HannStar HSD173PUW1-A00 Specification

HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
Document Title HSD173PUW1-A Formal Specification Page No. 1/27
Document No. Revision 1.0
HannStar Product Specification
(Formal)
Model: HSD173PUW1
-A
Note: (1) Please contact HannStar Display Corp. before designing your product based on
this module specification.
(2) The information contained herein is presented merely to indicate the characteristics and
performance of our products. No responsibility is assumed by HannStar for any intellectual property claims or other problems that may result from application based on the module described herein.
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
Document Title HSD173PUW1-A Formal Specification Page No. 2/27
Document No. Revision 1.0
Record of Revisions
Rev.
1.0
Date Sub-Model
-- A
Description of change
Formal Product Specification was first released.
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
Document Title HSD173PUW1-A Formal Specification Page No. 3/27
Document No. Revision 1.0
Contents
1.0 General description ………………………………… p.4
2.0 Absolute maximum ratings……………………………. p.5
3.0 Optical characteristics.………………………………. p.6
4.0 Block diagram ……………………………………… p.10
5.0 Interface pin connection …………………………… p.12
6.0 Electrical characteristics …………………………… p.13
7.0 Reliability test items ………………………………… p.21
8.0 Outline dimension …………………………………… p.22
9.0 Lot mark ……………………………………………... p.24
10.0 Package specification ……………………………… p.25
11.0 General precaution …………………………………… p.26
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
Document Title HSD173PUW1-A Formal Specification Page No. 4/27
Document No. Revision 1.0
1.0 GENERAL DESCRIPTION
1.1 Introduction
HannStar Display model HSD173PUW1-A is a color active matrix thin film transistor (TFT) liquid crystal display (LCD) that uses amorphous silicon TFT as a switching device. This model is composed of a TFT LCD panel, a driving circuit and a back light system. This TFT LCD has a 17.3 (16:9) inch diagonally measured active display area with Full HD (1920 horizontal by 1080 vertical pixel) resolution.
1.2 Features
17.3 (16:9 diagonal) inch configuration
Two channel LVDS interface
262K color by 6 bit R.G.B signal input
Color engine
CABC
RoHS Compliance
Halogen Free
1.3 Applications
NB
1.4 General information
Item Specification Unit Outline Dimension 398.1 x 232.8 x 5.5 (Typ.) mm Display area 381.89(H) x 214.81(V) mm Number of Pixel 1920 RGB (H) x 1080(V) pixels Pixel pitch 0.1989(H) x 0.1989(V) mm Pixel arrangement RGB Vertical stripe Display mode Normally white NTSC 60 % Surface treatment Glare, Hard-Coating (3H) Weight 565 (Typ.) g Back-light White LED Power
Consumption
Logic System 1.6 (Max.) W
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
Document Title HSD173PUW1-A Formal Specification Page No. 5/27
Document No. Revision 1.0
1.5 Mechanical Information
Item Min. Typ. Max. Unit
Horizontal (H) 397.6 398.1 368.6 mm
Module
Size
Weight
Vertical (V) 232.3 232.8 233.3 mm Depth (D)
5.5 565 580 g
5.8 mm
2.0 ABSOLUTE MAXIMUM RATINGS
2.1 Electrical Absolute Rating
2.1.1 TFT LCD Module
Item Symbol Min. Max. Unit Note
Logic Supply voltage
2.1.2 Environment Absolute Rating Item Symbol Min. Max. Unit Note
Operating Temperature T Storage Temperature T
VDD -0.3 4.0 V
0 50
opa
-20 60
stg
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
Document Title HSD173PUW1-A Formal Specification Page No. 6/27
Document No. Revision 1.0
3.0 OPTICAL CHARACTERISTICS
3.1 Optical specification
Item Symbol Condition Min. Typ. Max. Unit Note
Contrast CR
Rising
Tr
Response time
Falling
Tf
400 500
2.4 4.8
5.6 11.2
(1)(2)(4)
msec
(1)(3)
White luminance (5 point)
Red
Color
Green
chromaticity (CIE1931)
Blue
White
Hor.
Viewing angle
Ver.
Brightness uniformity B
Brightness Uniformity B
3.2 Measuring Condition
Measuring surroundingdark room
LED current I
Ambient temperature25±2oC
15min. warm-up time.
YL 176 220
Θ=0
Rx RY Gx GY
Bx BY
Wx Wy
Θ
Θ
L
R
Normal viewing
angle
0.582
0.326
0.293
0.564
0.118
0.062
0.283
0.299 70 80 70 80
CR>10
Θ
U
Θ
D
UNI
UNI
20mA / single LED
L
(5point)
(13 points)
Θ
Θ
=0
=0
50 60 65 75
80
70
0.612
0.356
0.323
0.594
0.148
0.092
0.642
0.386
0.353
0.624
0.178
0.122
0.313 0.343
0.329 0.359
(1)(4)(5)
2
cd/m
(IL=20mA)
(1)(4)
% (6)
% (6)
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
o
Document Title HSD173PUW1-A Formal Specification Page No. 7/27
Document No. Revision 1.0
3.3 Measuring Equipment
FPM520 of Westar Display technologies, INC., which utilized SR-3 for Chromaticity and BM-5A for other optical characteristics.
Measuring spot size20 ~ 21 mm
Note (1) Definition of Viewing Angle:
Θ
U
12’ o’clock Φ=90
o
Φ=180
Θ
L
Θ
R
Φ=0o
Θ
D
6’ o’clock Φ=270
o
Note (2) Definition of Contrast Ratio (CR) : measured at the center point of panel
Luminance with all pixels white CR = Luminance with all pixels black
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
Document Title HSD173PUW1-A Formal Specification Page No. 8/27
Document No. Revision 1.0
Note (3) Definition of Response Time : Sum of TR and TF
white(TFT OFF) black (TFT ON) white(TFT OFF)
100%
90%
T
R
T
F
Optical response
10%
0%
time
Note (4) Definition of optical measurement setup
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
Document Title HSD173PUW1-A Formal Specification Page No. 9/27
Document No. Revision 1.0
Note (5) Definition of Average Luminance Uniformity of White (5 Point)
Y1+Y2+Y3+Y4+Y5
Average Luminance Uniformity =
5
Note (6) Definition of brightness uniformity
Luminance uniformity(13points) = ×100%
Luminance uniformity(5 points) = ×100%
(Min Luminance of 5 points) (Max Luminance of 5 points)
(Min Luminance of 13 points) (Max Luminance of 13 points)
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
1920 pixel (5760 Dots)
B G
LED
Document Title HSD173PUW1-A Formal Specification Page No. 10/27
Document No. Revision 1.0
4.0 BLOCK DIAGRAM
X-driver IC
Driver
Timing
Controller
EDID
+
Liquid Crystal Panel
Connector
DC/DC
LVDS
Receiver
Y-driver IC
1920x1080 pixels
Converter
Gray scale
Manipulation
Voltage
Generation
Circuit
4.1 TFT LCD Module:
4.2 Pixel Format
1,1
1,2 1,3 1,4
1,1920
2,1
LCD Display Area
1 Pixel
1080 Lines
R
R
1080,1
R
1080,
1920
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
scale of
Document Title HSD173PUW1-A Formal Specification Page No. 11/27
Document No. Revision 1.0
4.3 Relationship Between Displayed Color and Input
Basic color
Gray scale of Red
Gray scale of Green
Gray scale of Blue
Gray White &
Black
MSB LSB
Display
Black L L L L L L L L L L L L L L L L L L
Blue L L L L L L L L L L L L H H H H H H
Green L L L L L L H H H H H H L L L L L L
Light Blue L L L L L L H H H H H H H H H H H H
Red H H H H H H L L L L L L L L L L L L Purple H H H H H H L L L L L L H H H H H H Yellow H H H H H H H H H H H H L L L L L L
White H H H H H H H H H H H H H H H H H H
Black L L L L L L L L L L L L L L L L L L
Dark
Light
Red H H H H H H L L L L L L L L L L L L Red L63
Black L L L L L L L L L L L L L L L L L L
Dark
Light
Green L L L L L L H H H H H H L L L L L L Green L63
Black L L L L L L L L L L L L L L L L L L
Dark
Light
Blue L L L L L L L L L L L L H H H H H H Blue L63
Black L L L L L L L L L L L L L L L L L L
Dark
Light
White H H H H H H H H H H H H H H H H H H White L63
R5 R4 R3 R2 R1 R0
L L L L L H L L L L L L L L L L L L L L L L H L L L L L L L L L L L L L
↑ ↓
H H H H L H L L L L L L L L L L L L H H H H H L L L L L L L L L L L L L
L L L L L L L L L L L H L L L L L L L L L L L L L L L L H L L L L L L L
↑ ↓
L L L L L L H H H H L H L L L L L L L L L L L L H H H H H L L L L L L L
L L L L L L L L L L L L L L L L L H L L L L L L L L L L L L L L L L H L
↑ ↓
L L L L L L L L L L L L H H H H L H L L L L L L L L L L L L H H H H H L
L L L L L H L L L L L H L L L L L H L L L L H L L L L L H L L L L L H L
↑ ↓
H H H H L H H H H H L H H H H H L H H H H H H L H H H H H L H H H H H L
: :
: :
: :
: :
MSB LSB G5 G 4 G3 G2 G1 G 0
: :
: :
: :
: :
MSB LSB B5 B4 B3 B2 B1 B0
: :
: :
: :
: :
Gray scale
L3…L60
L3…L60
L3…L60
L3…L60
level
-
-
-
-
-
-
-
­L0 L1 L2
L61 L62
L0 L1 L2
L61 L62
L0 L1 L2
L61 L62
L0 L1 L2
L61 L62
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
Document Title HSD173PUW1-A Formal Specification Page No. 12/27
Document No. Revision 1.0
5.0 INTERFACE PIN CONNECTION
5.1
TFT LCD Module
Pin No. Signal Description
1 COLOR_EN 2 VCC 3.3V Power Supply
3 VCC 3.3V Power Supply 4 V_EDID EDID 3.3V Power Supply
5 CABC_EN 6 CLK_EDID EDID Clock
7 DATA_EDID EDID Data 8 RxOIN0- -LVDS Differential Data Input (Odd R0-R5,G0) 9 RxOIN0+ +LVDS Differential Data Input (Odd R0-R5,G0)
10 GND Ground
11 RxOIN1- - LVDS differential data input(Odd G1-G5,B0-B1) 12 RxOIN1+ +LVDS differential data input(Odd G1-G5,B0-B1) 13 GND Ground 14 RxOIN2- - LVDS differential data input (Odd B2-B5,HS,VS,DE) 15 RxOIN2+ +LVDS differential data input (Odd B2-B5,HS,VS,DE) 16 GND Ground 17 RxOCLKIN- -LVDS differential clock input(Odd) 18 RxOCLKIN+ +LVDS differential clock input(Odd) 19 GND Ground 20 RxEIN0- - LVDS differential data input (Even R0-R5,G0) 21 RxEIN0+ +LVDS differential data input (Even R0-R5,G0) 22 GND Ground-Shield 23 RxEIN1- - LVDS differential data input (Even G1-G5,B0-B1) 24 RxEIN1+ +LVDS differential data input (Even G1-G5,B0-B1) 25 GND Ground-Shield 26 RxEIN2- - LVDS differential data input (Even B2-B5,HS,VS,DE) 27 RxEIN2+ +LVDS differential data input (Even B2-B5,HS,VS,DE) 28 GND Ground-Shield 29 RxECLKIN- -LVDS differential clock input(Even) 30 RxECLKIN+ +LVDS differential clock input(Even) 31 VLED_GND LED Ground 32 VLED_GND LED Ground 33 VLED_GND LED Ground 34 NC No Connection 35 PWM PWM Signal for LED dimming control 36 LED_EN LED Enable Pin (+3V Input) 37 NC No Connection 38 VLED LED Power Supply 7-21V 39 VLED LED Power Supply 7-21V 40 VLED LED Power Supply 7-21V
Note
The brightness of LCD panel could be changed by adjusting PWM
CN1 (Input signal): IPEX 20455-040E-12 (IPEX or equivalent)
Color Engine Enable Default 0 : Disable
CABC Enable Default 1 : Disable
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
Supply Voltage
3.0
v
td
Document Title HSD173PUW1-A Formal Specification Page No. 13/27
Document No. Revision 1.0
6.0 ELECTRICAL CHARACTERISTICS
6.1 TFT LCD Module Item Symbol
VDD 3.0 3.3 3.6 V Note (1)
Current of power supply
Inrush current
Note (1): V
When VDD operating within 2.7VVDD<3.0Vtd10ms , the display may
VDD<2.7V , VDD dip condition should also follow the Power On/Off
DD-
momentarily become abnormal.
conditions for supply voltage.
.
IDD - 0.4 - A VDD =3.3VL0 pattern
I
RUSH
dip condition:
Min. Typ. Max. Unit
- - 3.0 A Note (2)
Note
VDD
GND
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
V
V
Document Title HSD173PUW1-A Formal Specification Page No. 14/27
Document No. Revision 1.0
Note
(2) Power on Inrush current test circuit
0V
0.1VDD
rising time
in
0.9VDD
0.5 ms
DD
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
DE
2.5/7T
5.5/7T
Document Title HSD173PUW1-A Formal Specification Page No. 15/27
Document No. Revision 1.0
6.2 Switching Characteristics for LVDS Receiver
Item Symbol Min. Typ.
Max. Unit Conditions Differential Input High Threshold Vth Differential Input Low Threshold
Input Current Differential input Voltage
Common Mode Voltage Offset VCM (|VID|/2)
6.3 Bit Mapping & Interface Definition
7T
6.5/7T
4.5/7T
3.5/7T
1.5/7T
0.5/7T
RCLK
Rin0
R[2]
R[1]
R[0]
Vtl -100
I
IN
|VID|
G[0]
R[5]
-10
0.2
R[4]
1.2
2.25-(|VID|/2)
R[3]
100 mV
VCM=1.2V
mV
+10 uA
0.6 V V
R[2]
R[1]
R[0]
G[0]
Rin1
G[3]
G[2]
G[1]
B[1]
B[0]
G[5]
G[4]
G[3]
G[2]
Rin2
B[4]
B[3]
B[2] DE
(VS)
(HS)
B[5]
B[4]
B[3]
Pervious cycle Current cycle
LVDS Receiver Input Timing Definition
for 6bits LVDS input
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
G[1]
B[2]
B[1]
Next cycle
HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
(1)Vertical
X,1198
X,1200
X,1199
B
B
Document Title HSD173PUW1-A Formal Specification Page No. 16/27
Document No. Revision 1.0
6.4 Interface Timing (DE mode)
Item Symbol Frame Rate -- 55 60 65 Hz Frame Period t1 1088 1096 1104 line Vertical Display Time t2 1080 1080 1080 line Vertical Blanking Time t3 8 16 24 line 1 Line Scanning Time t4 1000 1008 1184 clock Horizontal Display Time t5 960 960 960 clock Horizontal Blanking Time
t6 40 48 224 clock
Clock Rate t7 59.85 66.30 85.00 MHz
Timing Diagram of Interface Signal (DE mode)
Min. Typ. Max. Unit
NCLK
DE
R
0~5
R
0~7
G
0~5
G
0~7
B
0~5
(2)Horizontal
NCLK
DE
R
0~5
R
0~7
G
0~5
G
0~7
B
0~5
t2
t4
X,1 X,2 X,3 X,Y
t7
1234567891011
t1
X 1078
X 1079
X 1080
t4
t5 t6
1911
1913
1915
1917
12
1912
1914
1916
1918
1919 1920
t3
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
0.9V
DD
0.6
V 0.6
V
50%
Document Title HSD173PUW1-A Formal Specification Page No. 17/27
Document No. Revision 1.0
6.5 Power On / Off Sequence
Power Supply
0V
0V
(Recommended
0.1V
DD
Signal
Backlight
Item Min. Typ. Max. Unit Remark TP1 0.5 -- 10 msec TP2 0.01 -- 50 msec TP3 20 35 50 msec TP4 1000 -- -- msec TP5 200 -- -- msec TP6 200 -- -- msec
Power On
TP1
TP2
)
TP5
TP6
50
%
Power
TP3
Off
0.9V
D
D
0.1V
DD
TP
4
0.1V
DD
Note
(1) The supply voltage of the external system for the module input should be the same
as the definition of VDD.
(2) Apply the lamp volatge within the LCD operation range. When the back-light turns
on before the LCD operation or the LCD truns off before the back-light turns off, the
display may momentarily become white.
(3) In case of VDD = off level, please keep the level of input signal on the low or
keep a high impedance.
(4) TP4 should be measured after the module has been fully discharged between
power off and on period.
(5) Interface signal shall not be kept at high impedance when the power is on.
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
Document Title HSD173PUW1-A Formal Specification Page No. 18/27
Document No. Revision 1.0
6.6 Backlight Unit Parameter Symbol Min Typ Max Units Condition
LED Current IF -- 20 20.6 mA LED Voltage VF 3.0 3.2 3.4 Volt LED Power
P
--
LED
4.61 5.05
Watt
consumption LED Life-Time N/A 10,000 -- -- Hour
Ta=25 Ta=25 Ta=25
Note (1) Ta=25 IF=20mA
Note (2)
Note (1): Calculator value for reference P=IF x VF x N (LED Qty’)
Note (2): The LED lifetime defines as the estimated time to 50% degradation of final
luminous.
6.7 LED Driver
6.7.1 Absolute Maximum Ratings
Item Symbol Min. Max. Unit Note
LED Power Supply voltage LED_EN, PWM pin Voltage
V
LED
VEN, V
-0.3 24 Volt
PWM
-- 3.6 Volt
6.7.2 DC Electrical Characteristics Parameter Symbol Min Typ Max Units
LED Power
V
LED
7.0 -- 21.0 Volt
Supply Voltage
LED_EN High Threshold
LED_EN Low Threshold
PWM High Threshold
PWM Low Threshold
PWM Frequency PWM Duty Cycle
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
V
V
V
PWMH
V
PWML
F
ENH
ENL
PWM
T
D
2.0 -- -- Volt
-- -- 0.3 Volt
3.0 -- -- Volt
-- -- 0.2 Volt
225
275
Hz
250
10 -- 100 %
HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
Dimming
Signal
, PWM
LED Enable
, LED_EN
0.9V
0.9V
T3
T
t
Document Title HSD173PUW1-A Formal Specification Page No. 19/27
Document No. Revision 1.0
Duty Cycle TD= (t / T) x 100%
6.7.3 LED Power on/off sequence
LED Power Supply, V
LED
T1 T2 T4 T5
0.1V
0V
LED
0.1V
LED
0V
0V
Symbol
T1 T2 T3 T4 T5
Min Typ Max
10 -- -­10 -- -­50 -- --
0 -- --
10 -- --
Note (1): The duty of LED dimming signal should be more than 20% in T2 and T3
Note (2): PWM can adjust brightness to control Pin. Pulse duty the bigger the brighter.
Value
Unit
ms
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
CABC_EN High
Document Title HSD173PUW1-A Formal Specification Page No. 20/27
Document No. Revision 1.0
6.8 Color Engine and CABC DC Electrical Characteristics
Parameter Symbol
Min Typ Max Units Remark
COLOR_EN High Threshold
COLOR_EN Low Threshold
Threshold CABC_EN Low
Threshold
V
COLH
V
COLL
V
CABCH
V
CABCL
0.7V
DD
-- -- 0.3V
0.7V
DD
-- -- 0.3V
-- -- Volt
DD
Volt
-- -- Volt
DD
Volt
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
C(30min),100 cycles
100
20 40
50
Document Title HSD173PUW1-A Formal Specification Page No. 21/27
Document No. Revision 1.0
7.0 Reliability test items
No.
1 High Temperature Storage Ta=+60oC, 240hrs 2 Low Temperature Storage Ta=-20oC, 240hrs
High Temperature Operation Ta=+50oC, 500hrs
3
Low Temperature Operation Ta=0oC, 500hrs
4 5 Thermal Cycling Test (non operation) -20oC(30min)+60
Vibration
6
7 Shock
Storage / Operating temperature
Note .Max wet bulb temp.=39oC
Item Conditions Remark
o
Sine Wave
1.5G, 5~500Hz, XYZ 30min/each direction Half-Sine, 200G, 2ms, ±XYZ, 1time
-40
Humidity (%)
-20
90
80
60
40
Storage Range
20
10
0
0
Temperature (oC)
Operating Range
60
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
Document Title HSD173PUW1-A Formal Specification Page No. 22/27
Document No. Revision 1.0
8.0 OUTLINE DIMENSION
8.1 Front View Outline Dimension
nit : mm
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
+0.5
BTC 0
-0
HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
Document Title HSD173PUW1-A Formal Specification Page No. 23/27
Document No. Revision 1.0
8.2 Back View Outline Dimension
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Document Title HSD173PUW1-A Formal Specification Page No. 24/27
Document No. Revision 1.0
9.0 LOT MARK
9.1 Lot Mark
1
Code 1,2,3,4,5,6: HannStar internal flow control code. Code 7: production location. Code 8: production year. Code 9: production month. Code 10,11,12,13,14,15: serial number.
Note (1) Production Year
Year 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010
Mark 1 2 3 4 5 6 7 8 9 0
Note (2) Production Month
Month Jan. Feb. Mar. Apr. May. Jun. Jul. Aug. Sep. Oct Nov. Dec.
Mark 1 2 3 4 5 6 7 8 9 A B C
9.2 Location of Lot Mark
(1) The label is attached to the backside of the LCD module. (2) This is subject to change without prior notice.
HSD173PUW1 Rev: * -A EDX.X 6 A0
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
Document Title HSD173PUW1-A Formal Specification Page No. 25/27
Document No. Revision 1.0
10.0 PACKAGE SPECIFICATION
10.1 Packing form
LCM Model LCM Qty. in the box
HSD173PUW1-A
35 pcs/box
10.2 Packing assembly drawings
Inner Box Size
556 x 318 x 500
(mm)
H
Notice
HSD173PHW1-A Material Notice
Box Corrugated Paper Board
Partition/Pad Corrugated Paper Board
Corner Pad Corrugated Paper Board
ESD bag PE --
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
(AB Flute)
(B Flute)
(AB Flute)
HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
Document Title HSD173PUW1-A Formal Specification Page No. 26/27
Document No. Revision 1.0
11.0 GENERAL PRECAUTION
11.1 Use Restriction
This product is not authorized for use in life supporting systems, aircraft navigation control systems, military systems and any other application where performance failure could be life-threatening or otherwise catastrophic.
11.2 Disassembling or Modification
Do not disassemble or modify the module. It may damage sensitive parts inside LCD module, and may cause scratches or dust on the display. HannStar does not warrant the module, if customers disassemble or modify the module.
11.3 Breakage of LCD Panel
11.3.1.If LCD panel is broken and liquid crystal spills out, do not ingest or inhale liquid crystal, and do not contact liquid crystal with skin.
11.3.2. If liquid crystal contacts mouth or eyes, rinse out with water immediately.
11.3.3. If liquid crystal contacts skin or cloths, wash it off immediately with alcohol and
rinse thoroughly with water.
11.3.4. Handle carefully with chips of glass that may cause injury, when the glass is
broken.
11.4 Electric Shock
11.4.1. Disconnect power supply before handling LCD module.
11.4.2. Do not pull or fold the LED cable.
11.4.3. Do not touch the parts inside LCD modules and the fluorescent LED’s connector
or cables in order to prevent electric shock.
11.5 Absolute Maximum Ratings and Power Protection Circuit
11.5.1. Do not exceed the absolute maximum rating values, such as the supply voltage variation, input voltage variation, variation in parts’ parameters, environmental temperature, etc., otherwise LCD module may be damaged.
11.5.2. Please do not leave LCD module in the environment of high humidity and high temperature for a long time.
11.5.3. It’s recommended to employ protection circuit for power supply.
11.6 Operation
11.6.1 Do not touch, push or rub the polarizer with anything harder than HB pencil lead.
11.6.2 Use fingerstalls of soft gloves in order to keep clean display quality, when persons handle the LCD module for incoming inspection or assembly.
11.6.3 When the surface is dusty, please wipe gently with absorbent cotton or other soft material.
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
of HannStar Display Corporation. It shall not be disclosed,
Document Title HSD173PUW1-A Formal Specification Page No. 27/27
Document No. Revision 1.0
11.6.4 Wipe off saliva or water drops as soon as possible. If saliva or water drops contact with polarizer for a long time, they may causes deformation or color fading.
11.6.5 When cleaning the adhesives, please use absorbent cotton wetted with a little petroleum benzine or other adequate solvent.
11.7 Mechanism
Please mount LCD module by using mounting holes arranged in four corners tightly.
11.8 Static Electricity
11.8.1 Protection film must remove very slowly from the surface of LCD module to
prevent from electrostatic occurrence.
11.8.2 Because LCD module use CMOS-IC on circuit board and TFT-LCD panel, it is very weak to electrostatic discharge. Please be careful with electrostatic discharge. Persons who handle the module should be grounded through adequate methods.
11.9 Strong Light Exposure The module shall not be exposed under strong light such as direct sunlight. Otherwise,
display characteristics may be changed.
11.10 Disposal
When disposing LCD module, obey the local environmental regulations.
The information contained in this document is the exclusive property distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Loading...