Note : 1. The information contained herein is preliminary and may be changed without prior notices.
2. Please contact HannStar Display Corp. before designing your product based on this module
specification.
3. The information contained herein is presented merely to indicate the characteristics and performance
of our products. No responsibility is assumed by HannStar for any intellectual property claims or other
problems that may result from application based on the module described herein.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
1.0---Oct. 14, 2002HSD150SX84-C Specifictaion was first issued.
Record of Revisions
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
HannStar Display model HSD150SX84-C is a color active matrix thin film transistor
(TFT) liquid crystal display (LCD) that uses amorphous silicon TFT as a switching device.
This model is composed of a TFT LCD panel, the voltage reference, common voltage,
DC-DC converter, column, and row driver circuit. This TFT LCD has a 15-inch diagonally
measured active display area with XGA resolution (768 vertical by 1024 horizontal pixel
array).
1.2 Features
¦ 15” XGA TFT LCD panel
¦ 2 CCFLs Backlight system
¦ Supported XGA (V:768 lines, H:1024 pixels) resolution
¦ Supported to 75Hz refresh rate
¦ Without LCD Timing Controller
1.3 General information
ItemSpecificationUnit
Outline dimension321.0×249.0×10.5 (typ.)mm
Display area304.1(H) x 228.1(V) (15.0” diagonal)mm
Number of Pixel1024(H) x 768(V)pixels
Pixel pitch0.297(H) x 0.297(V)mm
Pixel arrangementRGB Vertical stripe
Display color6-bits driver
Display modeNormally white
Surface treatmentAntiglare, Hard-Coating(3H)
Weight(950) (typ.)g
Back-light2-CCFLs, Top & bottom edge side
Input signalSource and Gate Driver control signals
Power consumption11.0(typ.),W
Optimum viewing
direction
6 o’clock
1.4 Applications
¦ Desktop monitors
¦ Display terminals for AV applications
¦ Monitors for industrial applications
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Note: (1) Permanent damage may occur to the LCD module if beyond this specification.
Functional operation should be restricted to the conditions described under
02000V(rms)(1)
-
7.0mA(1)
0100KHz(1)
Normal Operating Conditions.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Note (3) Definition of Response Time: Sum of TR and T
white(TFT OFF)black(TFT ON)white(TFT OFF)
T
R
100%
90%
Optical
response
10%
0%
Note (4) Optical characteristic measurement setup
F
T
F
Photo-detector (BM-5A)
time
Field=2
o
50cm
LCD panel
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Luminance uniformity =(Min Luminance)/(Max Luminance) x 100%
1
V
4
V
1
V
2
1
V
4
1
H
4
1
H
2
H
1
4
Display center
H
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
R G B R G B R G B R G B R G B R G BR G B
R G B R G B R G B R G B R G BR G B
R G B R G B R G B R G BR G B
R G B R G B R G BR G B
R G B R G BR G B
R G BR G B
R G B R G B R G B R G B R G B
R G B R G B R G B
R G B R G B R G B R G B
R G B
R G B R G B
LCD Display Area
1 Pixel =
R G B R G B R G B R G B R G B R G BR G B
1024 Pixels
R G B
768 Lines
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
4.3 Relationship between Displayed Color and Input Data
Basic
color
Gray
scale
of
Red
Gray
scale
of
Green
Gray
scale
of
Blue
Gray
scale
of
White
and
Black
Display
Black
BlueLLLLLLLLLLLLHHHHHH-
Green
Light Blue LLLLLLHHHHHHHHHHHH-
RedHHHHHHLLLLLLLLLLLL -
PurpleHHHHHHLLLLLLHHHHHH-
YellowHHHHHHHHHHHHLLLLLL -
WhiteHHHHHHHHHHHHHHHHHH-
BlackLLLLLLLLLLLLLLLLLL L0
Dark
Light
RedHHHHHHLLLLLLLLLLLLRed L63
Black
Dark
Light
GreenLLLLLLHHHHHHLLLLLLGreen L63
BlackLLLLLLLLLLLLLLLLLL L0
Dark
Light
Blue
BlackLLLLLLLLLLLLLLLLLL L0
Dark
Light
WhiteHHHHHHHHHHHHHHHHHHWhite L63
MSB LSB
R5 R4 R3 R2 R1 R0
LLLLLHLLLLLLLLLLLL L1
LLLLHLLLLLLLLLLLLL L2
?
?
HHHHLHLLLLLLLLLLLL L61
HHHHHLLLLLLLLLLLLL L62
LLLLLLLLLLLHLLLLLL L1
LLLLLLLLLLHLLLLLLL L2
?
?
LLLLLLHHHHLHLLLLLL L61
LLLLLLHHHHHLLLLLLL L62
LLLLLLLLLLLLLLLLLH L1
LLLLLLLLLLLLLLLLHL L2
?
?
LLLLLLLLLLLLHHHHHL L62
LLLLLHLLLLLHLLLLLH L1
LLLLHLLLLLHLLLLLHL L2
?
?
HHHHLHHHHHLHHHHHLH L61
HHHHHLHHHHHLHHHHHL L62
:
:
:
:
:
:
:
:
MSB LSB
G5 G4 G3 G2G1 G0
:
:
:
:
:
:
:
:
MSB LSB
B5 B4 B3 B2 B1 B0
:
:
:
:
:
:
:
:
Gray scale
level
L3… L60
L3… L60
L3… L60
L61
Blue L63
L3… L60
-
-
L0
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
5.1 Interface FPC Connector (40-pins x 2) (Hirose: FH12-40S-0.5SH)
I/F FRC Connector (J1)I/F FRC Connector (J2)
Pin
SymbolDescription
No.
1
NCNo Connecting
2 NCNo Connecting2 VDDDigital Power Input (DC +3.3V)
3 GNDGround3 GNDGround
4 GNDGround4 GNDGround
5 EB5Even-dot Blue Data bit 5 (MSB)5 OB5Odd-dot Blue Data bit 5 (MSB)
6
EB4Even-dot Blue Data bit 4
7 EB3Even-dot Blue Data bit 37 OB3Odd-dot Blue Data bit 3
8 EB2Even-dot Blue Data bit 28 OB2Odd-dot Blue Data bit 2
9 EB1Even-dot Blue Data bit 19 OB1Odd-dot Blue Data bit 1
10 EB0Even-dot Blue Data bit 0 (LSB)10 OB0Odd-dot Blue Data bit 0 (LSB)
11
GNDGround
12 EG5Even-dot Green Data bit 5 (MSB)12 OG5Odd-dot Green Data bit 5 (MSB)
13 EG4Even-dot Green Data bit 413 OG4Odd-dot Green Data bit 4
14 EG3Even-dot Green Data bit 314 OG3Odd-dot Green Data bit 3
15 EG2Even-dot Green Data bit 215 OG2Odd-dot Green Data bit 2
16
EG1Even-dot Green Data bit 1
17 EG0Even-dot Green Data bit 0 (LSB)17 OG0Odd-dot Green Data bit 0 (LSB)
18 GNDGround18 GNDGround
19 ER5Even-dot Red Data bit 5 (MSB)19 OR5Odd-dot Red Data bit 5 (MSB)
20 ER4Even-dot Red Data bit 420 OR4Odd-dot Red Data bit 4
21
ER3Even-dot Red Data bit 3
22 ER2Even-dot Red Data bit 222 OR2Odd-dot Red Data bit 2
23 ER1Even-dot Red Data bit 123 OR1Odd-dot Red Data bit 1
24 ER0Even-dot Red Data bit 0 (LSB)24 OR0Odd-dot Red Data bit 0 (LSB)
25 GNDGround25 GNDGround
26
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Mating connector: SM02 (8.0)B-BHS-1/ Japan Solderless Terminal MFG Co., LTD
Terminal No.SymbolFunction
1VLCCFL power supply (high voltage)
2NC
3GLCCFL power supply (low voltage)
Note 1) Please connects NC pin to nothing. Don’t connect it to ground nor to other signal
Input. (NC pin should be open.)
1)
No connection
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
The backlight system is an edge-lighting type with 2-CCFL (Cold Cathode Fluorescent Lamp).
The characteristics of four lamps are shown in the following tables.
ItemSymbolMin.Typ.Max.UnitNote
Lamp currentI
Lamp voltageV
L
L
3.06.07.0mA(rms)(1)
684760
-
V(rms)IL=6.0 mA
Frequencyf
L
405580KHz(2)
CCFL life timeHr30,000--Hour(3)
1150at 25oC
Startup voltageVs
1350
--V(rms)
at 0oC
* Inrush current conditions
3.3V
t=400us ~ 10ms(or 1ms)
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Note: (1) Lamp current is measured with current meter for high frequency as shown below. Specified
values are for a lamp.
LCD MODULE
2
3
INVERTER
(HIU-757)
2
3
(2) Lamp frequency may produce interference with horizontal synchronous frequency and this
may cause line flow on the display. Therefore lamp frequency shall be detached from the
horizontal synchronous frequency and its harmonics as far as possible in order to avoid
interference.
(3) Life time (Hr) can be defined as the time in which it continues to operate under the condition:
Temp. =25±3ºC , IL=6.0mA(rms.) and fL=50 KHz until one of the following event occurs:
1.When the brightness becomes 50%.
2.When the startup voltage (Vs) at 0ºC becomes higher than the maximal value of Vs
specified above.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Note 1) Refer to VESA standard.
Note 2) In case of using the long frame period, the deterioration of display quality, noise etc. may be
occurred.
Note 3) Do not fix CPH1 and CPH2 to “H” or “L” level while the VDD (+3.3V) is supplied. If CPH1
and CPH2 is fixed to “H” level or “L” level for certain period while the VDD (+3.3V) is
supplied, the panel may be damaged.
Note 4) Do not change t3 and t6 values in the operation. When t1 or t4 is changed, the panel is
displayed as black.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Note 5) Please adjust LCD operating signal timing and FL driving frequency, to optimize the display
quality. There is a possibility that flicker is observed by the interference of LCD operating
signal timing and FL driving condition (especially driving frequency).
Note 6) All of the timing have to meet “ 6.3.1 AC timing chart – Pixel frequency must less than 40
MHz“ , frame rate 85Hz can be acceptable.
Note 7) All of the timing setting should be confirmed by Hannstar’s FAE.
6.3.2 AC Timing Charts:
(1). Reference Signal (pixel clock):
Reference Signal
(Pixel Clock)
Input Clock
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Note:(1) The supply voltage of the external system for the module input should be the same as the
definition of VDD.
(2) Apply the lamp volatge within the LCD operation range. When the back-light turns on
before the LCD operation or the LCD truns off before the back-light turns off, the display
may momentarily become white.
(3) In case of VDD = off level, please keep the level of input signal on the low or keep a high
impedance.
(4) T4 should be measured after the module has been fully discharged between power off and
on period.
(5)Interface signal shall not be kept at high impedance when the power is on.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
7.1.3 Tolerance of distance between active area and bezel opening
∣a-b∣≦ 1mm
∣c-d∣≦ 1mm
LCD
c
ab
d
Active area
Bezel opening
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
code 1,2,3,4,5,6: HannStar internal flow control code.
code 7: production location.
code 8: production year.
code 9: production month.
code 10,11,12,13,14,15: serial number.
(1) The label is attached to the backside of the LCD module.
(2) This is subject to change without prior notice.
101112131415
HSD150SX84
-C
Rev:
Lot mark
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
(1) package quantity in one carton: 10 pieces.
(2) carton size: 453±3 mm×360±3 mm×403±3 mm.
(3) for domestic transportation only.
9.2 packing assembly drawings
LCD Module
Bag
Packing pair
Packing pair
Packing plate
Packing plate
Bag
Tape
One packing
Packing plate
Tape
Carton
Carton
One carton contents of 5 packing pairs (Total 10 pieces)
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
This product is not authorized for use in life supporting systems, aircraft navigation control
systems, military systems and any other application where performance failure could be
life-threatening or otherwise catastrophic.
10.2 Disassembling or Modification
Do not disassemble or modify the module. It may damage sensitive parts inside LCD
module, and may cause scratches or dust on the display. HannStar does not warrant the
module, if customer s disassemble or modify the module.
10.3 Breakage of LCD Panel
10.3.1 If LCD panel is broken and liquid crystal spills out, do not ingest or inhale liquid
crystal, and do not contact liquid crystal with skin.
10.3.2 If liquid crystal contacts mouth or eyes, rinse out with water immediately.
10.3.3 If liquid crystal contacts skin or cloths, wash it off immediately with alcohol and
rinse thoroughly with water.
10.3.4 Handle carefully with chips of glass that may cause injury , when the glass is
broken.
10.4 Electric Shock
10.4.1 Disconnect power supply before handling LCD module.
10.4.2 Do not pull or fold the CCFL cable.
10.4.3 Do not touch the parts inside LCD modules and the fluorescent lamp’s connector
or cables in order to prevent electric shock.
10.5 Absolute Maximum Ratings and Power Protection Circuit
10.5.1 Do not exceed the absolute maximum rating values, such as the supply voltage
variation, input voltage variation, variation in parts’ parameters, environmental
temperature, etc., otherwise LCD module may be damaged.
10.5.2 Please do not leave LCD module in the environment of high humidity and high
temperature for a long time.
10.5.3 It’s recommended employing protection circuit for power supply.
10.6 Operation
10.6.1 Do not touch, push or rub the polarizer with anything harder than HB pencil lead.
10.6.2 Use fingerstalls of soft gloves in order to keep clean display quality, when persons
handle the LCD module for incoming inspection or assembly.
10.6.3 When the surface is dusty, please wipe gently with absorbent cotton or other soft
material.
10.6.4 Wipe off saliva or water drops as soon as possible. If saliva or water drops contact
with polarizer for a long time, they may causes deformation or color fading.
10.6.5 When cleaning the adhesives, please use absorbent cotton wetted with a little
petroleum benzine or other adequate solvent.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Please mount LCD module by using mounting holes arranged in both sides tightly.
Torque :3 kgf/ cm
10.8 Static Electricity
10.8.1 Protection film must remove very slowly from the surface of LCD module to
prevent from electrostatic occurrence.
10.8.2 Because LCD module uses CMOS-IC on circuit board and TFT-LCD panel, it is
very weak to electrostatic discharge. Please be careful with electrostatic discharge.
10.8.3 Persons who handle the module should be grounded through adequate methods.
10.9 Strong Light Exposure
The module shall not be exposed under strong light such as direct sunlight. Otherwise,
display characteristics may be changed.
10.10 Disposal
When disposing LCD module, obey the local environmental regulations.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.