HannStar HSD190MEN3-A Product Specification

H a n n Star D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
Document Title HSD190MEN3 Formal Standard Specification Page No. 1 / 34
Document No. Revision 1.0
To :
Date : Nay. 21, 2010
Customer Acceptance Specification
Model : HSD190MEN3
- A**
相關文件:
www.jxlcd.com
www.jxlcd.com
Accepted by:
Proposed by: Technical Service Division
Signature Date
Note:
1. Please contact HannStar Display Corp. before designing your product based on this module specification.
2. The information contained herein is presented merely to indicate the characteristics and performance of our products. No responsibility is assumed by HannStar for any intellectual property claims or other problems that may result from application based on the module described herein.
Signature Date
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n Star D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
Document Title HSD190MEN3 Formal Standard Specification Page No. 2 / 34
Document No. Revision 1.0
Record of Revisions
Rev.
1.0 May, 21,2010
Date Sub-Model
A**
www.jxlcd.com
www.jxlcd.com
Formal Product Specification was first released.
Description of change
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n Star D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
Document Title HSD190MEN3 Formal Standard Specification Page No. 3 / 34
Document No. Revision 1.0
Contents
1.0 General Descriptions ……………………………….… p.5
2.0 Absolute Maximum Ratings ………………………….. p.6
3.0 Optical Characteristics ……………………………….. p.8
4.0 Block Diagram ………………………………………… p.12
5.0 I/O Connection Pin Assignment …………………….. p.15
6.0 Electrical Characteristics ………………….……….. p.16
7.0 Outline Dimension …………………………….……… p.24
8.0 Lot Mark ……………………………………………….. p.26
9.0 Package Specification ……………………………...… p.27
10.0 General Precaution …………………………………… p.28
www.jxlcd.com
11.0 HSD190MEN3- A03 …………………………………… p.31
www.jxlcd.com
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n Star D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
Document Title HSD190MEN3 Formal Standard Specification Page No. 4 / 34
Document No. Revision 1.0
1.0 GENERAL DESCRIPTIONS
1.1 Introduction
HannStar Display model HSD190MEN3-A** is a color active matrix thin film transistor (TFT) liquid crystal display (LCD) that uses amorphous silicon TFT as a switching device. This model is composed of a TFT LCD panel, the voltage reference, common voltage, DC-DC converter, column, and row driver circuit. This TFT LCD has a 19-inch diagonally measured active display area with SXGA resolution (1024 vertical by 1280 horizontal pixel array) .
1.2 Features
19”SXGA TFT LCD Panel
4 CCFLs Backlight System
Supported SXGA (V:1024 lines, H:1280 pixels) Resolution
Supported to 75Hz Refresh Rate
LCD Timing Controller
RoHS Compliance
VESA Compatible
TCO’03 Compliance [Remark(1)]
1.3 Applications
Desktop Monitors
Display terminals for AV applications
Monitors for industrial applications
1.4 General information
www.jxlcd.com
www.jxlcd.com
Outline dimension 396 * 324 * 16.5(Typ) mm Display area 376.32 (H) x301.056 (V) (19.0” diagonal) mm Number of Pixel 1280(H) x 1024(V) Pixels Pixel pitch 0.294(H) x 0.294(V) mm Pixel arrangement RGB Vertical Stripe Display color 16.7M (6-bits+Hi FRC) Color temperature 6500K Display mode Normally white Surface treatment Antiglare, Hard-Coating (3H) Weight 2250 (Please refer to page 34 weight list) g Back-light 4-CCFLs, Top & bottom edge side Input signal 2-ch LVDS
Power consumption
Item Specification
System 3.5(Typ.) B/L 19.8(Typ.)
Unit
W
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
20 40 60
50
65
Document Title HSD190MEN3 Formal Standard Specification Page No. 5 / 34
Document No. Revision 1.0
Remark(1): There are two functions, brightness and contrast tuning, to let luminance to 125cd/m2 in OSD. OSD shouldn't restrict the panel's G-T curve for brightness to be 125cd/m2. The higher contrast, the higher angular uniformity. That is to say, if OSD want to tune the panel's luminance to 125 cd/m2, the suitable way is to only tune the brightness function. And if tuning the brightness function to 125 cd/m2, it would be better only to tuning the inverter, not the gray level.
1.5 Mechanical Information
Item Min. Typ. Max. Unit
Horizontal(H) 395.5 396.0 396.5 mm
Module Size
Vertical(V) 323.5 324.0 324.5 mm
Depth(D) 16.5 mm
Weight (without inverter) -- 2250 -- g
Torque of customer screw hole -- -- 3.0 Kgf*Cm
2.0 ABSOLUTE MAXIMUM RATINGS
2.1 Absolute Rating of Environment
Item Symbol Min. Max. Unit Note Storage temperature T Operating temperature T Vibration (non-operating) V
www.jxlcd.com
Shock (non-operating) S
www.jxlcd.com
Storage humidity H Operating humidity HOP 10 90 %RH (4) Low pressure (operating) P Low pressure (non-operating) P
Note (1)Storage /Operating temperature
Storage Range
-40
-20
STG OPR NOP NOP STG
LOP
LNOP
Humidity (%)
100
90
80
60
40 20
10
0
0
Temperature (oC)
-20 60 0 50
o
C
o
C (1)
-- 1.5 G (2)
-- 70 G (3) 10 90 %RH (3)
697 -- HPa (5)
116 -- HPa (6)
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
Document Title HSD190MEN3 Formal Standard Specification Page No. 6 / 34
Document No. Revision 1.0
(2) 5-500-5Hz sine wave, X, Y, Z each directions, 30 min/cycle. (3) 11ms, ±X, ±Y, ±Z direction, one time each. For this shock test, It is necessary to fill the silicon rubber between the shock jig as buffer. (4) Max wet bulb temp. =39oC (5) 2 hrs. (10000 feet) (6) 24hrs. (50000 feet)
2.2 Electrical Absolute Rating:
2.2.1 TFT LCD Module:
Item Symbol Min. Max. Unit. Note
Power supply Voltage VDD -0.3 5.5 V(DC) (1)(2)
2.2.2 Back Light Unit:
Item Symbol Min. Max. Unit Note
Lamp current IL 3.0 8.0 mA (1)(2)(3)
Lamp frequency fL 40 80 KHz (1)(2)(3)
Note: (1) Permanent damage may occur to the LCD module if beyond this specification.
Functional operation should be restricted to the conditions described under Normal Operating Conditions.
(2) To exceed 7.5mA, life time accelerate drop down and if to exceed 8.0 mA has safety
www.jxlcd.com
www.jxlcd.com
problem. If current lower than 3.0 mA, CCFL would be unstable or damaged.
(3) Within Ta=25±2°C
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
Document Title HSD190MEN3 Formal Standard Specification Page No. 7 / 34
Document No. Revision 1.0
3.0 OPTICAL CHARACTERISTICS
3.1 Optical specification
Item Symbol Condition Min. Typ. Max.
Contrast CR 700 1000 Response time
Rising
TR +TF
Falling
-- 1.2 2.4
-- 3.8 7.6
-- (1)(2)
Unit Note
msec
(1)(3)
White luminance (center of screen)
Color chromaticity (CIE1931)
Red
Gree
n
Blue
YL 250 300 -- cd/m
Θ
=0o
Rx Ry Gx
Gy Bx By
Wx
φ=0o
Normal viewing
angle
-0.03
0.641
0.337
0.304
0.620
0.141
0.073
0.313
+0.03
White
Wy
Θ
75
Hor.
Viewing angle
www.jxlcd.com
www.jxlcd.com
Ver.
Hor.
Viewing angle
Ver.
Brightness uniformity B
L
Θ
75
R
Θ
70
H
Θ
L
Θ
75
L
Θ
75
R
Θ
75
H
Θ
L
UNI
CR>10
CR>5
Θ
=0o
φ=0o
70
75 75 -- -- % (6)
0.329 85 85 80 80 85 85 85 85
--
--
--
--
--
--
--
--
(1)(4)
2
(IL=7.5mA)
(1)(4)
3.2 Measuring Condition
Measuring surrounding: dark room
Lamp current IBL: (7.5) mA, Inverter: TBD332NR
V
Surrounding temperature: 25±2oC
30min. Warm-up time.
be disclosed, distributed or reproduced in whole or in part without Corporation.
=5.0V, fV=60Hz, f
DD1
=54MHz
DCLK
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
o
Document Title HSD190MEN3 Formal Standard Specification Page No. 8 / 34
Document No. Revision 1.0
3.3 Measuring Equipment
FPM520 of Westar Display technologies, INC., which utilized SR-3 for Chromaticity and BM-5A for other optical characteristics.
Measuring spot size: 20~21mm
Note (1) Definition of Viewing Angle:
Note (2) Definition of Contrast Ratio(CR) : measured at the center point of panel
Luminance with all pixels white (L255) CR = Luminance with all pixels black (L0)
www.jxlcd.com
www.jxlcd.com
Θ
=90
L
Θ
L
6’ o’clock
Φ
Φ
=90
L
L
Φ
H
12’ o’clock
H
R
=90
o
Θ
=90o
R
Φ
Θ
o
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
Document Title HSD190MEN3 Formal Standard Specification Page No. 9 / 34
Document No. Revision 1.0
Note (3) Definition of Response Time: Sum of TR and TF
white(TFT OFF) black (TFT ON) white(TFT OFF)
T
R
100%
90%
Optical response
Note (4) Optical characteristic measurement setup
LCD Panel
www.jxlcd.com
www.jxlcd.com
10%
0%
120cm
Field = 1
o
T
F
Photo-detector (BM-5A)
time
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
Y1
Document Title HSD190MEN3 Formal Standard Specification Page No. 10 / 34
Document No. Revision 1.0
Note (5) Definition of Center Luminance of White (center) Center Luminance= Y1
1/10V
1/10 H
1/2H
1/10H
1/2V
1/10V
www.jxlcd.com
www.jxlcd.com
Note (6) Definition of brightness uniformity
(Min Luminance of 9 points)
Luminance uniformity = x 100%
(Max Luminance of 9 points)
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
Document Title HSD190MEN3 Formal Standard Specification Page No. 11 / 34
Document No. Revision 1.0
4.0 BLOCK DIAGRAM
4.1 LCD Module Block Diagram:
Connector CN1
Converter
www.jxlcd.com
www.jxlcd.com
TCON with
LVDS receiver
DC/DC
Y-driver IC
Gamma
Reference
Voltage
Generator
X-driver IC
Liquid Crystal Panel
1280×1024 pixels
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
Back light lamp
1024
280
LCD Display Area
RRBRG
(even)
(odd)
Document Title HSD190MEN3 Formal Standard Specification Page No. 12 / 34
Document No. Revision 1.0
4.2 Back Light Unit
1 Hot 1 (Red) 2 Cold 1 (White)
1 Hot 2 (Blue) 2 Cold 2 (Black)
CN2, 3, 4, 5.
Note: The design of same polarity lamp voltage in the same lamp side of the panel is highly recommended.
www.jxlcd.com
4.3 Pixel Format
www.jxlcd.com
1 Hot 1 (Red) 2 Cold 1 (White)
1 Hot 2 (Blue) 2 Cold 2 (Black)
1,1
1,2
1,3
(odd)
2,1
(odd)
1,4
(even)
1 Pixel
1024
,1
1280 Pixels
be disclosed, distributed or reproduced in whole or in part without Corporation.
1280
1
1,
1024 Lines
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
H H H H H L L L L L L L L L L
H H H H H L L
Document Title HSD190MEN3 Formal Standard Specification Page No. 13 / 34
Document No. Revision 1.0
4.4 Relationship Between Displayed Color and Input
MSB LSB MSB LSB MSB LSB Gray scale Display
Black L L L L L L L L L L L L L L L L L L L L L L L L
Blue L L L L L L L L L L L L L L L L H H H H H H H H
Green L L L L L L L L H H H H H H H H L L L L L L L L Basic color
Gray scale of Red
Gray scale of Green
Gray scale of Blue
Gray scale of White & Black
Light Blue L L L L L L L L H H H H H H H H H H H H H H H H
Red H H H H H H H H L L L L L L L L L L L L L L L L Purple H H H H H H H H L L L L L L L L H H H H H H H H Yellow H H H H H H H H H H H H H H H H L L L L L L L L
White H H H H H H H H H H H H H H H H H H H H H H H H Black L L L L L L L L L L L L L L L L L L L L L L L L
Dark L L L L L L H L L L L L L L L L L L L L L L L L
Light H H H H H H L H L L L L L L L L L L L L L L L L L253
Red H H H H H H H H L L L L L L L L L L L L L L L L Red L255
Black L L L L L L L L L L L L L L L L L L L L L L L L
Dark L L L L L L L L L L L L L L H L L L L L L L L L
www.jxlcd.com
www.jxlcd.com
Light L L L L L L L L H H H H H H L H L L L L L L L L L253
Green L L L L L L L L H H H H H H H H L L L L L L L L Green L255
Black L L L L L L L L L L L L L L L L L L L L L L L L
Dark L L L L L L L L L L L L L L L L L L L L L L H L
Light L L L L L L L L L L L L L L L L H H H H H H L H L253
Blue L L L L L L L L L L L L L L L L H H H H H H H H Blue L255
Black L L L L L L L L L L L L L L L L L L L L L L L L
Dark L L L L L L H L L L L L L L H L L L L L L L H L
Light H H H H H H L H H H H H H H L H H H H H H H L H L253
White H H H H H H H H H H H H H H H H H H H H H H H H White L255
R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0
L L L L L L L H L L L L L L L L L L L L L L L L
H H H H H H L L L L L L L L L L L L L L L L L L L252
H H H H H H H L L L L L L L L L L L L L L L L L L254
L L L L L L L L L L L L L L L H L L L L L L L L
L L L L L L L L H
L L L L L L L L H H H H H H H L L L L L L L L L L254
L L L L L L L L L L L L L L L L L L L L L L L H
L L L L L L L L L L L L L L L L H
L L L L L L L L L L L L L L L L H H H H H H H L L254
L L L L L L L H L L L L L L L H L L L L L L L H
H H H H H H L L H H H H H H L L H H H H H H L L L252
H H H H H H H L H H H H H H H L H H H H H H H L L254
L3L251
L3L251
L3L251
L3L251
Level
L0 L1 L2
L0 L1 L2
L252
L0 L1 L2
L252
L0 L1 L2
-
-
-
-
-
-
-
-
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
Document Title HSD190MEN3 Formal Standard Specification Page No. 14 / 34
Document No. Revision 1.0
5.0 I/O CONNECTION PIN ASSIGNMENT
5.1 Interface Connector (30-pins, HRS MDF76URW-30S-1H or equivalent) Pin No. Signal Description
1 RinO0- Receiver Signal (-) 2 RinO0+ Receiver Signal (+) 3 RinO1- Receiver Signal (-) 4 RinO1+ Receiver Signal (+) 5 RinO2- Receiver Signal (-) 6 RinO2+ Receiver Signal (+) 7 VSS Ground 8 RinOC- Clock Signal (-)
9 RinOC+ Clock Signal (+) 10 RinO3- Receiver Signal (-) 11 RinO3+ Receiver Signal (+) 12 RinE0- Receiver Signal (-) 13 RinE0+ Receiver Signal (+) 14 VSS Ground 15 RinE1- Receiver Signal (-) 16 RinE1+ Receiver Signal (+) 17 VSS Ground 18 RinE2- Receiver Signal (-) 19 RinE2+ Receiver Signal (+)
www.jxlcd.com
www.jxlcd.com
5.2 Back Light Unit (CCFL) Connectors:
CN2, 3, 4, 5: CCFL Power Source (Yeonho 35001HS-02 or equivalent)
20 RinEC- Clock Signal (-) 21 RinEC+ Clock Signal (+) 22 RinE3- Receiver Signal (-) 23 RinE3+ Receiver Signal (+) 24 VSS Ground 25 VSS Ground 26 NC NC 27 VSS Ground 28 VDD+5V Power Supply, 5V (Typical) 29 VDD+5V Power Supply, 5V (Typical) 30 VDD+5V Power Supply, 5V (Typical)
Pin No. Symbol Color Function
1 Hot1 Pink CCFL power supply (High voltage) 2 Cold1 White Ground
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
Document Title HSD190MEN3 Formal Standard Specification Page No. 15 / 34
Document No. Revision 1.0
6.0 ELECTRICAL CHARACTERISTICS
6.1 TFT LCD Module:
Item Symbol
Voltage of power supply VDD 4.5 5.0 5.5 V
White I
Current of power supply
Vsync frequency fV 50 60 76 Hz (2) Hsync frequency fH 53.3 64 80 KHz Frequency f Input rush current I
Note (1)
(a)White:
V-Color I Mosaic I
DD0 DD1 DD2
DCLK RUSH
Min. Typ. Max. Unit Note
380 480 580 500 600 700 810 1010 1210
50 54 67.5 MHz
-- -- 3.0 A (3)
mA (1) mA (1) mA (1)
www.jxlcd.com
www.jxlcd.com
(b).V-Color :
Yellow
White
Purple
Red
Green
Cyan
Black
Blue
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
Document Title HSD190MEN3 Formal Standard Specification Page No. 16 / 34
Document No. Revision 1.0
(c)Mosaic : 2 Dot checker image
L0
Grey scale:L0~L255
L0: Luminance with all pixels black.
L255: Luminance with all pixels white.
www.jxlcd.com
www.jxlcd.com
Note (2) When fv is too low, a flicker may be occurred on the display. Note (3) Input Rush Current measurement condition
L31
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
0.1VDD
V
Document Title HSD190MEN3 Formal Standard Specification Page No. 17 / 34
Document No. Revision 1.0
www.jxlcd.com
www.jxlcd.com
GND
0.9VDD
5
500us~10ms
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
A
A
A
A
Document Title HSD190MEN3 Formal Standard Specification Page No. 18 / 34
Document No. Revision 1.0
6.2 Back-Light Unit The back-light system is an edge-lighting type with 4 CCFL
The characteristics of the lamp are shown in the following tables.
Item Symbol Lamp current IL 3.0 7.5 8.0 mA(rms) Lamp voltage VL 594 660 726 V(rms) IL=7.5mA Frequency fL 40 50 80 KHz (2) Operating Lifetime Hr 40,000
Startup voltage Vs
LCD MODULE
www.jxlcd.com
www.jxlcd.com
Note (1) Lamp current is measured with current meter for high frequency as shown below. Specified
values are for a single lamp. To exceed 7.5 mA, life time accelerate drop down and if to exceed 9.0 mA has safety problem. If current lower than 3.5 mA, CCFL would be unstable or damaged.
Note (2) Lamp frequency may produce interference with horizontal synchronous frequency and this
may cause ripple noise on the display. Therefore lamp frequency shall be kept away from the horizontal synchronous frequency and its harmonics as far as possible in order to avoid interference.
Note (3) Lamp life time (Hr) can be defined as the time in which it continues to operate under the
condition : Ta=25±3oC, Typical IL value indicated in the above table and fL=48 kHz until the brightness becomes less than 50%
Note (4) CCFL inverter should be able to provide a voltage over specified value (Vs) in the above
table. Lamp units need at least Vs value shown above to ignition.
Min. Typ. Max. Unit Note
-- -- Hour 7.5mA(3) 1400 at 25oC 1650
1 2
1 2
1 2
1 2
-- -- V(rms)
1 2
1 2
1 2
1 2
(Cold Cathode Fluorescent Lamp)
(1)
at 0oC
INVERTER
(TBD332NR)
.
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
Document Title HSD190MEN3 Formal Standard Specification Page No. 19 / 34
Document No. Revision 1.0
Note (5) The voltage over specified value (Vs) should be applied to the lamp more than 1 second
after startup. Otherwise, the lamp may not be turned on. The used lamp current is the lamp typical current.
Note (6) The output voltage waveform and current waveform of the inverter must be symmetrical
(Unsymmetrical ratio is less than 10%). Please do not use the inverter which has unsymmetrical voltage and current waveform, and spike waveform. The inverter design which can provide the best optical performance, power efficiency, and lamp life should under the following conditions.
a. The asymmetry rate of the inverter waveform should be less than 10%. b. The distortion tae of the waveform should be within 2±10%. c. The inverter output waveform should be better similar to the ideal sine wave.
www.jxlcd.com
www.jxlcd.com
Asymmetry rate = |Ip-I-p| / Irms x 100% Distortion rate = Ip (or I-p) / Irms
Note (7) The frequency range from 50 to 60KHz can guarantee both electrical and optical
characteristics. The frequency range from 40 to 80KHz will not effect the characteristics of lifetime and reliability.
Ip
I-p
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
Symbol
Document Title HSD190MEN3 Formal Standard Specification Page No. 20 / 34
Document No. Revision 1.0
6.3 Switching Characteristics for LVDS Receiver
Item
Differential Input High Threshold Vth Differential Input Low Threshold
Input Current I Differential input Voltage |VID|
Common Mode Voltage Offset V Clock Frequency fc 50 54
Vtl -100
IN
CM
www.jxlcd.com
www.jxlcd.com
6.4 Interface Timing ( DE mode)
Item Symbol Min. Typ. Max. Unit Frame Rate Frame Period t1 1029 1066 1150 line Vertical Display Time t2 1024 1024 1024 line Vertical Blanking Time t3 5 42 126 line 1 Line Scanning Time t4 720 844 875 clock Horizontal Display Time t5 640 640 640 clock Horizontal Blanking Time t6 80 204 235 clock Clock Rate t7 50 54 67.5 MHz
-- 50 60 76 Hz
Timing Diagram of Interface Signal (DE mode)
Min. Typ.
-10
0.1
1.15
Max. Unit
+100 mV
+10 uA
0.6 V
1.35 V
67.5 MHz
mV
Conditions
V
CMLVDS
VIN=2.4V/0V,
=1.25V
VDD=3.6V
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
Document Title HSD190MEN3 Formal Standard Specification Page No. 21 / 34
Document No. Revision 1.0
t1
t1
t1t1 t2
t2 t3
t2t2
t3
t3t3
NCLK
t4
t4
t4t4
DE
X,
X,
X,
X,
X,
R,G,B[0:7]
t7
t7
t7t7
X,1
X,1X,1
X,1
X,2
X,2
X,2X,2
X,3
X,3
X,3X,3
X,4
X,4X,4
X,4
X,Y
X,Y
X,YX,Y
t4
t4
t4t4
X,X,
1022
1022
10221022
1023
1023
10231023
X,
X,X,
1024
1024
10241024
X,X,
X,1
X,1 X,2
X,1X,1
X,2
X,2X,2
NCLK
t5
t5 t6
t5t5
t6
t6t6
DE
R,G,B[0:7]
123
4
www.jxlcd.com
www.jxlcd.com
7
5 6
91011
8
12
1269 1270
1271 1272
1273 1274
1275 1276
1277 1278
1279 1280
12345
6
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
0.9V
0.9V
Document Title HSD190MEN3 Formal Standard Specification Page No. 22 / 34
Document No. Revision 1.0
6.5 Power On / Off Sequence
Power On
Power Supply
0.1V
0V
Signal
0V
(Recommended)
DD
TP1
TP2
0.6V
TP5
Backlight
50%
Power Off
TP6
50%
TP3
0.6V
0.1V
DD
TP4
0.1V
DD
Note(1) The supply voltage of the external system for the module input should be the same as the
www.jxlcd.com
www.jxlcd.com
Item Min. Typ. Max. Unit Remark
TP1 0.5 -- 10 msec TP2 0 -- 50 msec TP3 0 -- 50 msec TP4 500 -- -- msec TP5 200 -- -- msec TP6 200 -- -- msec
definition of VDD.
(2) Apply the lamp volatge within the LCD operation range. When the back-light turns on
before the LCD operation or the LCD truns off before the back-light turns off, the display may momentarily become white.
(3) In case of VDD = off level, please keep the level of input signal on the low or keep a high
impedance.
(4) TP4 should be measured after the module has been fully discharged between power off
and on period.
(5) Interface signal shall not be kept at high impedance when the power is on.
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
Document Title HSD190MEN3 Formal Standard Specification Page No. 23 / 34
Document No. Revision 1.0
7.0 OUTLINE DIMENSION
7.1 Front View: Date: 2007.1.11
B
B
B-B
: 3:1
www.jxlcd.com
p
www.jxlcd.com
U
A-A
: 3:1
A
A
n w o D
BM Assembly Tolerance
| A-A’ | 1 (mm)
| B-B’ | 1 (mm)
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
Document Title HSD190MEN3 Formal Standard Specification Page No. 24 / 34
Document No. Revision 1.0
7.2 Back View: Date: 2007.1.11
www.jxlcd.com
www.jxlcd.com
1.Backlight: 4 CCFL
2. I/F Connector Specification (CN1): FI-XB30SSRL-HF16 or Equivalent
3. Lamp Connector (CN2~CN5) / Wire Specification: Yeon-Ho 35001HS-02L or Equivalent / 2Pin x L170mm
4. User Mounting Torque Spec: 3 Kgf-cm Max.
5. Unspecificed Tolerance is ±0.5mm.
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
10
11
12
13
14
15
HSD190
MEN3
Rev:
Document Title HSD190MEN3 Formal Standard Specification Page No. 25 / 34
Document No. Revision 1.0
8.0 LOT MARK
8.1 Lot Mark
code 1,2,3,4,5,6: HannStar internal flow control code. code 7: production location. code 8: production year. code 9: production month. code 10,11,12,13,14,15: serial number.
Note (1) Production Year: Code 8 is defined by the last number of the year. For example:
Year 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010
Mark 1 2 3 4 5 6 7 8 9 0
Note (2) Production Month
Month Jan. Feb. Mar. Apr. May. Jun. Jul. Aug. Sep. Oct Nov. Dec.
Mark 1 2 3 4 5 6 7 8 9 A B C
www.jxlcd.com
www.jxlcd.com
8.2 Location of Lot Mark
(1) The label is attached to the backside of the LCD module. (2) This is subject to change without prior notice.
CN1
-A**
RoHS
Lot mark
Up
Center of Active Area
CN5CN4
CN3
CN2
Down
RISK OF ELECTRIC SHOCK DISCONNECT
THE ELECTRIC POWER BEFORE SERVICING
HIGH VOLTAGE CAUTION
COLD CATHODE FLUORESCENT LAMP IN LCD PANEL CONTAINS
A SMALL AMOUNT OF MERCURY. PLEASE FOLLOW LOCAL
ORDINANCES OR REGULATIONS FOR DISPOSAL.
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
Document Title HSD190MEN3 Formal Standard Specification Page No. 26 / 34
Document No. Revision 1.0
9.0 PACKAGE SPECIFICATION
9.1 Packing form
(1) package quantity in one carton: 8 pieces. (2) carton size: 544±3 mm×302±3 mm×446
(3) for domestic transportation only.
H
±
3 mm.
9.2 Packing assembly drawings
www.jxlcd.com
www.jxlcd.com
M1904 8PCS
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
Document Title HSD190MEN3 Formal Standard Specification Page No. 27 / 34
Document No. Revision 1.0
10.0 GENERAL PRECAUTION
10.1 Use Restriction
This product is not authorized for use in life supporting systems, aircraft navigation control systems, military systems and any other application where performance failure could be life-threatening or otherwise catastrophic.
10.2 Disassembling or Modification
Do not disassemble or modify the module. It may damage sensitive parts inside LCD module, and may cause scratches or dust on the display. HannStar does not warrant the module, if customers disassemble or modify the module.
10.3 Breakage of LCD Panel
10.3.1 If LCD panel is broken and liquid crystal spills out, do not ingest or inhale liquid crystal, and do not contact liquid crystal with skin.
10.3.2 If liquid crystal contacts mouth or eyes, rinse out with water immediately.
10.3.3 If liquid crystal contacts skin or cloths, wash it off immediately with alcohol and rinse thoroughly with water.
10.3.4 Handle carefully with chips of glass that may cause injury, when the glass is
broken.
10.4 Electric Shock
10.4.1 Disconnect power supply before handling LCD module.
10.4.2 Do not pull or fold the CCFL cable.
10.4.3 Do not touch the parts inside LCD modules and the fluorescent lamp’s connector
www.jxlcd.com
www.jxlcd.com
or cables in order to prevent electric shock.
10.5 Absolute Maximum Ratings and Power Protection Circuit
10.5.1 Do not exceed the absolute maximum rating values, such as the supply voltage
variation, input voltage variation, variation in parts’ parameters, environmental temperature, etc., otherwise LCD module may be damaged.
10.5.2 Please do not leave LCD module in the environment of high humidity and high temperature for a long time.
10.5.3 It’s recommended employing protection circuit for power supply.
10.6 Operation
10.6.1 Do not touch, push or rub the polarizer with anything harder than HB pencil lead.
Use fingerstalls of soft gloves in order to keep clean display quality, when persons
handle the LCD module for incoming inspection or assembly.
10.6.2 When the surface is dusty, please wipe gently with absorbent cotton or other soft material.
10.6.3 Wipe off saliva or water drops as soon as possible. If saliva or water drops contact with polarizer for a long time, they may causes deformation or color
fading.
11.6.4 When cleaning the adhesives, please use absorbent cotton wetted with a little petroleum benzene or other adequate solvent.
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
Document Title HSD190MEN3 Formal Standard Specification Page No. 28 / 34
Document No. Revision 1.0
10.7 Mechanism
Please mount LCD module by using mounting holes arranged in four corners tightly.
10.8 Static Electricity
10.8.1 Protection film must remove very slowly from the surface of LCD module to prevent
from electrostatic occurrence.
10.8.2 Because LCD module uses CMOS-IC on circuit board and TFT-LCD panel, it is
very weak to electrostatic discharge. Please be careful with electrostatic
discharge.
10.8.3 Persons who handle the module should be grounded through adequate methods.
10.9 Strong Light Exposure
The module shall not be exposed under strong light such as direct sunlight. Otherwise, display characteristics may be changed.
10.10 Disposal
When disposing LCD module, obey the local environmental regulations.
www.jxlcd.com
www.jxlcd.com
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
Document Title HSD190MEN3 Formal Standard Specification Page No. 29 / 34
Document No. Revision 1.0
HSD190MEN3- A03
(For HVS model adding test connector, the general spec follows –A00)
11.1 Front View: Date: 2007.2.5
B
B
www.jxlcd.com
www.jxlcd.com
B-B
: 3:1
p U
n w
o D
A-A
: 3:1
A
A
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
Document Title HSD190MEN3 Formal Standard Specification Page No. 30 / 34
Document No. Revision 1.0
11.2 Back View: Date: 2007.2.5
Do not Touch
禁止觸摸禁止觸摸
www.jxlcd.com
www.jxlcd.com
Do not Touch
be disclosed, distributed or reproduced in whole or in part without Corporation.
1.Backlight: 4 CCFL
2. I/F Connector Specification (CN1): FI-XB30SSRL-HF16 or Equivalent
3. Lamp Connector (CN2~CN5) / Wire Specification: Yeon-Ho 35001HS-02L or Equivalent / 2Pin x L170mm
4. User Mounting Torque Spec: 3 Kgf-cm Max.
5. Unspecificed Tolerance is ±0.5mm.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
Document Title HSD190MEN3 Formal Standard Specification Page No. 31 / 34
Document No. Revision 1.0
HSD190MEN3- A03
(For this model, the values and definitions of crosstalk and gamma are added.)
Date: 2007.5.18
3.1 OPTICAL CHARACTERISTICS
Optical specification
Item Symbol Condition Min. Typ. Max.
Contrast CR 700 1000 Response time
Rising
TR +TF
Falling
--
5.0 10 msec
--
-- (1)(2)
White luminance
YL 250 300 -- cd/m
(center of screen)
Color chromaticity (CIE1931)
Red
Gree
n
Blue
Rx Ry Gx
Gy Bx By
Wx
Θ
=0o
φ=0o
Normal
viewing
angle
-0.03
0.641
0.337
0.304
0.620
0.141
0.073
0.313
+0.03
White
www.jxlcd.com
www.jxlcd.com
Hor.
Viewing angle
Ver.
Hor.
Viewing angle
Ver.
Brightness uniformity B
Wy
Θ
75
L
Θ
75
R
Θ
75
H
Θ
L
Θ
75
L
Θ
75
R
Θ
75
H
Θ
L
UNI
CR>10
CR>5
Θ
=0o
φ=0o
75
75 75 -- -- % (6)
0.329 85 85 80 80 85 85 85 85
--
--
--
--
--
--
--
--
Unit Note
(1)(3)
(1)(4)
2
(IL=7.5mA)
(1)(4)
Θ
Crosstalk CT(n)
=0
-- -- 4.0 % (7)
φ=0o
NLF 65 Level
Gamma
γ
L8..…L252, L255)
NLF 256 level
(L0, L4,
1.9
2.2 2.5 - (8)
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
V
H
L(3)
V
H
LB(3)
Pattern A
Pattern B
Document Title HSD190MEN3 Formal Standard Specification Page No. 32 / 34
Document No. Revision 1.0
Note (7) Definition of crosstalk CT (1) ~ CT (4)
L (n) – LB (n) CT(n) = x 100% , n = 1 ~ 4 L (n)
Where L(n) = Luminance of point “n” at pattern A (cd/m2) , n=14 LB(n) = Luminance of point “n” at pattern B (cd/m2) , n=14 The location measured will be exactly the same in both patterns. L0: Luminance with all pixels black
L255: Luminance with all pixels white
The measurement sequence is to measure the values of the first point in two
www.jxlcd.com
www.jxlcd.com
Gray scale: L127
1
1 4
V
8
V
1
V
2
1
V
1
4
V
8
1 8
patterns (
Pattern A => Pattern B
) and then that of the second point in two patterns and so on. The measurement of the second point is allowed only after the values of the first point in two patterns are measured.
The measurement sequence:
Pattern B L(3)Pattern A => Pattern B L(4)Pattern A => Pattern B
L(1)
L(4)
L(1)Pattern A => Pattern B L(2)Pattern A =>
Gray scale: L0
1
1
V
8
V
4
Gray scale: L127
LB(1)
LB(4)
1
V
2
1
V
1
4
L(2)
H
1
H
4
1
H
2
H
1 8
1
H
4
V
8
1
H
8
1
4
LB(2)
1 8
1
H
1
H
2
H
H
4
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
(without
Document Title HSD190MEN3 Formal Standard Specification Page No. 33 / 34
Document No. Revision 1.0
Note (8) Definition of Gamma (γ) and use non-linear fitting
(NLF) method.
T %
Gray Level
Weight List: Date: 2009.11.5
1.5 Mechanical Information
Item Model Min. Typ. Max. Unit
A00 (Rev 2, 6)
A01 (Rev 2,5)
-- 2250 -- g
-- 1950 -- g
-- 1860 -- g
Weight
inverter)
www.jxlcd.com
www.jxlcd.com
A02 (Rev 1,4)
A04 (Rev 0)
A10
A00 (Rev 0, 1, 4, 5)
A01 (Rev 0,1,4)
A02 (Rev 0)
A03 (Rev 0,4)
A11
A05 (Rev 0,1)
A06 (Rev 0)
A07 (Rev 0,4)
be disclosed, distributed or reproduced in whole or in part without Corporation.
H a n n St a r D i s p l a y C o r p .
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
Document Title HSD190MEN3 Formal Standard Specification Page No. 34 / 34
Document No. Revision 1.0
M1908-A10 & A11 OPTICAL CHARACTERISTICS:
3.0 OPTICAL CHARACTERISTICS
3.1 Optical specification
Item Symbol Condition Min. Typ. Max.
Contrast CR 550 700 -- (1)(2) Response time
Rising
TR +TF
Falling
-- 1.2 2.4
-- 3.8 7.6
Unit Note
msec
(1)(3)
White luminance (center of screen)
Red
Color chromaticity (CIE1931)
www.jxlcd.com
www.jxlcd.com
Viewing angle
Viewing angle
Brightness uniformity B
Gree
n
Blue
White
Hor.
Ver.
Hor.
Ver.
YL 200 250 -- cd/m
Θ
=0o
Rx Ry Gx
Gy Bx
By Wx Wy
Θ
60
L
Θ
60
R
Θ
60
H
Θ
L
Θ
75
L
Θ
75
R
Θ
75
H
Θ
L
UNI
φ=0o
Normal
viewing
angle
CR>10
CR>5
Θ
=0o
φ=0o
-0.03
50
75 75 -- -- % (6)
0.641
0.337
0.304
0.620
0.141
0.073
0.313
0.329 70 70 70 60 85 85 85 85
+0.03
--
--
--
--
--
--
--
--
(1)(4)
2
(IL=7.5mA)
(1)(4)
be disclosed, distributed or reproduced in whole or in part without Corporation.
Loading...