Document TitleHSD190MGW1 Specification for Roadwell Page No. 1/ 28
Document No.DC130-003910 Revision 1.0
TO ΚRoad Well
DateΚ2009/03/17
Customer Acceptance Specification
www.panelook.com
Model : HSD190MGW1
-A04
ઌᣂ֮ٙ: IIS DC130-003911 / IIS DC130-003912
Accepted by:
Signature Date
Proposed by: Technical Service Division
Signature Date
Note:1. Please contact HannStar Display Corp. before designing your product based on
this module specification.
2.The information contained herein is presented merely to indicate the characteristics and
performance of our products. No responsibility is assumed by HannStar for any
intellectual property claims or other problems that may result from application based on
the module described herein.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Document TitleHSD190MGW1 Specification for Roadwell Page No. 2/ 28
Document No.DC130-003910 Revision 1.0
Rev.Date Sub-ModelDescription of change
1.0 Mar.,17, 2009A04 Preliminary Product Specification was first issued.
www.panelook.com
Record of Revisions
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Document TitleHSD190MGW1 Specification for Roadwell Page No. 3/ 28
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Document TitleHSD190MGW1 Specification for Roadwell Page No. 4/ 28
Document No.DC130-003910 Revision 1.0
1.0 GENERAL DESCRIPTIONS
1.1 Introduction
HannStar Display model HSD190MGW1-A04 is a color active matrix thin film transistor
(TFT) liquid crystal display (LCD) that uses amorphous silicon TFT as a switching device.
This model is composed of a TFT LCD panel, the voltage reference, common voltage,
DC-DC converter, column, and row driver circuit. This TFT LCD has a 19-inch diagonally
measured active display area with WXGA+ resolution (900 vertical by 1440 horizontal
pixel array).
1.2 Features
Ŷ 19” WXGA+ TN(Twisted Nematic) mode TFT LCD panel
Ŷ High speed response time
Ŷ 4 CCFLs Backlight system
Ŷ Supported WXGA+ (V:900 lines, H:1440 pixels) resolution
Ŷ Supported to 75Hz refresh rate
Ŷ LCD Timing Controller
Ŷ RoHS compliance
www.panelook.com
1.3 General information
Item Specification Unit
Outline dimension 42827818.5 (typ.) mm
Display area 408.24 (H) x255.15 (V) mm
Number of Pixel 1440(H) x 900(V) Pixels
Pixel pitch 0.2835(H) x 0.2835(V) mm
Pixel arrangement RGB Vertical stripe
Display color 16.2M (6-bit+FRC)
Display mode Normally white
Surface treatment Antiglare, Hard-Coating (3H)
Weight 2500 G
Back-light 4-CCFLs, Top & bottom edge side
Input signal 2-ch LVDS
Logic system 3.75
W
Power consumption
B/L system 22
W
Optimum viewing direction 6 o’clock
1.4 Applications
Ŷ Desktop and Multi-function monitors
Ŷ Display terminals for AV applications
Ŷ Monitors for industrial applications
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Document TitleHSD190MGW1 Specification for Roadwell Page No. 5/ 28
Document No.DC130-003910 Revision 1.0
1.5 Mechanical Information
Item Min. Typ. Max. Unit
www.panelook.com
Horizontal(H) 427.5 428.0 428.5 mm
Module Size
Vertical(V) 277.5 278.0 278.5 mm
Depth(D) 18.0 18.5 19.0 mm
Weight (without inverter) 2300 2500 2700 g
Torque of customer screw hole -- -- 3.0 Kgf*Cm
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Document TitleHSD190MGW1 Specification for Roadwell Page No. 6/ 28
Document No.DC130-003910 Revision 1.0
2.0 ABSOLUTE MAXIMUM RATINGS
2.1 Absolute Rating of Environment
Item Symbol Min. Max. Unit Note
Storage temperature T
Operating temperature T
Vibration(non-operating) V
Shock(non-operating) S
Storage humidity H
Operating humidity HOP 10 80 %RH (4)
Low pressure(operating) P
Low pressure(non-operating) P
Note (1)Storage /Operating temperature
www.panelook.com
-20 60 oC
STG
0 50 oC (1)
OPR
-- 1.5 G (2)
NOP
-- 50 G (3)
NOP
10 90 %RH (3)
STG
697 -- HPa (5)
LOP
116 -- HPa (6)
LNOP
Humidity (%)
100
90
Storage Range
-20-40
80
60
40
20
10
0
Operating Range
0
Temperature (
204060
o
C)
50
65
(2) 10-300Hz sine wave, X,Y,Z each directions, 10min/cycle.
(3) 11ms, ±X, ±Y, ±Z direction, one time each. For this shock test,
It is necessary to fill the silicon rubber between the shock jigs as buffer.
(4) Max wet bulb temp. =39
o
C
(5) 2 hrs. (10000 feet)
(6) 24hrs. (50000 feet)
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Document TitleHSD190MGW1 Specification for Roadwell Page No. 7/ 28
Document No.DC130-003910 Revision 1.0
2.2 Electrical Absolute Rating:
2.2.1 TFT LCD Module:
Item Symbol Min. Max.Unit.Note
www.panelook.com
Power supply VoltageVDD
-0.3 6.0 V(DC)(1)(2)
2.2.2 Back Light Unit:
Item Symbol Min. Max. Unit Note
Lamp current IL 3.0 9.0 MA (1)(2)(3)
Lamp frequency fL 45 80 KHz (1)(2)(3)
Note: (1) Permanent damage may occur to the LCD module if beyond this specification.
Functional operation should be restricted to the conditions described under
Normal Operating Conditions.
(2) To exceed 6.5mA, life time accelerate drop down and if to exceed 9.0mA has
safety problem. If current lower than 3.5 mA, CCFL would be unstable or
damaged.
(3) Within Ta=25±2°C
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Document TitleHSD190MGW1 Specification for Roadwell Page No. 8/ 28
Document No.DC130-003910 Revision 1.0
3.0 OPTICAL CHARACTERISTICS
3.1 Optical specification
Item Symbol ConditionMin. Typ. Max.UnitNote
Contrast CR 450 700 -- (1)(2)
RisingTR -- 1.5 3
Response time
FallingTF -- 3.5 7
www.panelook.com
msec(1)(3)
White luminance
(center of screen)
Red
Color
Green
chromaticity
(CIE1931)
Blue
White
Hor.
Viewing angle
Ver.
Hor.
Viewing angle
Ver.
Brightness uniformity B
Y
L
Rx
Ry
Gx
Gy
Bx
By
Wx
Wy
ӘӘ
R
Ә
H
Ә
L
Ә
L
Ә
R
Ә
H
Ә
L
UNI
L
o
Ә
=0
o
φ=0
Normal
viewing
angle
CR>10
CR>5
o
Ә
=0
o
φ=0
(1)(4)(7)
240 300 -- cd/m
0.650
0.325
0.300
-0.03
0.615
0.145
0.080
0.310
0.330
+0.03
2
(IL=6.5mA)
(1)(5)
65 75 --
65 75 --
65 75 --
55 65 --
75 85 --
75 85 --
75 85 --
65 75 --
75 -- -- % (6)
3.2 Measuring Condition
Ŷ Measuring surrounding: dark room
Ŷ Lamp current I
Ŷ V
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Document TitleHSD190MGW1 Specification for Roadwell Page No. 9/ 28
Document No.DC130-003910 Revision 1.0
3.3 Measuring Equipment
Ŷ FPM520 of Westar Display technologics, INC., which utilized SR-3 for Chromaticity and
BM-5A for other optical characteristics.
Ŷ
Measuring spot size : 20~21mm
Note (1) Definition of Viewing Angle:
www.panelook.com
ӥ
H
12’ o’clock
ӥ
=90
H
o
Ә
ӘL=90
L
o
ӥ
L
Ә
R
6’ o’clock
=90
L
o
ӥ
Note (2) Definition of Contrast Ratio(CR) :
measured at the center point of panel
Luminance with all pixels white (L255)
CR =
Luminance with all pixels black (L0)
ӘR=90
o
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Document TitleHSD190MGW1 Specification for Roadwell Page No. 10/ 28
Document No.DC130-003910 Revision 1.0
www.panelook.com
Note (3) Definition of Response Time: Sum of TR and T
white(TFT OFF)black(TFT ON)white(TFT OFF)
T
R
100%
90%
Optical
response
10%
0%
Note (4) Optical characteristic measurement setup
LCD Panel
Field = 1
F
T
F
time
o
Photo-detector (BM-5A)
120cm
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Document TitleHSD190MGW1 Specification for Roadwell Page No. 11/ 28
Document No.DC130-003910 Revision 1.0
Note (5) Definition of Center Luminance of White
Center Luminance= Y1
www.panelook.com
1/10V
1/10V
1/10 H
1/10H
1/2H
Y1
Note (6) Definition of brightness uniformity
1/2V
(Min Luminance of 9 points)
Luminance uniformity = x 100%
(Max Luminance of 9 points)
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Document TitleHSD190MGW1 Specification for Roadwell Page No. 12/ 28
Document No.DC130-003910 Revision 1.0
4.0 BLOCK DIAGRAM
4.1 LCD Module Block Diagram:
TCON with
LVDS r e ceiver
www.panelook.com
X-driver IC
Liquid Crystal Panel
Connector CN1
DC/DC
Converter
Gamma
Reference
Voltage
Generator
900 pixels
1440
Y-d riv er I C
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Document TitleHSD190MGW1 Specification for Roadwell Page No. 13/ 28
Document No.DC130-003910 Revision 1.0
4.2 Back Light Unit
www.panelook.com
1 Hot 1
2 Cold 1
1 Hot 2
2 Cold 2
Back light lamp
CN2, 3, 4, 5.
4.3 Pixel Format
1,1
1,2
(odd)
(even)
(odd)
2,1
(odd)
900
,1
1,3
1,4
(even)
R
R
1440 Pixels
LCD Display Area
1 Pixel
R
B
G
1,
1440
1440
900
1 Hot 1
2 Cold 1
1 Hot 2
2 Cold 2
900 Lines
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Document TitleHSD190MGW1 Specification for Roadwell Page No. 14/ 28
Document No.DC130-003910 Revision 1.0
4.4 Relationship Between Displayed Color and Input
L L L L L L L L H H H H H H L L L L L L L L L LL255
L L L L L L L L H H H H H H H L L L L L L L L LL255
LLLLLLLLLLLLLLLLLLLLLLLHL1
ХΝΝΝL3ΞЦ
LLLLLLLLLLLLLLLLHH HHHHLLL255
LLLLLLLLLLLLLLLLHHHHHHHLL255
LLLLLLLHLLLLLLLHLLLLLLLHL1
ХΝΝΝL3ΞЦ
H H H H H H L L H H H H H H L L H H H H H H L LL252
H H H H H H H L H H H H H H H L H H H H H H H LL254
Basic
color
Gray scale
of Red
Gray scale
of Green
Gray scale
of Blue
Gray scale
of White &
Black
Display
Black LLLLLLLLLLLLLLLLLLLLLLLL-
Blue LLLLLLLLLLLLLLLLHHHHHHHH-
Green L L L L L L L L H H H H HHHHL L L L L L L L-
Light BlueL LL LL L L LHHHHHHHHHHHHHHHH-
Red HHHHHHHHLLLLLLLLLLLLLLLLPurple HHHHHHHHLLLLLLLLHHHHHHHHYellow HHHHHHHHHHHHHHHH L L L L L L L L-
White HHHHHHHHHHHHHHHHHHHHHHHHBlack LLLLLLLLLLLLLLLLLLLLLLLLL0
Dark LLLLLLHLLLLLLLLLLLLLLLLLL2
Light HHHHHHLHLLLLLLLLLLLLLLLLL255
Red HHHHHHHHLLLLLLLLLLLLLLLL Red L255
Black LLLLLLLLLLLLLLLLLLLLLLLLL0
Dark LLLLLLLLLLLLLLHLLLLLLLLLL2
Light L L L L L L L L H H H H H H L H L L L L L L L LL255
Green L L L L L L L L H H H H HHHHL L L L L L L LGreen L255
Black LLLLLLLLLLLLLLLLLLLLLLLLL0
Dark LLLLLLLLLLLLLLLLLLLLLLHLL2
Light LLLLLLLLLLLLLLLLHHHHHHLHL255
Blue LLLLLLLLLLLLLLLLHHHHHHHH Blue L255
Black LLLLLLLLLLLLLLLLLLLLLLLLL0
Dark LLLLLLHLLLLLLLHLLLLLLLHLL2
Light H H H H H H L H H H H H H H L H H H H H H H L HL253
White HHHHHHHHHHHHHHHHHHHHHHHHWhite L255
www.panelook.com
Level
L251
L251
L251
L251
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Document TitleHSD190MGW1 Specification for Roadwell Page No. 15/ 28
Document No.DC130-003910 Revision 1.0
5.0 I/O CONNECTION PIN ASSIGNMENT
5.1 Interface Connector (30-pins ) (JAE:
Pin No. Signal Description
1 RinO0- Receiver Signal (-)
2 RinO0+ Receiver Signal (+)
3 RinO1- Receiver Signal (-)
4 RinO1+ Receiver Signal (+)
5 RinO2- Receiver Signal (-)
6 RinO2+ Receiver Signal (+)
www.panelook.com
FI-XB30SSRL-HF16 or equivalent
)
7 VSS Ground
8 RinOC- Clock Signal (-)
9 RinOC+ Clock Signal (+)
10 RinO3- Receiver Signal (-)
11 RinO3+ Receiver Signal (+)
12 RinE0- Receiver Signal (-)
13 RinE0+ Receiver Signal (+)
14 VSS Receiver Signal (+)
15 RinE1- Receiver Signal (-)
16 RinE1+ Receiver Signal (+)
17 VSS Ground
18 RinE2- Receiver Signal (-)
19 RinE2+ Receiver Signal (+)
20 RinEC- Clock Signal (-)
21 RinEC+ Clock Signal (+)
22 RinE3- Receiver Signal (-)
23 RinE3+ Receiver Signal (+)
24 VSS Ground
25 NC NC
26 NC NC
27 NC NC
28 VDD+5V Power Supply, 5V (Typical)
29 VDD+5V Power Supply, 5V (Typical)
30 VDD+5V Power Supply, 5V (Typical)
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Document TitleHSD190MGW1 Specification for Roadwell Page No. 16/ 28
Document No.DC130-003910 Revision 1.0
5.2 Back Light Unit (CCFL) Connectors:
CN2, 3, 4, 5: CCFL Power Source (Yeonho 35001H5-02 or equivalent)
Pin No. Symbol Color Function
1 Hot1 Pink CCFL power supply (High voltage)
2 Cold1 White Ground
www.panelook.com
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
V
Document TitleHSD190MGW1 Specification for Roadwell Page No. 17/ 28
Document No.DC130-003910 Revision 1.0
6.0 ELECTRICAL CHARACTERISTICS
6.1 TFT LCD Module:
Item SymbolMin. Typ. Max. Unit Note
Voltage of power supply VDD 4.5 5.0 5.5 V
Current of power supply IDD 650 750 850 mA (1)
Vsync frequency fV 60 60 75 Hz (2)
Hsync frequency fH 55.5 59.9 75 KHz
Frequency f
Input rush current I
www.panelook.com
44.37553.25 68.375 MHz
DCLK
--- --- 1.5 A (3)
RUSH
Note (1)
Mosaic: 2 Dot checker image
L0
Grey scale:L0~L255
L0: Luminance with all pixels black.
L255: Luminance with all pixels white.
Note (2) When fv is too low, a flicker may be occurred on the display.
Note (3) Input Rush Current condition
L31
5
0.9VDD
GND
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
0.1VDD
700us~10ms
www.panelook.com
Global LCD Panel Exchange Center
Document TitleHSD190MGW1 Specification for Roadwell Page No. 18/ 28
Document No.DC130-003910 Revision 1.0
6.2 Back-Light Unit
The back-light system is an direct-lighting type with 4CCFLs
characteristics of the lamp are shown in the following tables.
Item SymbolMin. Typ. Max. Unit Note
Lamp current IL 3.0 6.5 9.0 mA(rms)(1)
Lamp voltage VL 612 680 748 V(rms)IL=6.5mA
Frequency fL 40 50 80 KHz (2)
Operating Lifetime
Startup voltage Vs
www.panelook.com
(Cold Cathode Fluorescent Lamp)
Hr 50,000-- -- Hour 6.5mA(3)
Hr 40,000-- -- Hour 7.5mA(3)
1,450 at 25oC
1,700
-- -- V(rms)
at 0
o
C
. The
1
1
2
1
2
2
1
2
A
A
INVERTER
TDK TBD332LR
LCD MODULE
1
1
2
2
1
1
2
2
Note (1)
Lamp current is measured with current meter for high frequency as shown below. Specified
values are for a single lamp. To exceed 6.5 mA, life time accelerate drop down and if to
exceed 9.0 mA has safety problem. If current lower than 3.5 mA, CCFL would be unstable or
damaged.
Note (2)
Lamp frequency may produce interference with horizontal synchronous frequency and this
may cause ripple noise on the display. Therefore lamp frequency shall be kept away from the
horizontal synchronous frequency and its harmonics as far as possible in order to avoid
interference.
A
A
Note (3)
Lamp life time (Hr) can be defined as the time in which it continues to operate under the
condition : Ta=25±3
o
C, Typical IL value indicated in the above table and fL=48 kHz until the
brightness becomes less than 50%
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Document TitleHSD190MGW1 Specification for Roadwell Page No. 19/ 28
Document No.DC130-003910 Revision 1.0
Note (4)
CCFL inverter should be able to provide a voltage over specified value (Vs) in the above table.
Lamp units need at least Vs value shown above to ignition.
Note (5)
The voltage over specified value (Vs) should be applied to the lamp more than 1 second after
startup. Otherwise, the lamp may not be turned on. The used lamp current is the lamp typical
current.
Note (6)
The output voltage waveform and current waveform of the inverter must be symmetrical
(Unsymmetrical ratio is less than 10%). Please do not use the inverter which has
unsymmetrical voltage and current waveform, and spike waveform. The inverter design which
can provide the best optical performance, power efficiency, and lamp life should under the
following conditions.
a. The asymmetry rate of the inverter waveform should be less than 10%.
b. The distortion tae of the waveform should be within
c. The inverter output waveform should be better similar to the ideal sine wave.
www.panelook.com
Ѕ
2±10%.
Asymmetry rate = |I
Distortion rate = I
Ip
p-I-p
p
(or I-p) / I
| / I
rms
rms
I-p
x 100%
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
(2)
Document TitleHSD190MGW1 Specification for Roadwell Page No. 20/ 28
Document No.DC130-003910 Revision 1.0
6.3 Interface Timing ( DE mode)
Item Symbol Min. Typ. Max. Unit
Frame Rate-- 56 60 75 Hz
Frame Period t1 910 934 1050 line
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Document TitleHSD190MGW1 Specification for Roadwell Page No. 21/ 28
Document No.DC130-003910 Revision 1.0
www.panelook.com
6.4 Power On / Off Sequence
Power On
Power Supply
0.9V
DD
0.1V
0V
DD
TP1
TP2
Signal
0.6V0.6V
0V
Backlight
(Recommended)
Item Min. Typ. Max. Unit Remark
TP5
50%
ΚΚΚΚ
TP6
50%
Power Off
0.9V
TP3
DD
0.1V
DD
TP4
0.1V
DD
TP1 0.5 -- 10 msec
TP2 0 -- 50 msec
TP3 0 -- 50 msec
TP4 500 -- -- msec
TP5 200 -- -- msec
TP6 200 -- -- msec
NoteΚ(1) The supply voltage of the external system for the module input should be the same as the
definition of V
DD
.
(2) Apply the lamp volatge within the LCD operation range. When the back-light turns on
before the LCD operation or the LCD truns off before the back-light turns off, the display
may momentarily become white.
(3) In case of VDD = off level, please keep the level of input signal on the low or keep a high
impedance.
(4) TP4 should be measured after the module has been fully discharged between power off
and on period.
(5) Interface signal shall not be kept at high impedance when the power is on.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Document TitleHSD190MGW1 Specification for Roadwell Page No. 22/ 28
Document No.DC130-003910 Revision 1.0
7.0 OUTLINE DIMENSION
7.1 Front View: Date: 2005.12.05
www.panelook.com
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Document TitleHSD190MGW1 Specification for Roadwell Page No. 23/ 28
Document No.DC130-003910 Revision 1.0
BM Assembly Tolerance
| A-A’ | 1 (mm)
| B-B’ | 1 (mm)
www.panelook.com
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Document TitleHSD190MGW1 Specification for Roadwell Page No. 24/ 28
Document No.DC130-003910 Revision 1.0
7.2 Back View: Date: 2008.11.
www.panelook.com
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Document TitleHSD190MGW1 Specification for Roadwell Page No. 25/ 28
Document No.DC130-003910 Revision 1.0
8.0 LOT MARK
8.1 Lot Mark
www.panelook.com
˞˟ˠˡˢˣˤ˥˦
101112131415
code 1,2,3,4,5,6: HannStar internal flow control code.
code 7: production location.
code 8: production year.
code 9: production month.
code 10,11,12,13,14,15: serial number.
(1) The label is attached to the backside of the LCD module.
(2) This is subject to change without prior notice.
HSD190MGW1
Hannstar Display Corporation
MADE IN TAIWAN
-A04
Rev:
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
RoHS
Lot mark
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Document TitleHSD190MGW1 Specification for Roadwell Page No. 26/ 28
Document No.DC130-003910 Revision 1.0
9.0 PACKAGE SPECIFICATION
9.1 Packing form
(1) package quantity in one carton: 8 pieces.
(2) carton size:544 mm
(3) for domestic transportation only.
308 mm
www.panelook.com
H
406 mm.
9.2 Packing assembly drawings
ʳʳʳʳʳʳʳʳʳʳʳʳʳʳʳʳʳʳʳʳʳʳ
ʳ
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Document TitleHSD190MGW1 Specification for Roadwell Page No. 27/ 28
Document No.DC130-003910 Revision 1.0
10.0 GENERAL PRECAUTION
10.1 Use Restriction
This product is not authorized for use in life supporting systems, aircraft navigation control
systems, military systems and any other application where performance failure could be
life-threatening or otherwise catastrophic.
10.2 Disassembling or Modification
Do not disassemble or modify the module. It may damage sensitive parts inside LCD
module, and may cause scratches or dust on the display. HannStar does not warrant the
module, if customers disassemble or modify the module.
www.panelook.com
10.3 Breakage of LCD Panel
10.3.1 If LCD panel is broken and liquid crystal spills out, do not ingest or inhale liquid
crystal, and do not contact liquid crystal with skin.
10.3.2 If liquid crystal contacts mouth or eyes, rinse out with water immediately.
10.3.3 If liquid crystal contacts skin or cloths, wash it off immediately with alcohol and
rinse thoroughly with water.
10.3.4 Handle carefully with chips of glass that may cause injury, when the glass is
broken.
10.4 Electric Shock
10.4.1 Disconnect power supply before handling LCD module.
10.4.2 Do not pull or fold the CCFL cable.
10.4.3 Do not touch the parts inside LCD modules and the fluorescent lamp’s connector
or cables in order to prevent electric shock.
10.5 Absolute Maximum Ratings and Power Protection Circuit
10.5.1 Do not exceed the absolute maximum rating values, such as the supply voltage
variation, input voltage variation, variation in parts’ parameters, environmental
temperature, etc., otherwise LCD module may be damaged.
10.5.2 Please do not leave LCD module in the environment of high humidity and high
temperature for a long time.
10.5.3 It’s recommended employing protection circuit for power supply.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Document TitleHSD190MGW1 Specification for Roadwell Page No. 28/ 28
Document No.DC130-003910 Revision 1.0
10.6 Operation
10.6.1 Do not touch, push or rub the polarizer with anything harder than HB pencil lead.
Use fingerstalls of soft gloves in order to keep clean display quality, when
Persons handle the LCD module for incoming inspection or assembly.
10.6.2 When the surface is dusty, please wipe gently with absorbent cotton or other soft
material.
10.6.3 Wipe off saliva or water drops as soon as possible. If saliva or water drops
contact with polarizer for a long time, they may causes deformation or color
fading.
10.6.4 When cleaning the adhesives, please use absorbent cotton wetted with a little
petroleum benzine or other adequate solvent.
www.panelook.com
10.7 Mechanism
Please mount LCD module by using mounting holes arranged in four corners tightly.
10.8 Static Electricity
10.8.1 Protection film must remove very slowly from the surface of LCD module to
prevent from electrostatic occurrence.
10.8.2 Because LCD module uses CMOS-IC on circuit board and TFT-LCD panel, it is
very weak to electrostatic discharge. Please be careful with electrostatic discharge.
10.8.3 Persons who handle the module should be grounded through adequate methods.
10.9 Strong Light Exposure
The module shall not be exposed under strong light such as direct sunlight. Otherwise,
display characteristics may be changed.
10.10 Disposal
When disposing LCD module, obey the local environmental regulations.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.