HannStar Display Corp.
Document Title
Document No. Revision 1.0
TO :
HSD101PFW1 Specification
Page No. 1/26
Date : SEP., 14, 2010
Customer Acceptance Specification
Model: HSD101PFW1
www.jxlcd.com
www.jxlcd.com
Accepted by:
Proposed by: Technical Service Division
Signature Date
-B00
Signature Date
Note:
(1) Please contact HannStar Display Corp. before designing your product based on
this module specification.
(2) The information contained herein is presented merely to indicate the characteristics and
performance of our products. No responsibility is assumed by HannStar for any
intellectual property claims or other problems that may result from application based on
the module described herein.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed,
distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
Document Title
Document No. Revision 1.0
HSD101PFW1 Specification
Page No. 2/26
Record of Revisions
Rev. Date Sub-Model
1.0
Sep. 14, 2010
B00
www.jxlcd.com
www.jxlcd.com
Description of change
Customer Acceptance Specification of HSD101PFW1 was 1
released
st
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed,
distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
Document Title
Document No. Revision 1.0
1.0 General description ………………………………… p.4
2.0 Absolute maximum ratings……………………………. p.5
3.0 Optical characteristics.………………………………. p.6
4.0 Block diagram ……………………………………… p.10
5.0 Interface pin connection …………………………… p.12
6.0 Electrical characteristics …………………………… p.13
HSD101PFW1 Specification
Contents
Page No. 3/26
7.0 Reliability test items ………………………………… p.20
8.0 Outline dimension …………………………………… p.21
9.0 Lot mark ……………………………………………... p.23
10.0 Package specification ……………………………… p.24
www.jxlcd.com
11.0 General precaution …………………………………… p.25
www.jxlcd.com
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed,
distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
Document Title
Document No. Revision 1.0
1.0 GENERAL DESCRIPTION
1.1 Introduction
HannStar Display model HSD101PFW1-B is a color active matrix thin film
transistor (TFT) liquid crystal display (LCD) that uses amorphous silicon TFT as a
switching device. This model is composed of a TFT LCD panel, a driving circuit
and a back light system. This TFT LCD has a 10.1 (16:9) inch diagonally
measured active display area with WSVGA (1024 horizontal by 576 vertical pixel)
resolution.
1.2 Features
■ 10.1 (16:9 diagonal) inch configuration
■ One channel LVDS interface
■ 262K color by 6 bit R.G.B signal input
■ RoHS Compliance
■ Halogen Free
1.3 Applications
Mobile NB
Digital Photo frame
Display terminal for AV application
1.4 General information
www.jxlcd.com
www.jxlcd.com
Outline Dimension 235 x 143 x 4.9 (Typ.) mm
Display area 222.72(H) x 125.28(V) mm
Number of Pixel 1024 RGB (H) x 576(V) pixels
Pixel pitch 0.2175(H) x 0.2175(V) mm
Pixel arrangement RGB Vertical stripe
Display mode Normally white
NTSC 50 %
Surface treatment Glare, Hard-Coating (3H)
Weight 190 (Typ.) g
Back-light White LED
Power
Consumption
HSD101PFW1 Specification
Item Specification Unit
Logic System 1.0 (Max.) W
B/L System 2.3 (Max.) W
Page No. 4/26
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed,
distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
Document Title
Document No. Revision 1.0
1.5 Mechanical Information
Module
Size
Weight
2.0 ABSOLUTE MAXIMUM RATINGS
2.1 Electrical Absolute Rating
2.1.1 TFT LCD Module
Logic Supply voltage
2.1.2 Environment Absolute Rating
Operating Temperature T
Storage Temperature T
www.jxlcd.com
www.jxlcd.com
HSD101PFW1 Specification
Item Min. Typ. Max. Unit
Horizontal (H) 234.5 235 235.5 mm
Vertical (V) 142.5 143 143.5 mm
Depth (D)
Item Symbol Min. Max. Unit Note
VDD -0.3 4.0 V
Item Symbol Min. Max. Unit Note
－
－
0 50
opa
-20 60
stg
4.9
190 200 g
Page No. 5/26
5.2 mm
℃
℃
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed,
distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
Document Title
Document No. Revision 1.0
HSD101PFW1 Specification
Page No. 6/26
3.0 OPTICAL CHARACTERISTICS
3.1 Optical specification
Item Symbol Condition Min. Typ. Max. Unit Note
－
Contrast CR
Tr
Response time
Tf
400 500
－
－
2 4
6 12
(1)(2)(4)
msec
(1)(3)
White luminance
(5 point)
Red
Color
chromaticity
(CIE1931)
www.jxlcd.com
www.jxlcd.com
Viewing angle
Brightness uniformity B
Brightness Uniformity B
3.2 Measuring Condition
■ Measuring surrounding：dark room
■ LED current I
■ Ambient temperature：25±2oC
■ 15min. warm-up time.
Green
Blue
White
Hor.
Ver.
160 200
Y
L
Rx
R
Y
Gx
G
Y
Bx
B
Y
Wx
Wy
Θ
L
Θ
R
Θ
U
Θ
D
UNI
UNI
：
20mA / signal LED
L
Normal
viewing
CR>10
(5point)
(13 points)
Θ=0
angle
Θ
Θ
=0
=0
0.581
0.336
0.330
0.545
0.123
0.089
0.283
0.299
40
40
10
30
80
70
－
0.611 0.641
0.366 0.396
0.360 0.390
0.575 0.605
0.153 0.183
0.119 0.149
0.313 0.343
0.329 0.359
－
－
－
－
－
－
45
45
15
35
－
－
cd/m
(1)(4)
(IL=20mA)
% (5)
% (6)
(1)(4)(5)
2
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed,
distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
Document Title
Document No. Revision 1.0
3.3 Measuring Equipment
■ FPM520 of Westar Display technologies, INC., which utilized SR-3 for Chromaticity
and BM-5A for other optical characteristics.
■ Measuring spot size：20 ~ 21 mm
Note (1) Definition of Viewing Angle:
Note (2) Definition of Contrast Ratio (CR) :
measured at the center point of panel
Luminance with all pixels white
CR =
Luminance with all pixels black
www.jxlcd.com
www.jxlcd.com
HSD101PFW1 Specification
Θ
L
Φ=180o
Θ
D
6’ o’clock
Φ=270
Θ
U
12’ o’clock
Φ=90
Θ
o
o
R
Page No. 7/26
Φ=0o
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed,
distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
Document Title
Document No. Revision 1.0
Note (3) Definition of Response Time : Sum of TR and TF
Optical
response
Note (4) Definition of optical measurement setup
www.jxlcd.com
www.jxlcd.com
HSD101PFW1 Specification
white(TFT OFF) black (TFT ON) white(TFT OFF)
T
R
100%
90%
10%
0%
Page No. 8/26
T
F
time
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed,
distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
Document Title
Document No. Revision 1.0
Note (5) Definition of Average Luminance Uniformity of White (5 Point)
HSD101PFW1 Specification
Page No. 9/26
Average Luminance Uniformity =
www.jxlcd.com
www.jxlcd.com
Y1+Y2+Y3+Y4+Y5
5
Note (6) Definition of brightness uniformity
Luminance uniformity(13points) = ×100%
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed,
distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Luminance uniformity(5 points) = ×100%
(Min Luminance of 5 points)
(Max Luminance of 5 points)
(Min Luminance of 13 points)
(Max Luminance of 13 points)
HannStar Display Corp.
R
Document Title
Document No. Revision 1.0
HSD101PFW1 Specification
Page No. 10/26
4.0 BLOCK DIAGRAM
4.1 TFT LCD Module:
LED
Driver
Timing
X-driver IC
Connector
EDID
DC/DC
Converter
Controller
+
LVDS
Receiver
Liquid Crystal Panel
Y-driver IC
1024x576 pixels
www.jxlcd.com
www.jxlcd.com
4.2 Pixel Format
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed,
distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
1,1
2,1
576,1
1,2 1,3 1,4
Gray scale
Manipulation
Voltage
Generation
Circuit
1024 pixel (3072 Dots)
LCD Display Area
1 Pixel
R
B G
R
1,1024
576,
1024
576 Lines
HannStar Display Corp.
scale of
Document Title
HSD101PFW1 Specification
Page No. 11/26
Document No. Revision 1.0
4.3 Relationship Between Displayed Color and Input
Basic
color
Gray
scale
of Red
Gray
scale of
Green
Gray
scale of
Blue
Gray
White &
Black
MSB LSB
Display
Black L L L L L L L L L L L L L L L L L L -
Blue L L L L L L L L L L L L H H H H H H -
Green L L L L L L H H H H H H L L L L L L -
Light Blue L L L L L L H H H H H H H H H H H H -
Red H H H H H H L L L L L L L L L L L L Purple H H H H H H L L L L L L H H H H H H Yellow H H H H H H H H H H H H L L L L L L -
White H H H H H H H H H H H H H H H H H H -
Black L L L L L L L L L L L L L L L L L L L0
Dark
Light
Red H H H H H H L L L L L L L L L L L L Red L63
Black L L L L L L L L L L L L L L L L L L L0
Dark
www.jxlcd.com
Light
Green L L L L L L H H H H H H L L L L L L Green L63
Black L L L L L L L L L L L L L L L L L L L0
Dark
Light
Blue L L L L L L L L L L L L H H H H H H Blue L63
Black L L L L L L L L L L L L L L L L L L L0
Dark
Light
White H H H H H H
R5 R4 R3 R2 R1 R0
L L L L L H L L L L L L L L L L L L L1
L L L L H L L L L L L L L L L L L L L2
↑
↓
H H H H L H L L L L L L L L L L L L L61
H H H H H L L L L L L L L L L L L L L62
L L L L L L L L L L L H L L L L L L L1
L L L L L L L L L L H L L L L L L L L2
↑
www.jxlcd.com
↓
L L L L L L H H H H L H L L L L L L L61
L L L L L L
L L L L L L L L L L L L L L L L L H L1
L L L L L L L L L L L L L L L L H L L2
↑
↓
L L L L L L L L L L L L H H H H L H L61
L L L L L L
L L L L L H L L L L L H L L L L L H L1
L L L L H L L L L L H L L L L L H L L2
↑
↓
H H H H L H H H H H L H H H H H L H L61
H H H H H L
:
:
:
:
:
:
:
:
MSB LSB
G5 G 4 G3 G2 G1 G 0
:
:
:
:
H H H H H L L L L L L L L62
:
:
L L L L L L H H H H H L L62
:
:
H H H H H L H H H H H L L62
H H H H H H H H H H H H White L63
MSB LSB
B5 B4 B3 B2 B1 B0
:
:
:
:
:
:
:
:
Gray scale
level
L3…L60
L3…L60
L3…L60
L3…L60
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed,
distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
Document Title
Document No. Revision 1.0
5.0 INTERFACE PIN CONNECTION
5.1
TFT LCD Module
www.jxlcd.com
www.jxlcd.com
Note
HSD101PFW1 Specification
：
CN1 (Input signal): IPEX 20455-040E-12 (IPEX or equivalent)
：
：：
Pin No. Signal Description
1 NC No connection
2 VCC 3.3V Power Supply
3 VCC 3.3V Power Supply
4 V_EDID EDID 3.3V Power Supply
5 NC No Connection
6 CLK_EDID EDID Clock
7 DATA_EDID EDID Data
8 RXIN0- LVDS Signal - channel0-
9 RXIN0+ LVDS Signal+ channel0+
10 GND Ground
11 RXIN1- Data Input channel112 RXIN1+ Data Input channel1+
13 GND Ground
14 RXIN2- Data Input channel215 RXIN2+ Data Input channel2+
16 GND Ground
17 RXCLKIN- Data Input CLK18 RXCLKIN+ Data Input CLK+
19 GND Ground
20 NC No Connection
21 NC No Connection
22 GND Ground
23 NC No Connection
24 NC No Connection
25 GND Ground
26 NC No Connection
27 NC No Connection
28 GND Ground
29 NC No Connection
30 NC No Connection
31 VLED_GND LED Ground
32 VLED_GND LED Ground
33 VLED_GND LED Ground
34 NC No Connection
35 PWM PWM Signal for LED dimming control
36 LED_EN LED Enable Pin (+3V Input)
37 NC No Connection
38 VLED LED Power Supply 5-21V
39 VLED LED Power Supply 5-21V
40 VLED LED Power Supply 5-21V
：
The brightness of LCD panel could be changed by adjusting PWM
：
：：
Page No. 12/26
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed,
distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
3.0v td
Document Title
Document No. Revision 1.0
6.0 ELECTRICAL CHARACTERISTICS
6.1 TFT LCD Module
Supply Voltage VDD 3.0 3.3 3.6 V Note (1)
Current of
power supply
Inrush current
Note (1): V
When VDD operating within 2.7V≦VDD<3.0V，td≦10ms , the display may
HSD101PFW1 Specification
Item Symbol Min. Typ. Max. Unit
IDD - 0.266 0.303 A
I
- - 1.50 A Note (2)
RUSH
dip condition:
DD-
momentarily become abnormal.
VDD<2.7V , VDD dip condition should also follow the Power On/Off
conditions for supply voltage.
Page No. 13/26
Note
=3.3V、L0 pattern
V
DD
Ta=25℃ fv=60Hz
VDD
www.jxlcd.com
www.jxlcd.com
GND
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed,
distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
Document Title
Document No. Revision 1.0
Note
www.jxlcd.com
www.jxlcd.com
HSD101PFW1 Specification
：：：：
(2) Power on Inrush current test circuit
12v
0.1VDD
0V
Vin rising time
3.3v
0.5 ms
0.9VDD
Page No. 14/26
VDD
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed,
distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
Document Title
Document No. Revision 1.0
HSD101PFW1 Specification
Page No. 15/26
6.2 Switching Characteristics for LVDS Receiver
Item Symbol Min. Typ. Max. Unit Conditions
Differential Input High Threshold Vth
Differential Input Low Threshold Vtl -100
Input Current
Differential input Voltage
Common Mode Voltage Offset VCM (|VID|/2)
6.3 Bit Mapping & Interface Definition
7T
6.5/7T
5.5/7T
4.5/7T
3.5/7T
2.5/7T
1.5/7T
0.5/7T
RCLK
www.jxlcd.com
www.jxlcd.com
Rin0
R[2]
－
－
－
I
IN
|VID|
-10
0.1
－
－
1.25
R[1] R[0] G[0] R[5] R[4] R[3]
100 mV
VCM=1.2V
－
mV
+10 uA
0.6 V
2.4-(|VID|/2) V
R[2]
R[1] R[0]
G[0]
Rin1
Rin2
B[4] B[3] B[2] DE
G[2] G[1] B[1] B[0] G[5]
Pervious cycle Current cycle Next cycle
LVDS Receiver Input Timing Definition
(VS)
(HS)
G[4] G[3] G[2]
B[5] B[4] B[3]
G[1] B[1] G[3]
B[2] DE
for 6bits LVDS input
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed,
distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
Document Title
Document No. Revision 1.0
6.4 Interface Timing (DE mode)
Frame Rate -- 55 60 65 Hz
Frame Period t1 612 625 681 line
Vertical Display Time t2 576 576 576 line
Vertical Blanking Time t3 36 49 105 line
1 Line Scanning Time t4 1160 1200 1252 clock
Horizontal Display Time t5 1024 1024 1024 clock
Horizontal Blanking Time t6 136 176 228 clock
Clock Rate t7 39 45 51.42 MHz
Timing Diagram of Interface Signal (DE mode)
www.jxlcd.com
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed,
distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
www.jxlcd.com
HSD101PFW1 Specification
Item Symbol
Min. Typ. Max. Unit
X574 X575 X576
Page No. 16/26
HannStar Display Corp.
Document Title
Document No. Revision 1.0
6.5 Power On / Off Sequence
Power Supply
0.1V
0V
Signal
0V
HSD101PFW1 Specification
Power On
0.9VDD
DD
TP1
TP2
0.6V 0.6V
Power
TP3
Off
0.9VDD
0.1V
Page No. 17/26
DD
TP4
0.1V
DD
Note
Backlight
(Recommended
Item Min. Typ. Max. Unit Remark
www.jxlcd.com
www.jxlcd.com
：
(1) The supply voltage of the external system for the module input should be the same
：
：：
(2) Apply the lamp volatge within the LCD operation range. When the back-light turns
(3) In case of VDD = off level, please keep the level of input signal on the low or
TP1 0.5 -- 10 msec
TP2 0 -- 50 msec
TP3 0 -- 50 msec
TP4 500 -- -- msec
TP5 200 -- -- msec
TP6 200 -- -- msec
as the definition of VDD.
on before the LCD operation or the LCD truns off before the back-light turns off, the
display may momentarily become white.
TP5
50%
)
TP6
50%
keep a high impedance.
(4) TP4 should be measured after the module has been fully discharged between
power off and on period.
(5) Interface signal shall not be kept at high impedance when the power is on.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed,
distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
Document Title
Document No. Revision 1.0
6.6 Backlight Unit
Parameter Symbol Min Typ Max Units Condition
HSD101PFW1 Specification
Page No. 18/26
LED Current IF -- 20 20.6 mA
LED Voltage VF 3.0 3.2 3.4 Volt
P
LED Power
consumption
LED Life-Time N/A 10,000 -- -- Hour
Note (1): Calculator value for reference P=IF x VF x N (LED Qty’)
Note (2): The LED lifetime defines as the estimated time to 50% degradation of final
luminous.
6.7 LED Driver
6.7.1 Absolute Maximum Ratings
Item Symbol Min. Max. Unit Note
LED Power Supply voltage
LED_EN, PWM pin Voltage
www.jxlcd.com
www.jxlcd.com
6.7.2 DC Electrical Characteristics
--
LED
V
LED
VEN, V
-0.3 24 Volt
PWM
1.75 1.89
-- 5.5 Volt
Watt
Ta=25
Ta=25
Ta=25
Ta=25
IF=20mA
℃
℃
℃
Note (1)
℃
Note (2)
Parameter Symbol Min Typ Max Units
LED Power
Supply Voltage
LED_EN High
Threshold
LED_EN Low
Threshold
PWM High
Threshold
PWM Low
Threshold
PWM Frequency
PWM Duty Cycle
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed,
distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
V
V
V
V
PWMH
V
PWML
F
LED
ENH
ENL
PWM
T
D
5.0 -- 21.0 Volt
2.0 -- -- Volt
-- -- 0.3 Volt
3.0 -- -- Volt
-- -- 0.2 Volt
--
200
10 -- -- %
300
Hz
HannStar Display Corp.
Dimming
Signal
, LED_EN
Document Title
Document No. Revision 1.0
Note: PWM Duty Cycle. Pulse duty the bigger the brighter.
Duty Cycle TD= (t / T) x 100%
6.7.3 LED Power on/off sequence
LED Power Supply, V
HSD101PFW1 Specification
T1 T2 T4 T5
LED
0.9V
LED
T
t
T3
Page No. 19/26
0.9V
0.1V
0V
LED
0.1V
LED
www.jxlcd.com
www.jxlcd.com
LED Enable
Note (1): The duty of LED dimming signal should be more than 20% in T2 and T3
0V
0V
, PWM
Symbol
T1
T2
T3
T4
T5
Value
Min Typ Max
10 -- -10 -- -50 -- --
0 -- --
10 -- --
Unit
ms
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed,
distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
100 cycles
20
40
Document Title
Document No. Revision 1.0
HSD101PFW1 Specification
Page No. 20/26
7.0 Reliability test items
No.
1 High Temperature Storage Ta=+60oC, 240hrs
2 Low Temperature Storage Ta=-20oC, 240hrs
High Temperature Operation Ta=+50
3
Low Temperature Operation Ta=0
4
5 Thermal Cycling Test (non operation) -20oC(30min)→+60oC(30min),
Vibration
6
7 Shock
Storage / Operating temperature
www.jxlcd.com
www.jxlcd.com
Note .Max wet bulb temp.=39oC
Item Conditions Remark
o
C, 500hrs
o
C, 500hrs
Sine Wave
1.5G, 5~500Hz, XYZ
30min/each direction
Half-Sine, 200G, 2ms, ±XYZ, 1time
Humidity (%)
-20 -40
100
90
80
60
40
Storage Range
10
0
0
Temperature (oC)
Operating Range
20
50
60
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed,
distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
Document Title
Document No. Revision 1.0
HSD101PFW1 Specification
Page No. 21/26
8.0 OUTLINE DIMENSION
8.1 Front View Outline Dimension
nit : mm
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed,
distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
www.jxlcd.com
www.jxlcd.com
Note:
1. Model: HSD101PFW1-B00
2. Outline: 235*143*5.2(max)
3. Customer nut:4-M2(nut depth
4. General tolerance:+/-0.5mm
5. I/F connector
6.
7. Unit: mm
Cutaway view A-A[2]
18mm-max)
Part 20455-040E-12 or equivalent
User mounting torque spec:
2kgf-cm
0
HannStar Display Corp.
Document Title
Document No. Revision 1.0
8.2 Back View Outline Dimension
www.jxlcd.com
www.jxlcd.com
HSD101PFW1 Specification
Page No. 22/26
BM Assembly Tolerance
| A-A’ | ≤ 1 (mm)
| B-B’ | ≤ 1 (mm)
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed,
distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
11
Rev
Document Title
Document No. Revision 1.0
9.0 LOT MARK
9.1 Lot Mark
HSD101PFW1 Specification
Page No. 23/26
1 2 3 4 5 6 7 8 9 10
Code 1,2,3,4,5,6: HannStar internal flow control code.
Code 7: production location.
Code 8: production year.
Code 9: production month.
Code 10,11,12,13,14,15: serial number.
Note (1) Production Year
Year 2006
Mark 6 7 8 9 0 1 2 3 4 5
Note (2) Production Month
Month Jan. Feb. Mar. Apr. May. Jun. Jul. Aug. Sep. Oct Nov. Dec.
Mark 1 2 3 4 5 6 7 8 9 A B C
www.jxlcd.com
9.2 Location of Lot Mark
www.jxlcd.com
(1) Location : The label is attached to the backside of the LCD module. See Product back
view. ( Section 8.0 :
(2) Detail of the Mark : As attached below
(3) This is subject to change without prior notice.
2007
2008 2009 2010 2011 2012 2013 2014 2015
OUTLINE DIMENSION )
12 13
14 15
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed,
distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HSD101PFW1
: * -B
EDX.X 6 A0
HannStar Display Corp.
Document Title
Document No. Revision 1.0
HSD101PFW1 Specification
Page No. 24/26
10.0 PACKAGE SPECIFICATION
10.1 Packing form
LCM Model LCM Qty. in the box
HSD101PFW-B
10.2 Packing assembly drawings
Inner Box Size
50 pcs/box
www.jxlcd.com
www.jxlcd.com
Ref.460 x 316 x 321
(mm)
H
Notice
HSD101PFW1-B Material Notice
Box Corrugated Paper Board
Partition/Pad Corrugated Paper Board
Corner Pad Corrugated Paper Board
ESD bag PE --
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed,
distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
(AB Flute)
(B Flute)
(AB Flute)
HannStar Display Corp.
Document Title
Document No. Revision 1.0
11.0 GENERAL PRECAUTION
11.1 Use Restriction
This product is not authorized for use in life supporting systems, aircraft navigation control
systems, military systems and any other application where performance failure could be
life-threatening or otherwise catastrophic.
11.2 Disassembling or Modification
Do not disassemble or modify the module. It may damage sensitive parts inside LCD
module, and may cause scratches or dust on the display. HannStar does not warrant the
module, if customers disassemble or modify the module.
11.3 Breakage of LCD Panel
11.3.1.If LCD panel is broken and liquid crystal spills out, do not ingest or inhale liquid
crystal, and do not contact liquid crystal with skin.
11.3.2. If liquid crystal contacts mouth or eyes, rinse out with water immediately.
11.3.3. If liquid crystal contacts skin or cloths, wash it off immediately with alcohol and
11.3.4. Handle carefully with chips of glass that may cause injury, when the glass is
11.4 Electric Shock
www.jxlcd.com
www.jxlcd.com
11.4.1. Disconnect power supply before handling LCD module.
11.4.2. Do not pull or fold the LED cable.
11.4.3. Do not touch the parts inside LCD modules and the fluorescent LED’s connector
or cables in order to prevent electric shock.
11.5 Absolute Maximum Ratings and Power Protection Circuit
11.5.1. Do not exceed the absolute maximum rating values, such as the supply voltage
11.5.2. Please do not leave LCD module in the environment of high humidity and high
11.5.3. It’s recommended to employ protection circuit for power supply.
11.6 Operation
11.6.1 Do not touch, push or rub the polarizer with anything harder than HB pencil lead.
11.6.2 Use fingerstalls of soft gloves in order to keep clean display quality, when persons
11.6.3 When the surface is dusty, please wipe gently with absorbent cotton or other soft
HSD101PFW1 Specification
rinse thoroughly with water.
broken.
variation, input voltage variation, variation in parts’ parameters, environmental
temperature, etc., otherwise LCD module may be damaged.
temperature for a long time.
handle the LCD module for incoming inspection or assembly.
material.
Page No. 25/26
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed,
distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
Document Title
Document No. Revision 1.0
11.6.4 Wipe off saliva or water drops as soon as possible. If saliva or water drops
11.6.5 When cleaning the adhesives, please use absorbent cotton wetted with a little
11.7 Mechanism
Please mount LCD module by using mounting holes arranged in four corners tightly.
11.8 Static Electricity
11.8.1 Protection film must remove very slowly from the surface of LCD module to
prevent from electrostatic occurrence.
11.8.2 Because LCD module use CMOS-IC on circuit board and TFT-LCD panel, it is
11.9 Strong Light Exposure
The module shall not be exposed under strong light such as direct sunlight. Otherwise,
display characteristics may be changed.
www.jxlcd.com
11.10 Disposal
When disposing LCD module, obey the local environmental regulations.
www.jxlcd.com
HSD101PFW1 Specification
contact with polarizer for a long time, they may causes deformation or color
fading.
petroleum benzine or other adequate solvent.
very weak to electrostatic discharge. Please be careful with electrostatic
discharge. Persons who handle the module should be grounded through
adequate methods.
Page No. 26/26
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not be disclosed,
distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Loading...