1. Please contact Hannstar Display Corp. before designing your product based on this module specification.
2.The information contained herein is presented merely to indicate the characteristics and performance of
www.jxlcd.com
www.jxlcd.com
相關文件:
DC130-004167
Accepted by:
Signature Date
Proposed by: Technical Service Division
Signature Date
our products. No responsibility is assumed by Hannstar for any intellectual property claims or other
problems that may result from application based on the module described herein.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
HannStar Display Corp.
Document Title
Document No. DC130-004166 Revision 1.0
Rev. Updated No. Date Description of change
HSD220MKW1 Specification for 深耕
Record of Revisions
Page No. 2 / 26
1.0
A01 Jun.,19,2009
www.jxlcd.com
www.jxlcd.com
HSD220MKW1-A01
released.
Product Specification was first
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
HannStar Display Corp.
Document Title
Document No. DC130-004166 Revision 1.0
1.0 GENERAL DESCRIPTIONS
1.1 Introduction
HannStar Display model HSD220MKW1-A01 is a color active matrix thin film transistor
(TFT) liquid crystal display (LCD) that uses amorphous silicon TFT as a switching device.
This model is composed of a TFT LCD panel, the voltage reference, common voltage,
DC-DC converter, column, and row driver circuit. This TFT LCD has a 22-inch diagonally
measured active display area with WSXGA+ resolution (1050 vertical by 1680 horizontal
pixel array).
Display area 473.76 (H) x296.16 (V) mm
Number of Pixel 1680(H) x 1050(V) Pixels
HSD220MKW1 Specification for 深耕
Item Specification Unit
Page No. 4 / 26
Pixel pitch 0.282(H) x 0.282(V) mm
Pixel arrangement RGB Vertical stripe
Display color 16.7M (6-bit+HiFRC)
Display mode Normally white
Surface treatment Antiglare (3H)
Weight 3050 G
Back-light 4-CCFLs, Top & bottom edge side
Input signal 2-ch LVDS
Power consumption
1.4 Applications
■ Desktop and Multi-function monitors
■ Display terminals for AV applications
■ Monitors for industrial applications
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
Logic system 4.2 @ v-color pattern W
B/L system 5.48 W
HannStar Display Corp.
Document Title
Document No. DC130-004166 Revision 1.0
HSD220MKW1 Specification for 深耕
Page No. 5 / 26
1.5 Mechanical Information
Item Min. Typ. Max. Unit
Horizontal(H) 493.2 493.7 494.2 mm
Module Size
Vertical(V) 319.6 320.1 320.6 mm
Depth(D) 16.0 16.5 17.0 mm
Weight (without inverter) 2850 3050 3250 g
Torque of customer screw hole 3.0 Kgf*Cm
2.0 ABSOLUTE MAXIMUM RATINGS
2.1 Absolute Rating of Environment
Item Symbol Min. Max. Unit Note
Storage temperature T
Operating temperature T
Vibration (non-operating) V
Shock (non-operating) S
Storage humidity H
Operating humidity HOP 10 80 %RH (4)
www.jxlcd.com
Low pressure (operating) P
www.jxlcd.com
Low pressure (non-operating) P
Note (1) Storage /Operating temperature
Storage Range
-40 -20
STG
OPR
NOP
NOP
STG
LOP
LNOP
Humidity (%)
100
90
80
60
40
20
10
0
0
Temperature (
-20 60 oC
0 50 oC (1)
-- 1.5 G (2)
-- 70 G (3)
10 90 %RH (3)
697 -- HPa (5)
116 -- HPa (6)
Operating Range
20
o
C)
50
60 40
65
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
HannStar Display Corp.
Document Title
Document No. DC130-004166 Revision 1.0
(2) 10-500Hz sine wave, X, Y, Z each directions, 30min/cycle.
(3) 11ms, ±X, ±Y, ±Z direction, one time each. For this shock test,
It is necessary to fill the silicon rubber between the shock jigs as buffer.
(4) Max wet bulb temp. =39
(5) 2 hrs. (10000 feet)
(6) 24hrs. (50000 feet)
2.2 Electrical Absolute Rating:
2.2.1 TFT LCD Module:
Item Symbol Min. Max. Unit. Note
HSD220MKW1 Specification for 深耕
o
C
Page No. 6 / 26
Power supply Voltage VDD -0.3 6.0
2.2.2 Back Light Unit:
Item Symbol Min. Max. Unit Note
Lamp current IL 3.0 9.0 mA (1)(2)(3)
Lamp frequency fL 40 80 KHz (1)(2)(3)
Note: (1) Permanent damage may occur to the LCD module if beyond this specification.
(2) To exceed 7.5mA, life time accelerate drop down and if to exceed 9.0 mA has safety
(3) Within Ta=25±2°C
www.jxlcd.com
www.jxlcd.com
Functional operation should be restricted to the conditions described under Normal
Operating Conditions.
problem. If current lower than 3.5 mA, CCFL would be unstable or damaged.
V(DC)
(1)(2)
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
HannStar Display Corp.
Document Title
Document No. DC130-004166 Revision 1.0
HSD220MKW1 Specification for 深耕
Page No. 7 / 26
3.0 OPTICAL CHARACTERISTICS
3.1 Optical specification
Item Symbol ConditionMin. Typ. Max. Unit Note
Contrast CR 700 1000 -- (1)(2)
Response time
Rising TR -- 1.5 3
Falling TF -- 3.5 7
msec(1)(3)
White luminance
(center of screen)
Red
Gree
Color
n
chromaticity
(CIE1931)
Blue
White
Hor.
Viewing angle
www.jxlcd.com
www.jxlcd.com
Ver.
Hor.
Viewing angle
Ver.
Brightness uniformity B
240 300 cd/m
Y
L
Rx
Ry
Gx
Gy
Bx
By
Wx
Wy
Θ
80 85 --
L
80 85 --
Θ
R
Θ
75 80 --
H
Θ
L
Θ
80 85 --
L
80 85 --
Θ
R
Θ
80 85 --
H
Θ
L
UNI
o
Θ=0
o
φ=0
Normal
viewing
angle
CR>10
CR>5
o
Θ=0
o
φ=0
0.615 0.645 0.675
0.310 0.340 0.370
0.270 0.300 0.330
0.600 0.630 0.660
0.110 0.140 0.170
0.035 0.065 0.095
0.280 0.310 0.340
0.300 0.330 0.360
75 80 --
80 85 -75 -- -- % (6)
(1)(4)(7)
2
(IL=7.5mA)
(1)(5)
3.2 Measuring Condition
■ Measuring surrounding: dark room
■ Lamp current I
■ V
=5.0V, fV=60Hz, f
DD1
■ Surrounding temperature: 25±2
■ 30min. Warm-up time.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
■ FPM520 of Westar Display technologics, INC., which utilized SR-3 for Chromaticity and
BM-5A for other optical characteristics.
■ Measuring spot size: 20~21mm
Note (1) Definition of Viewing Angle:
Note (2) Definition of Contrast Ratio (CR):
measured at the center point of panel
Luminance with all pixels white (L255)
CR =
Luminance with all pixels black (L0)
www.jxlcd.com
www.jxlcd.com
HSD220MKW1 Specification for 深耕
Θ
L
Θ
=90o
L
Φ
L
6’ o’clock
=90
L
o
Φ
Φ
H
12’ o’clock
H
R
=90
o
Φ
Θ
Page No. 8 / 26
Θ
=90o
R
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
HannStar Display Corp.
Document Title
Document No. DC130-004166 Revision 1.0
Note (3) Definition of Response Time: Sum of T
Note (4) Optical characteristic measurement setup
Optical
response
LCD Panel
www.jxlcd.com
www.jxlcd.com
HSD220MKW1 Specification for 深耕
and TF
R
white(TFT OFF)black(TFT ON)white(TFT OFF)
T
R
100%
90%
10%
0%
Field = 1
120cm
o
Page No. 9 / 26
T
F
Photo-detector (BM-5A)
time
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
HannStar Display Corp.
Document Title
Document No. DC130-004166 Revision 1.0
Note (5) Definition of Center Luminance of White
Center Luminance= Y1
HSD220MKW1 Specification for 深耕
Page No. 10 / 26
1/10V
1/10 H
1/2H
1/10H
Y1
1/2V
1/10V
www.jxlcd.com
www.jxlcd.com
Note (6) Definition of brightness uniformity
(Min Luminance of 9 points)
Luminance uniformity = x 100%
(Max Luminance of 9 points)
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
HannStar Display Corp.
Document Title
Document No. DC130-004166 Revision 1.0
4.0 BLOCK DIAGRAM
4.1 LCD Module Block Diagram:
Connector CN1
www.jxlcd.com
www.jxlcd.com
DC/DC
Converter
HSD220MKW1 Specification for 深耕
TCON with
LVDS receiver
Y-driver IC
Gamma
Reference
Voltage
Generator
Page No. 11 / 26
X-driver IC
Liquid Crystal Panel
1680×1050 pixels
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
HannStar Display Corp.
Document Title
Document No. DC130-004166 Revision 1.0
HSD220MKW1 Specification for 深耕
Page No. 12 / 26
4.2 Back Light Unit
1 Hot 1
2 Cold 1
1 Hot 2
2 Cold 2
Back light l
CN2, 3, 4, 5.
1 Hot 1
2 Cold 1
1 Hot 2
2 Cold 2
4.3 Pixel Format
www.jxlcd.com
www.jxlcd.com
1,1
(odd)
1,2
(even)
1,3
(odd)
1,4
(even)
1680
1,
2,1
(odd)
LCD Display Area
amp
1 Pixel
R
G
R
B
1050 Lines
R
1050
,1
1050
6801
1680 Pixels
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
HannStar Display Corp.
Document Title
Document No. DC130-004166 Revision 1.0
HSD220MKW1 Specification for 深耕
Page No. 13 / 26
4.4 Relationship Between Displayed Color and Input
MSB LSB MSB LSB MSB LSB Gray scale
Display
Black L L L L L L L L L L L L L L L L L L L L L L L L -
Blue L L L L L L L L L L L L L L L L H H H H H H H H -
Green L L L L L L L L H H H H H H H H L L L L L L L L Basic
color
Gray scale
of Red
Gray scale
of Green
Gray scale
of Blue
Gray scale
of White &
Black
Light Blue L L L L L L L L H H H H H H H H H H H H H H H H -
Red H H H H H H H H L L L L L L L L L L L L L L L L Purple H H H H H H H H L L L L L L L L H H H H H H H H Yellow HH H H H H HHHHHHHHHHLLLLLL L L -
White H H H H H H H H H H H H H H H H H H H H H H H H Black L L L L L L L L L L L L L L L L L L L L L L L L L0
Dark L L L L L L H L L L L L L L L L L L L L L L L L L2
Light H H H H H H L H L L L L L L L L L L L L L L L L L255
Red H H H H H H H H L L L L L L L L L L L L L L L L Red L255
Black L L L L L L L L L L L L L L L L L L L L L L L L L0
Dark L L L L L L L L L L L L L L H L L L L L L L L L L2
www.jxlcd.com
www.jxlcd.com
Light L L L L L L L L H H H H H H L H L L L L L L L L L255
Green L L L L L L L L H H H H H H H H L L L L L L L L Green L255
Black L L L L L L L L L L L L L L L L L L L L L L L L L0
Dark L L L L L L L L L L L L L L L L L L L L L L H L L2
Light L L L L L L L L L L L L L L L L H H H H H H L H L255
Blue L L L L L L L L L L L L L L L L H H H H H H H H Blue L255
Black L L L L L L L L L L L L L L L L L L L L L L L L L0
Dark L L L L L L H L L L L L L L H L L L L L L L H L L2
Light H H H H H H L H H H H H H H L H H H H H H H L H L253
White H H H H H H H H H H H H H H H H H H H H H H H H White L255
L L L L L L L H L L L L L L L L L L L L L L L L L1
↑ ︰ ︰ ︰ L3…L251
↓
H H H H H H L L L L L L L L L L L L L L L L L L L255
H H H H H H H L L L L L L L L L L L L L L L L L L255
L L L L L L L L L L L L L L L H L L L L L L L L L1
↑ ︰ ︰ ︰ L3…L251
↓
L L L L L L L L H H H H H H L L L L L L L L L L L255
L L L L L L L L H H H H H H H L L L L L L L L L L255
L L L L L L L L L L L L L L L L L L L L L L L H L1
↑ ︰ ︰ ︰ L3…L251
↓
L L L L L L L L L L L L L L L L H H H H H H L L L255
L L L L L L L L L L L L L L L L H H H H H H H L L255
L L L L L L L H L L L L L L L H L L L L L L L H L1
↑ ︰ ︰ ︰ L3…L251
↓
H H H H H H L L H H H H H H L L H H H H H H L L L252
H H H H H H H L H H H H H H H L H H H H H H H L L254
Level
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
HannStar Display Corp.
Document Title
Document No. DC130-004166 Revision 1.0
5.0 I/O CONNECTION PIN ASSIGNMENT
5.1 Interface Connector (30-pins ) (HRS: MDF76GW-30S-1H or equivalent)
Pin No. Signal Description
www.jxlcd.com
www.jxlcd.com
5.2 Back Light Unit (CCFL) Connectors:
CN2, 3, 4, 5: CCFL Power Source (Yeonho 35001H5-02 or equivalent)
HSD220MKW1 Specification for 深耕
1 RinO0- Receiver Signal (-)
2 RinO0+ Receiver Signal (+)
3 RinO1- Receiver Signal (-)
4 RinO1+ Receiver Signal (+)
5 RinO2- Receiver Signal (-)
6 RinO2+ Receiver Signal (+)
7 VSS Ground
8 RinOC- Clock Signal (-)
9 RinOC+ Clock Signal (+)
10 RinO3- Receiver Signal (-)
11 RinO3+ Receiver Signal (+)
12 RinE0- Receiver Signal (-)
13 RinE0+ Receiver Signal (+)
14 VSS Receiver Signal (+)
15 RinE1- Receiver Signal (-)
16 RinE1+ Receiver Signal (+)
17 VSS Ground
18 RinE2- Receiver Signal (-)
19 RinE2+ Receiver Signal (+)
20 RinEC- Clock Signal (-)
21 RinEC+ Clock Signal (+)
22 RinE3- Receiver Signal (-)
23 RinE3+ Receiver Signal (+)
24 VSS Ground
25 NC NC
26 NC GND
27 NC GND
28 VDD+5V Power Supply, 5V (Typical)
29 VDD+5V Power Supply, 5V (Typical)
30 VDD+5V Power Supply, 5V (Typical)
Page No. 14 / 26
Pin No. Symbol Color Function
1 Hot1 Pink CCFL power supply (High voltage)
2 Cold1 White Ground
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
HannStar Display Corp.
Document Title
Document No. DC130-004166 Revision 1.0
HSD220MKW1 Specification for 深耕
Page No. 15 / 26
6.0 ELECTRICAL CHARACTERISTICS
6.1 TFT LCD Module:
Item SymbolMin. Typ. Max. Unit Note
Voltage of power supply VDD 4.5 5.0 5.5 V
I
595 695 795 (1)
DD0
Current of power supply
Vsync frequency fV 56 60 75 Hz (2)
Hsync frequency fH 60.5 64.8 82.4 KHz
Frequency f
Input rush current I
I
720 870 1020 mA (1)
DD1
960 1160 1360 mA (1)
I
DD2
55.64 59.61 82 MHz
DCLK
--- --- 2 A (3)
RUSH
Note (1)
(a) White: I
(b) V- Color: I
www.jxlcd.com
www.jxlcd.com
DD0
DD1
White
Yellow
Purple
Red
Cyan
Green
Blue
Black
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
HannStar Display Corp.
Document Title
Document No. DC130-004166 Revision 1.0
HSD220MKW1 Specification for 深耕
Page No. 16 / 26
(c) Mosaic: I
L0
Grey scale: L0~L255
L255: Luminance with all pixels white.
www.jxlcd.com
www.jxlcd.com
L0: Luminance with all pixels black.
DD2
L31
Note (2) When fv is too low, a flicker may be occurred on the display.
Note (3) Input Rush Current condition
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
GND
0.1VDD
0.9VDD
5 V
700us~10ms
HannStar Display Corp.
Document Title
Document No. DC130-004166 Revision 1.0
6.2 Back-Light Unit
The back- light system is an direct-lighting type with 4CCFLs
The characteristics of the lamp are shown in the following tables.
Item SymbolMin. Typ. Max. Unit Note
Lamp current IL 3.0 7.5 9.0 mA(rms) (1)
Lamp voltage VL - 730 - V(rms) IL=7.5mA
Frequency fL 40 50 80 KHz (2)
Operating Lifetime Hr 40,000-- -- Hour 7.5mA(3)
Startup voltage Vs
LCD MODULE
www.jxlcd.com
www.jxlcd.com
Note (1)
Lamp current is measured with current meter for high frequency as shown below. Specified
values are for a single lamp. To exceed 7.5 mA, life time accelerate drop down and if to
exceed 9.0 mA has safety problem. If current lower than 3.5 mA, CCFL would be unstable or
damaged.
Note (2)
Lamp frequency may produce interference with horizontal synchronous frequency and this
may cause ripple noise on the display. Therefore lamp frequency shall be kept away from the
horizontal synchronous frequency and its harmonics as far as possible in order to avoid
interference.
Note (3)
Lamp life time (Hr) can be defined as the time in which it continues to operate under the
condition : Ta=25±3
brightness becomes less than 50%
HSD220MKW1 Specification for 深耕
1650 at 25oC
1850
1
1
2
2
1
1
2
2
1
1
2
2
1
1
2
2
o
C, Typical IL value indicated in the above table and fL=48 kHz until the
-- -- V(rms)
Page No. 17 / 26
(Cold Cathode Fluorescent Lamp).
o
C
at 0
A
INVERTER
TDK TBD332LR
A
A
A
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
HannStar Display Corp.
Document Title
Document No. DC130-004166 Revision 1.0
Note (4)
CCFL inverter should be able to provide a voltage over specified value (Vs) in the above table.
Lamp units need at least Vs value shown above to ignition.
Note (5)
The voltage over specified value (Vs) should be applied to the lamp more than 1 second after
startup. Otherwise, the lamp may not be turned on. The used lamp current is the lamp typical
current.
Note (6)
The output voltage waveform and current waveform of the inverter must be symmetrical
(Unsymmetrical ratio is less than 10%). Please do not use the inverter which has
unsymmetrical voltage and current waveform, and spike waveform. The inverter design which
can provide the best optical performance, power efficiency, and lamp life should under the
following conditions.
a. The asymmetry rate of the inverter waveform should be less than 10%.
b. The distortion tae of the waveform should be within √2±10%.
c. The inverter output waveform should be better similar to the ideal sine wave.
www.jxlcd.com
www.jxlcd.com
Asymmetry rate = |I
Distortion rate = I
HSD220MKW1 Specification for 深耕
Ip
I-p
p-I-p| / Irms x100%
p (or I-p) / Irms
Page No. 18 / 26
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
HannStar Display Corp.
(2)
Document Title
Document No. DC130-004166 Revision 1.0
HSD220MKW1 Specification for 深耕
Page No. 19 / 26
6.3 Interface Timing ( DE mode)
Item Symbol Min. Typ. Max. Unit
Frame Rate -- 60 60 - Hz
Frame Period t1 - 1080 1099 line
Vertical Display Time t2 - 1050 - line
Vertical Blanking Time t3 - 30 49 line
1 Line Scanning Time t4 - 920 1136 clock
Horizontal Display Time t5 - 840 - clock
Horizontal Blanking Time t6 - 80 296 clock
Clock Rate t7 59.61 59.61 82 MHz
Timing Diagram of Interface Signal (DE mode)
(1)Vertical
NCLK
DE
0~5
R
0~5
G
0~5
B
Horizontal
NCLK
DE
0~5
R
0~5
G
0~5
B
t2
t4
www.jxlcd.com
X,1X,2X,3X,Y
www.jxlcd.com
t7
1234567891011
t1
X,1048X,1050
X,1049
t4
t5t6
1671
1673
1675
1677
12
1672
1674
1676
1678
1679
1680
t3
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
HannStar Display Corp.
Document Title
Document No. DC130-004166 Revision 1.0
HSD220MKW1 Specification for 深耕
Page No. 20 / 26
6.4 Power On / Off Sequence:
Power On
Power Off
Power Supply
0.9VDD 0.9V
DD
0V
0.1V
0.1V
DD
TP1
DD
0.1VDD
TP2
Signal
0.6V 0.6V
0V
TP3
TP4
Backlight
(Recommended)
TP5
50%
TP6
50%
Note:(1) The supply voltage of the external system for the module input should be the same as the
(2) Apply the lamp volatge within the LCD operation range. When the back-light turns on
before the LCD operation or the LCD truns off before the back-light turns off, the display
may momentarily become white.
(3) In case of VDD = off level, please keep the level of input signal on the low or keep a high
impedance.
(4) TP4 should be measured after the module has been fully discharged between power off
and on period.
(5) Interface signal shall not be kept at high impedance when the power is on.
DD
.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
HannStar Display Corp.
Q
|
|
寬橫向
Document Title
Document No. DC130-004166 Revision 1.0
HSD220MKW1 Specification for 深耕
Page No. 21 / 26
7.0 OUTLINE DIMENSION
7.1 Front View:
www.jxlcd.com
www.jxlcd.com
<P> BM
> BM
<
寬縱向
| A-A’ |
B-B’
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
HannStar Display Corp.
Document Title
Document No. DC130-004166 Revision 1.0
7.2 Back View:
HSD220MKW1 Specification for 深耕
Page No. 22 / 26
www.jxlcd.com
www.jxlcd.com
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
HannStar Display Corp.
Document Title
Document No. DC130-004166 Revision 1.0
HSD220MKW1 Specification for 深耕
Page No. 23 / 26
8.0 LOT MARK
8.1 Lot Mark
1 2 3 4 56789
code 1,2,3,4,5,6: HannStar internal flow control code.
code 7: production location.
code 8: production year.
code 9: production month.
code 10,11,12,13,14,15: serial number.
Note (1) Production Year
Year 2001 2002 20032004200520062007 2008 20092010
Mark 1 2 3 4 5 6 7 8 9 0
Note (2) Production Month
Month Jan.Feb. Mar.Apr.May.Jun.Jul.Aug.Sep. Oct Nov. Dec.
Mark 1 2 3 4 5 6 7 8 9 A B C
8.2 Location of Lot Mark
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
www.jxlcd.com
www.jxlcd.com
(1) The label is attached to the backside of the LCD module.
(2) This is subject to change without prior notice.
HSD220MKW1
Hannstar D
isplay Corporation
MAD
E IN TAIWAN
-A01
Rev:
RoHS
Lot mark
101112 13 14 15
HannStar Display Corp.
Document Title
Document No. DC130-004166 Revision 1.0
9.0 PACKAGE SPECIFICATION
9.1 Packing form
(1) Package quantity in one carton: 6 pieces
HSD220MKW1 Specification for 深耕
Page No. 24 / 26
(2) Carton size: 600 x 267 x 440
9.2 Packing assembly drawings
www.jxlcd.com
www.jxlcd.com
(mm)
H
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
HannStar Display Corp.
Document Title
Document No. DC130-004166 Revision 1.0
HSD220MKW1 Specification for 深耕
Page No. 25 / 26
10.0 GENERAL PRECAUTION
10.1 Use Restriction
This product is not authorized for use in life supporting systems, aircraft navigation control
systems, military systems and any other application where performance failure could be
life-threatening or otherwise catastrophic.
10.2 Disassembling or Modification
Do not disassemble or modify the module. It may damage sensitive parts inside LCD
module, and may cause scratches or dust on the display. HannStar does not warrant the
module, if customers disassemble or modify the module.
10.3 Breakage of LCD Panel
10.3.1 If LCD panel is broken and liquid crystal spills out, do not ingest or inhale liquid
crystal, and do not contact liquid crystal with skin.
10.3.2 If liquid crystal contacts mouth or eyes, rinse out with water immediately.
10.3.3 If liquid crystal contacts skin or cloths, wash it off immediately with alcohol and
rinse thoroughly with water.
10.3.4 Handle carefully with chips of glass that may cause injury, when the glass is
broken.
10.4 Electric Shock
10.4.1 Disconnect power supply before handling LCD module.
10.4.2 Do not pull or fold the CCFL cable.
10.5 Absolute Maximum Ratings and Power Protection Circuit
www.jxlcd.com
www.jxlcd.com
10.4.3 Do not touch the parts inside LCD modules and the fluorescent lamp’s connector
or cables in order to prevent electric shock.
10.5.1 Do not exceed the absolute maximum rating values, such as the supply voltage
variation, input voltage variation, variation in parts’ parameters, environmental
temperature, etc., otherwise LCD module may be damaged.
10.5.2 Please do not leave LCD module in the environment of high humidity and high
temperature for a long time.
10.5.3 It’s recommended employing protection circuit for power supply.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
HannStar Display Corp.
Document Title
Document No. DC130-004166 Revision 1.0
10.6 Operation
10.6.1 Do not touch, push or rub the polarizer with anything harder than HB pencil lead.
Use fingerstalls of soft gloves in order to keep clean display quality, when
Persons handle the LCD module for incoming inspection or assembly.
10.6.2 When the surface is dusty, please wipe gently with absorbent cotton or other soft
10.6.3 Wipe off saliva or water drops as soon as possible. If saliva or water drops contact
with polarizer for a long time, they may causes deformation or color fading.
10.6.4 When cleaning the adhesives, please use absorbent cotton wetted with a little
petroleum benzine or other adequate solvent.
10.7 Mechanism
Please mount LCD module by using mounting holes arranged in four corners tightly.
10.8 Static Electricity
10.8.1 Protection film must remove very slowly from the surface of LCD module to
prevent from electrostatic occurrence.
10.8.2 Because LCD module uses CMOS-IC on circuit board and TFT-LCD panel, it is
very weak to electrostatic discharge. Please be careful with electrostatic
discharge.
10.8.3 Persons who handle the module should be grounded through adequate methods.
10.9 Strong Light Exposure
10.10 Disposal
www.jxlcd.com
www.jxlcd.com
The module shall not be exposed under strong light such as direct sunlight. Otherwise,
display characteristics may be changed.
When disposing LCD module, obey the local environmental regulations.
HSD220MKW1 Specification for 深耕
material.
Page No. 26 / 26
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.