Hansgrohe HAN3909 Installation & Assembly

Page 1
EN Installation / User Instructions / Warranty FR Instructions de montage / Mode d'emploi / Garantie ES Instrucciones de montaje / Manejo / Garantía
32314xx1 32313xx1
Metris S
31446xx1 31436xx1
Talis Select
72419xx1 72415xx1
Metris S
31448xx1 31438xx1
Logis
71514xx1 71500xx1
Talis E
71748001 71747001
Metris E
31444xx1 31440xx1
Focus S
31733xx1 31732xx1
Page 2
English Français
Installation Considerations
• For best results, Hansgrohe recommends that this unit be installed by a licensed, profes­sional plumber.
• Please read over these instructions thoroughly before beginning installation. Make sure that you have all tools and supplies needed to complete the installation.
• The 4-Hole Roman Tub Set trim kits require rough 06646000 (not included). Rough 06646000 is listed by IAPMO.
• Four-hole models only: Protection against backflow is provided by a check valve in the handshower elbow and by an automatically resetting diverter.
• Models #71514xx1, #71748001, #72419001 only:
of the handshower is 2.0 GPM.
• All other four-hole models: The maximum flow rate of the handshower is 2.5 GPM.
•
The 3-Hole trim kits require rough #06607000 (not included). Rough #06607000 is listed by IAPMO.
•
This unit is not anti-scald. In Massachusetts, or if required by local plumbing code, install an approved remote pressure balance valve or other approved anti-scald device.
• Keep this booklet and the receipt (or other proof of date and place of purchase) for this product in a safe place. The receipt is required should it be necessary to request warranty parts.
The maximum flow rate
À prendre en considération pour l’installation
• Pour de meilleurs résultats, Hansgrohe recom­mande que ce produit soit installé par un plombier professionnel licencié.
• Veuillez lire attentivement ces instructions avant de procéder à l’installation. Assurez­vous de disposer de tous les outils et du matériel nécessaires pour l’installation.
• Les ensembles de robinetterie à 4 ouvertures requièrent l’utilisation de la pièce de surface 06646000 (non comprise). La pièce de surface 06646000 est homologuée par l’IAPMO.
• Pour les modèles à quatre ouver­tures seulement : La protection contre
le retour d’eau est assurée par un clapet anti-retour dans le coude de la douchette et un dispositif de dérivation à réenclenchement automatique.
• Les modèles 71514xx1, 71748001, 72419001 seulement:
douchette est de 2,0 gal/min.
• Toutes les autres modèles à quatre ouvertures:
2,5 gal/min.
• Les ensembles de robinetterie à 3 ouvertures requièrent l’utilisation de la pièce de surface 06607000 (non comprise). La pièce de surface 06607000 est homologuée par l’IAPMO.
•
Ce produit ne possède pas de dispositif anti-brûlure. Installez une vanne à pression autorégularisée externe approuvée ou tout autre dispositif anti-brûlure approuvé, tel que requis par le code de plomberie local.
Le débit de la douchette est de
Le débit de la
• Conservez ce livret et le reçu (ou une autre preuve sur laquelle figurent la date et l’endroit de l’achat) pour ce produit dans un endroit sûr. Le reçu est requis si vous commandez des pièces sous garantie.
2
Page 3
Español
Consideraciones para la instalación
• Para obtener mejores resultados, la insta­lación debe estar a cargo de un plomero profesional matriculado.
• Antes de comenzar la instalación, lea estas instrucciones detenidamente. Asegúrese de tener las herramientas y los insumos necesa­rios para completar la instalación.
• Los juegos de pieza exterior de 4 orificios requieren la pieza interior 06646000 (no incluida). La pieza interior 06646000 se encuentra en la lista de IAPMO.
• Modelos de cuatro orificios única­mente:
Una válvula antirretorno en el codo de la teleducha y un distribuidor que se reajusta automáticamente brindan protección contra el contraflujo.
• Los modelos 71514xx1, 71748001, 72419001 únicamente:
teleducha es de 2,0 galones por minuto.
• Todos los otros modelos de cuatro orificios:
2,5 galones por minuto.
El caudal de la teleducha es de
El caudal de la
Tools Required / Outiles Utiles / Herramientas Útiles
27 mm
3 mm
• Los juegos de pieza exterior de 3 orificios requieren la pieza interior 06607000 (no incluida). La pieza interior 06607000 se encuentra en la lista de IAPMO.
• Esta unidad no es anti-escaldadura. Instale una válvula remota de balance de presiones aprobada u otro dispositivo anti-escaldadura aprobado si el código de plomería local lo requiere.
• Mantenga este folleto y el recibo (u otro comprobante del lugar y fecha de compra) de este producto en lugar seguro. El recibo se requiere en caso de ser necesario solicitar piezas bajo garantía.
3
Page 4
31446xx1 31436xx1
4⅞" 4⅞" 4⅞"
5⅞"
4⅞"
8⅝"
5¾"
31438xx131448xx1
2"
32313xx132314xx1
72419001
5¾"
1⅞"
2⅜" 2¾" 2⅜"
4
1⅛"
7⅞"
8⅝"
2¼"
2¾"
72415001
3⅛"
°
2
4¼"
2"
9⅜"
2¼"
2⅜"
1⅛"
4⅞"
2¾"
1⅞"
2¾"
7⅞"
2°
4¼"
2⅜"
Page 5
6½"
9"
71748001
4⅞"
8¼"
4¼"
3"
7⅝"
5½"
8¼"
3"
8¼"
7⅝"
8¼"
7¾"
71747001
3½"
7¾"
2⅞"
5⅛"
2⅜" 2¾" 2⅜"
4⅞" 4⅞"4⅞"
2⅞"
°
30
2"
4¼"
2⅞"
2⅜"
31733xx1 31732xx1
31444xx1
2⅞"
2⅜"
1½"
2¾"
8¼"
4⅛"
2⅜"
2"
31440xx1
2⅞"
2⅜"
2⅞"
5⅛"
2¾"
2¾"
4⅞"
2⅜"
4⅛"
°
30
71514xx1 71500xx1
4⅜"
2⅞"
9⅞"
°
4 0
7⅛"
2⅞"
2⅜" 2¾" 2"
4⅞" 4⅞" 4⅞"
6¾"
9⅛"
2⅞"
2⅞"
2⅜" 2¾"
4⅜"
9⅞"
4⅞" 4⅞"
7⅛"
°
4 0
5
Page 6
Installation / Installation / Instalación
1 2
1
2
3
2
1
English Français Español
4
Turn the water off at the main before begin­ning.
Remove the plaster shields.
Lightly lubricate the threads on the handle mounting plates using white plumbers' grease.
Install the handle escutcheons.
Install the white plastic snap con­nectors and the screws.
Push the handles down firmly over the snap connectors.
6
Avant de commencer, fermez l'eau à la valve principale.
Retirez les protecteurs.
Lubrifiez légèrement les filets sur les plaques de montage en util­isant de la graisse de plomberie blanche.
Installez les écussons.
Installez les connecteurs de poignée à encliqueter.
Poussez les poignées sur les con­necteurs à encliqueter.
Cierre el paso del agua en la entrada del suministro antes de comenzar.
Retire los protectores de yeso.
Lubrique ligeramente las roscas en las placas de montaje con grasa blanca para plomería.
Instale los floróns.
Instale los conectores a presión del mando.
Presione los mandos en los conectores a presión.
Page 7
43
English Français Español
3
2
1
Inspect the alignment of the handles.
If it is not satisfactory, remove the handle, turn it slightly, and reinstall.
Vérifiez l’alignement des poignées.
Si l’alignement n’est pas satisfai­sant, retirez la poignée, tournez­la légèrement, puis réinstallez-la.
Inspeccione la alineación de los mandos.
Si la alineación no es satisfac­toria, retire el mando, gírelo levemente y reinstálelo.
7
Page 8
Nr. 10476220
Armaturenfett
Grease
3-Hole Trim Kits only / Pour les ensembles de robinetterie à 3 ouvertures seulement / Juegos de pieza exterior de 3 orificios únicamente
5 6
2
1
27 mm
English Français Español
Remove the brass plug from the tee.
Lightly lubricate the o-rings on the sealing ring using white grease (not included).
Push the spout sealing ring firmly into the spout tee.
8
Retirez le bouchon du raccord en T.
Lubrifiez les joints toriques sur la bague d’étanchéité à l’aide de graisse de plomberie blanche (non comprise).
Appuyez fermement sur la ba­gue d’étanchéité pour l’insérer dans le raccord en T.
Retire el tapón del tubo en “T”.
Lubrique los retenes anulares en el anillo de sellado con grasa blanca para plomería (no incluida).
Presione el anillo de sellado firmemente en el tubo en “T”.
Page 9
7
2
3
1
3 mm
English Français Español
Install the spout escutcheon.
Press the spout over the spout tee. Install and tighten the set screw with a 3 mm Allen wrench.
Do not overtighten the set screw or the o-rings on the sealing ring will deform, which will cause a leak.
Installez l’écusson.
Poussez le robinet sur la bague d’étanchéité.
Serrez la vis de pression à l’aide d’une clé hexagonale de 3 mm.
Ne serrez pas exces­sivement la vis de pression ou les joints toriques sur la bague d’étanchéité pour éviter de la déformer et de causer une fuite.
Instale el florón.
Presione el surtidor sobre el anillo de sellado.
Apriete el tornillo de fijación con una llave Allen de 3 mm.
No sobreapriete el tornillo de fijación, o los retenes anulares en el anillo de sellado se deformarán, lo que provocará una pérdida.
9
Page 10
4-Hole Trim Kits only / Pour les ensembles de robinetterie à 4 ouvertures
Nr. 10476220
Armaturenfett
Grease
seulement / Juegos de pieza exterior de 4 orificios únicamente
5 6
2
1
27 mm
English Français Español
Remove the brass plug from the tee.
Lightly lubricate the diverter o-rings using white grease (not included).
Press the diverter assembly firmly into the spout tee until it is fully seated.
10
Retirez le bouchon du raccord en T.
Lubrifiez les joints toriques du dispositif de dérivation à l’aide de graisse de plomberie blanche (non comprise).
Appuyez fermement sur l’assemblage du dispositif de dérivation pour l’insérer dans le raccord en T.
Retire el tapón del tubo en “T”.
Lubrique los retenes anulares del distribuidor con grasa blanca para plomería (no incluida).
Presione el conjunto del distri­buidor firmemente en el tubo en “T”.
Page 11
7 8
3
1
2
3 mm
English Français Español
Install the spout escutcheon.
Firmly press the spout over the tee and diverter. Tighten the set screw with the included 3 mm Allen wrench.
Do not overtighten the screw.
Install the pull rod.
Remove the plaster shield from the handshower holder.
Install the check valve in the elbow, with the arrow pointing in the direction of the water flow.
Installez l’écusson.
Poussez le robinet sur le disposi­tif de dérivation. Serrez la vis de pression à l’aide d’une clé hexagonale de 3 mm.
Ne serrez pas exces­sivement la vis.
Installez la tige d’entraînement.
Retirez le protecteur du support de douchette.
Installez le clapet anti-retour dans le coude de la douchette. La flèche doit pointer en direc­tion de l’écoulement d’eau.
Instale el florón.
Presione el surtidor sobre el distribuidor. Apriete el tornillo de fijación con una llave Allen de 3 mm.
No sobreapriete el tornillo de fijación.
Instale el tirador.
Retire el protector de yeso del soporte de la teleducha.
Instale la válvula antirretorno en el codo de la teleducha. La flecha debe apuntar en la direc­ción del caudal de agua.
11
Page 12
109
Nr. 10476220
Armaturenfett
Grease
4
3
1
2
2
1
English Français Español
Lightly lubricate the threads on the handle mounting plate using white plumbers' grease.
Pull out on the handshower hose.
Screw the handshower holder escutcheon into place.
Install the elbow.
Lubrifiez légèrement les filets sur le plaque de montage en util­isant de la graisse de plomberie blanche.
Tirez sur l’extrémité du tuyau pour l’éloigner du support.
Installez l’écusson.
Installez le coude.
Lubrique ligeramente las roscas en la placa de montaje con grasa blanca para plomería.
Tire el extremo de la manguera hacia afuera del soporte.
Instale el florón.
Instale el codo.
Place the screen washer in the elbow. Screw the handshower into the elbow.
Guide the handshower into the holder.
12
Installez le tamis dans le coude.
Installez la douchette.
Guidez la douchette dans le support.
Instale la arandela de filtro en el codo.
Instale la teleducha.
Guíe la teleducha en el soporte.
Page 13
Replacement Parts / Pièces détachées / Repuestos
Metris S
31446xx1 31436xx1
Metris S
31448xx1 31438xx1
96774xx0
97660000
98956xx0
13956xx0
31097xx0
97779xx0
94184000
31098xx0
96775000
31105xx0 hot/chaud/caliente 31106xx0 cold/froid/frÍo
98189000
98183000
98185000
98217000
(9x2.5)
97660000
94246000
28504xx1
31096xx0
28071xx0
94074000
97159xx0
(14x2.5)
(23x2.5)
(22x2)
31095xx0
13956xx0
31097xx0
xx = finish / couleurs / acabados
00 = chrome 82 = brushed nickel 83 = polished nickel
97779xx0
88512000
31096xx0
94184000
31098xx0
13
Page 14
Metris E
31444xx1 31440xx1
96774xx0
13956xx0
95846xx0
94184000
31098xx0
97779xx0
96775000
28504xx1
94246000
28071xx0
94074000
97159xx0
98189000
(14x2.5)
98183000
(23x2.5)
98185000
(22x2)
98217000
(9x2.5)
13956xx0
97779xx0
95846xx0
xx = finish / couleurs / acabados
00 = chrome 82 = brushed nickel 83 = polished nickel
14
88512000
94184000
31098xx0
Page 15
32314xx1 32313xx1
96774xx0
97660000
94246000
28504xx1
97779xx0
94184000
31098xx0
97660000
97779xx0
96775000
28071xx0
94074000
97159xx0
98189000
(14x2.5)
98183000
(23x2.5)
98185000
(22x2)
98217000
(9x2.5)
88512000
94184000
31098xx0
xx = finish / couleurs / acabados
00 = chrome 82 = brushed nickel 83 = polished nickel
15
Page 16
Talis E
71748001 71747001
98707000
97660000
92780000
96512000
98183000
(23x2.5)
92783000
97660000 98168000
(41x1.5)
97779000
88512000
92779000
31098000
98749000
98168000
(41x1.5)
97779000
96775000
94184000
95819000
96512000
26814401
94246000
28071000
94074000
97159000
98189000
(14x2.5)
98183000
(23x2.5)
98185000
(22x2)
98217000
(9x2.5)
92779000
16
98211000 (21x2.5)
94184000
96299000
31098000
98749000
xx = finish / couleurs / acabados
00 = chrome 82 = brushed nickel 83 = polished nickel
Page 17
Talis Select
72419001 72415001
98707000
97660000
98219000 (21x1.5)
92782000
96512000
26804401
92784000
97660000
97779000
98183000
(23x2.5)
88512000
92781000
31098000
98749000
97779000
96775000
98217000
(9x2.5)
94184000
95819000
96512000
94246000
28071000
94074000
97159000
98189000
(14x2.5)
98183000
(23x2.5)
98185000
(22x2)
92781000
98211000 (21x2.5)
94184000
96299000
31098000
98749000
xx = finish / couleurs / acabados
00 = chrome 82 = brushed nickel 83 = polished nickel
17
Page 18
Focus S
31733xx1 31732xx1
96774xx0
13956xx0
95460xx0
97660000
95459xx0
31098xx0
97660000
97779xx0
94184000
96775000
94246000
28504xx1
28071xx0
94074000
97159xx0
98189000
(14x2.5)
98183000
(23x2.5)
98185000
(22x2)
98217000
(9x2.5)
13956xx0
88512000
94184000
31098xx0
18
97779xx0
xx = finish / couleurs / acabados
00 = chrome 82 = brushed nickel 83 = polished nickel
Page 19
Logis
71514xx1 71500xx1
96774xx0
97660000
98189000
(14x2.5)
98183000
(23x2.5)
98185000
(22x2)
96775000
26811xx1
94246000
28071xx0
94074000
97159xx0
94184000
31098xx0
97660000
94184000
88512000
98217000
(9x2.5)
97779xx0
31098xx0
97779xx0
xx = finish / couleurs / acabados
00 = chrome 40 = white/chrome 82 = brushed nickel
19
Page 20
User Instructions / Instructions de service / Manejo
on ouvert abierto
off fermé cerrar
hot chaud caliente
on ouvert abierto
1
cold froid frío
2
20
Page 21
Cleaning Recommendation for Hansgrohe Products
Modern bathroom faucets, kitchen faucets and shower products are made from different materials to comply with the needs of the market with regard to design and functionality. To avoid damage to the product, it is necessary to take proper care of it.
For best results:
• Prevent the buildup of mineral scale and /or soap residue by cleaning your Hansgrohe product(s) when needed.
• Select a cleaning agent specifically intended for the type of product.
• Do not use these types of cleaners as they will cause damage to your Hansgrohe product:
Any cleaning agent containing hydrochloric acid, formic acid, lye, or acetic acid. Abrasive cleaning powders, pads, or brushes. Steam cleaners. “No rinse” cleaning agents.
• Always follow the instructions provided by the manufacturer of the cleaning agent.
• Do not mix cleaning agents, unless directed by the manufacturer.
• Do not spray cleaners directly onto the product as drops could enter openings and gaps and cause damage. When using spray cleaners, spray the cleaner onto a soft cloth or sponge.
• Always rinse your Hansgrohe product thoroughly with clear water and polish dry with a soft cloth after cleaning.
Important
• Residue from soaps, shampoos, hair dye, and other toiletries and cosmetics can cause damage. Rinse the prod­uct with clean water after each use.
• Residue from basin/tub/tile cleaner can cause damage to faucets and fittings. Immediately rinse any over­spray from the Hansgrohe product.
• Do not store any cleaning agents under your Hansgrohe product, such as in a vanity unit, as the fumes may damage the product.
• Damage to the product caused by improper care or the use of improper cleaning agents is
not covered by the warranty.
• If a component of the product is damaged, replace it, as there is risk of injury.
Conseil de nettoyage pour les produits Hansgrohe
Les robinets pour les salles de bains et les cuisines modernes ainsi que les produits récents pour les douches se com­posent de matériaux différents afin de satisfaire aux besoins du marché en termes de conception et de fonctionnalité. Afin d'éviter d'endommager le produit, il est nécessaire d'en prendre soin.
Pour de meilleurs résultats :
• Empêchez l'accumulation de tarte et/ou de résidu de savon en nettoyant votre produit Hansgrohe lorsque c'est nécessaire.
• Sélectionnez un produit de nettoyage spécifiquement prévu pour ce type de produit.
• N'utilisez pas ces types de nettoyants car ils peuvent endommager votre produit Hansgrohe :
Tout produit de nettoyage contenant de l’acide chlorhydrique, de l’acide formique, de la potasse ou de
l’acide acétique.
Les poudres de nettoyage, les tampons ou les brosses abrasives.Les nettoyeurs à vapeur.Les produits de nettoyage « sans rinçage ».
• Ne mélangez pas les produits de nettoyage, à moins que cela soit indiqué par le fabricant.
21
Page 22
• Ne pulvérisez pas les nettoyants directement sur le produit car des gouttes pourraient entrer dans les ouver­tures et les fentes et causer des dommages. Lorsque vous utilisez des nettoyants par pulvérisation, pulvérisez le nettoyant sur un chiffon ou une éponge douce.
Important
• Les residus de produits pour le corps comme les savons liquides, shampooings, gels de douche, teintures pour
cheveux, parfums, apres-rasage et vernis a ongles peuvent causer des deteriorations. Rincez le produit avec de
l'eau propre après chaque utilisation.
• Le résidu provenant des nettoyants pour cuvette/baignoire/carrelage peut endommager les robinets et les raccords de tuyauterie. Rincez immédiatement toute surpulvérisation sur le produit Hansgrohe.
• De meme, il est interdit de stocker des detergents ou des produits chimiques sous les produits, par ex. dans un
meuble sous lavabo, car les vapeurs qui s'en degagent risquent d'abimer les produits.
• Les dommages au produit causés par un mauvais entretien ou par l'utilisation de produits de nettoyage inadéquats ne sont pas couverts par la garantie.
• Si un composant du produit est endommagé, remplacez-le, car il existe un risque de blessure.
Recomendación de limpieza para los productos de Hansgrohe
Hoy en día, las griferías de baño y de cocina así como duchas modernas se componen de materiales muy distintos para satisfacer las exigencias del mercado respecto al diseño y la funcionalidad. Para evitar daños y reclamaciones hay que tener en cuenta ciertos aspectos tanto en el uso como en su limpieza.
Para obtener mejores resultados:
• Evite la acumulación de restos de jabón o sarro limpiando el producto Hansgrohe cuando sea necesario.
• Seleccione un agente de limpieza diseñado específicamente para el tipo de producto.
• No use estos tipos de limpiadores, ya que causarán daño a su producto Hansgrohe:
Agentes limpiadores que contengan ácido clorhídrico, fórmico, acético o lejía.Polvos, paños o cepillos de limpieza abrasivos. Limpiadores a vaporAgentes de limpieza "sin enjuague”.
• Siempre siga las instrucciones provistas por el fabricante del agente de limpieza.
• No mezcle los agentes de limpieza, a menos que esté indicado por el fabricante.
• No rocíe limpiadores directamente sobre el producto, ya que podrían caer gotas sobre las aberturas y espa­cios y causar daños. Cuando use limpiadores en spray, rocíe el limpiador sobre un paño suave o esponja.
• Siempre enjuague su producto Hansgrohe con agua limpia y séquelo y lústrelo con un paño suave después de la limpieza.
Importante
• Los residuos de productos de aseo como jabon liquido, champus, gel de ducha, tintes de pelo, perfumes,
lociones de afeitado y esmalte de unas pueden danar tambien los materiales. Enjuague el producto con agua
limpia después de cada uso.
• Los residuos de limpiadores para lavatorios, bañeras o azulejos pueden causar daño a los grifos y accesorios. Enjuague inmediatamente cualquier derrame que haya sobre el producto de Hansgrohe.
• Tampoco pueden generarse depositos de productos de limpieza o quimicos debajo de los productos, p. ej. En
un armario de lavabo. De lo contrario, los vapores generados pueden danar los productos.
• Los daños que resulten de un cuidado inadecuado o uso de agentes de limpieza inadecua­dos no están cubiertos por la garantía.
• Si se daña un componente del producto, reemplácelo, ya que existe riesgo de lesión.
22
Page 23
Limited Consumer Warranty
This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to Hansgrohe products that are purchased by a consumer in the United States or Canada after March 1, 1996, and installed in either in the United States or in Canada.
WHO IS COVERED BY THE WARRANTY
This warranty extends to the original purchaser only. This warranty is non-transferable.
WHAT IS COVERED BY THE WARRANTY
The warranty covers only your Hansgrohe manufactured product. Hansgrohe warrants this product against defects in material or workmanship as follows:
Hansgrohe will replace at no charge for parts only or, at its option, replace any product or part of the product that proves defective because of improper workmanship and/or material, under normal installation, use, service and maintenance. If Hansgrohe is unable to provide a replacement and repair is not practical or cannot be made in timely fashion, Hansgrohe may elect to refund the purchase price in exchange for the return of the product.
LENGTH OF WARRANTY
Replacement or repaired parts of products will be covered for the term of this warranty, as stated in the following two sentences. If you are a consumer who purchased the product for use primarily for personal, family or household purposes, this warranty extends for as long as you own the product and the home in which the product is originally installed. If you purchased the product for use primarily for any other purpose, including, without limitation, a commercial purpose, this warranty extends only (i) for 1 year, with respect to Hansgrohe & Commercial products, and (ii) for 5 years, with respect to Axor products.
THIS WARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT PAY FOR:
A. Conditions, malfunctions or damage not resulting from defects in material or workmanship. B. Conditions, malfunctions or damage resulting from normal wear and tear, improper installation, improper maintenance, misuse, abuse, negligence, accident or alteration; the use of abrasive or caustic cleaning agents or “no-rinse” cleaning products, or the use of the product in any manner contrary to the product instructions; or conditions in the home such as excessive water pressure or corrosion. C.Labor and other expenses for disconnection, deinstallation, or return of the product for warranty service (including but not limited to proper packaging and shipping costs), or for installation or reinstallation of the product. D. Accessories, connected materials and products, or related products not manufactured by Hansgrohe. E. Any Hansgrohe or Axor product sold for display purposes. F. Rubbed Bronze finish is subject to a 3-year limited warranty. Chrome and all PVD finishes are covered by the limited lifetime warranty.
G. Hansgrohe Water Filtration System is subject to a 1-year limited warranty. Warranty does not include
replacement filters.
TO OBTAIN WARRANTY PARTS OR INFORMATION
Contact your Hansgrohe retailer, or contact Technical Service at:
Hansgrohe, Inc.
1492 Bluegrass Lakes Parkway
Alpharetta, GA 30004
Toll-free 800-334-0455
In requesting warranty service, you will need to provide:
1. The sales receipt or other evidence of the date and place of purchase.
2. A description of the problem.
3. Delivery of the product or the defective part, postage prepaid and carefully packed and insured, to: Hansgrohe, Inc.
1492 Bluegrass Lakes Parkway
Alpharetta, GA 30004
Toll-free 800-334-0455
When warranty service is completed, any repaired or replacement product or part will be returned to you postage prepaid.
23
Page 24
EXCLUSIONS AND LIMITATIONS
REPAIR OR REPLACEMENT (OR, IN LIMITED CIRCUMSTANCES, REFUND OF THE PURCHASE PRICE) AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. HANSGROHE NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO CREATE FOR IT ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH THIS PRODUCT. HANSGROHE SHALL NOT BE LIABLE TO PURCHASER OR ANY OTHER PERSON FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, ARISING OUT OF BREACH OF THIS WARRANTY OR ANY IMPLIED WARRANTY (INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY).
Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
TO THE EXTENT PERMITTED BY LAW, ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THE EXPRESS WARRANTY.
Some states do not allow limitations on how long an implied warranty may last, so the above limitations may not apply to you. You may be required by law to give us a reasonable opportunity to correct or cure any failure to comply before you can bring any action in court against us under the Magnuson-Moss Warranty Act.
PRODUCT INSTRUCTIONS AND QUESTIONS
Upon purchase or prior to installation, please carefully inspect your Hansgrohe product for any damage or visible defect. Prior to installing, always carefully study the enclosed instructions on the proper installation and the care and maintenance of this product. If you have questions at any time about the use, installation or performance of your Hansgrohe product, or this warranty, please write us or call us toll-free at 800-334-0455.
24
Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004
Tel. 770-360-9880 • Fax 770-889-1783
www.hansgrohe-usa.com
US - Installation Instructions • Part No. 90597504 • Revised 04/2016
Loading...