device will not be functioned. After

that the device turns off.

Play -> Pause RED & BLUE LED Off

Pause -> Play RED & BLUE LED On

12

Chapter 2 BASIC OPERATIONS

1. Before installation

Minimum requirements for software installation

z Pentium 133 MHz or above
z Windows 98SE / ME / 2000 / XP
z More than 20 MB of available hard disk space
z CD-ROM drive
z USB port support

(!) For Windows 2000 systems, you must log in to an account with administrator privileges for software

installation.

(!!)The USB driver is automatically installed for Windows 98SE users when installing the program using

the master CD, and may be recognized without installing a separate drive in Windows ME/2000/XP.

2) USB driver confirmation method

● Windows 98SE : Control Panel → System → Device Manager → General Serial Bus Controller

● Windows 2000 : Control Panel → System → Hardware → Device Manager → General Serial Bus Controller

● Windows XP : Control Panel → Performance and Maintenance → System → Hardware → Device Manager
→ General Serial Bus Controller

13

2. Installing software

- Install CD

1) Insert the installation CD into the CD-ROM drive.

2) Choose "Next" in the windows that follow.

14

3. Connecting the product to a PC

1) Connect the USB port of the product and the USB port of your PC with the cable provided.
The connection should be made after the product is turned on.

2) Following the message "Searching for a new device", the required USB driver is installed.

The installation screen may not be visible.

(!) Connecting the product to your PC while playing or while another operation is in progress may cause
the product to malfunction. Please make sure that all operations in progress are stopped before connecting.

15

4. File Management using a removable disk

-File Upload / Download

1) After connecting the player to your PC, run Windows Explorer.

2) After selecting a file or a folder to save, drag & drop the selected file or folder to the desired folder in the
removable disk drive.

[NOTE] When saving a music file in the removable disk, it is recommended to create a separate folder
shown in Windows Explorer.

[NOTE] Do not remove the USB cable while files are being moved. It may cause the product to malfunction.

16

-Format

1) It is possible to format in Windows explorer.

(!) Once formatting is done, all the data in the removable disk is deleted . Please make sure to back up all

important data before formatt ing

5. Disconnecting the product fr om a PC

1) Double-click the "Safely Remove Hardware" icon in the system tray at the lower right corner of the PC screen.

2) Select a USB device and click the <Stop> button.

When the message "S afely Remove Hardware?" is displayed, click the <OK> button and then unplug the USB cable
from the product.
[NOTE] In Windows 98 systems, the above icon is not available in the system tray.

17

6. Firmware Upgrade

● Firmware upgrade is needed to keep the product up-to-date.

1. Download the latest YUF file from our web page.

2. Connect the product to your PC.

3. Copy the downloaded YUF file to the root directory of the product.

4. After removing the product safely from your PC, turn the product on again.

5. Firmware upgrade begins to progress as the player boots.
(!) Since the player needs to be powered on for firmware upgrading, please be sure to have it fully charged before
starting the firmware upgrade.
(!!) Do not turn off the device while processing the firmware upgrade, it may cause the program error.

7. Mode Switch

Press the

<Mo de Change> button briefly to switch the mode.

(Select from MP3 or FM modes to change to.)

18

chapter 3 MP3 Mode

1. MP3 Play / Pause

Press the

<Play / Pause> button briefly to switch between Play and Pause.

2. Move to the next / Previous file

Press the

<REW / FF> button to move to the next / Previous track.

3.Rewind / Fast-forward

Press and hold the
Press and hold the

4.Repeat Mode setup

you can specify how to repeat a track. Press the
Press and hold the

<Shuffle / Auto Scan> button to listen in random.

5. LED On / Off

Press and hold the

<Mode Change> button to change the LED On / Off status.

6. EQ

<REW >button to rewind while playing. It will go to the first part of the file.
<FF>button to fast-forward while playing. It will go ahead while pressing the button.

<Shuffle / Auto Scan> bu tton briefly to listen in order.

You can select ad enjoy one of the EQ settings, such as Normal, Rock, Jazz, Classic, Pop, Live. Press the
<EQ>button to change the EQ status. Press and hold the

<EQ>button to go back to the Normal EQ.

19

7.Volume Control

Press the

<Volume + / ->button to increase/decrease continuously.

<Volume + / ->button briefly to increase/decrease the volume level. Press and hold the

20

chapter 4 FM Radio mode

1. How to scan

Press and hold the

2. How to auto-scan

Press and hold the

3. Changing channel

Press the
Press the

<REW / FF>button to set up the frequency.

<Shu ffle / Auto Scan>button to go to the next channel, while listening..

4. LED On / Off

Press and hold the

6. Volume Control

Press the

<Volume + / ->button brief increase/decrease the volume level.

Press and hold the

<REW / FF> button to scan the previous / next ch annel.

<Shuffle / Auto Scan>button to auto-scan. After scanning, it will go to the first channel.

<Mode Change> button to change the LED On / Off status.

<Volume + / > button to increase/decrease continuously.

21

chaper 5 MISCELLANEOUS

1. General Cautions

The following content is provided to protect the user's safety and prevent property damage. Please read it thoroughly for
correct use of the product.

1) Do not store the product where the temperature is too
high (over35℃) or too low (bellow-5℃).

2) Do not drop the product, subject it to impact or place it
near a magnet.

3) Avoid contact with chemicals such as benzene or thinner
as they may cause deterioration of the product.

4) Do not attempt to disassemble, repair or modify the
product.

5) Avoid dusty or dirty locations.

6) Do not make the product wet or drop in water.

7) Please exercise care when using the neck strap as the

strap can get caught in a door.

8) Falling or colliding while carrying the product In your

pocket may cause injuries such as bruising or bone fracture.

9) Do not store the product in humid places. Avoid direct

heat source such as a heater.

22

2. Earphone-related Cautions

23

3. T r oublesh ooting

Q. The product does not power on.

A. Check the Hold switch. If the Hold switch is locked, the device doesn’t get any key input. Unless the Hold switch is locked, the
battery might have been completely discharged. Connect the product to a USB port of your PC to see if the power comes on.

Q. The power goes off automatically.

A. After changing to the pause status the product will turn off automatically in 1 minute. Or if the battery is low, the device goes
power off automatically. Please check the battery.

Q. There is no sound output.

A. Check if the volume level is set to "0".

Q. There is some noise during listening to the music by earphone.
A, Check if the earphone jack has any foreign matter on it.
A. If any part of the MP3, WMA ,OGG, ASF file is damaged, it may result in sound distortion or noise. Try playing another music
file to see if this is the cause of your problem.

Q. I can't download a file.

A. Make sure that the USB cable has been properly connected.
A. Check if the OS of your PC is Windows 98. (For a Windows 98 system, you need to install a driver separately. The driver is in the
Install CD or available at www.qoolqee.com)

24

4.Product Specifications

Classification Option Specification

파일 형태

PC Interface

FM Radio

File System

Audio post
Processing

Output power

S/N ratio

Frequency

MP3

WMA

ASF

OGG

MS DRM
USB version
Supported OS

Equalizer

Music play

FM play

Music play

FM play

Music play

MPEG1,2,2.5 Layer3(8~320Kbps, VBR)
Version 9 (32~192Kbps)
OK
Ogg Vorbis (Q1–Q10)
PD-DRM 9.0
USB 2.0 (High Speed : 25 Mbps, transmission speed : 480Mbps), mass storage
Windows98SE / ME / 2000 / XP and MAC 9.2
FM Tuner(20Preset), Band selectable

FAT12, FAT16, FAT32

Normal, Rock, Jazz, Classic, Pop, Live

TBD

Over 85dB
Over 50dB

20 Hz ~ 20 KHz

range

FM play

Distortion

Battery

Earphone

76MHz ~ 108 MHz
Under 0.1 %
Li-polymer ( Under 350mAH )

3.5φ stereo, 16 Ω, 110±4dB at 1KHz