HannStar Display Corp.
is document is the exclusive property of HannStar Display Corporation. It shall not be
Document Title HSD100IFW1-C Formal Specification Page No. 1/26
Document No. Revision 1.0
HannStar Product Specification
(Formal)
10” Color TFT-LCD Module
www.jxlcd.com
www.jxlcd.com
Note: 1.Please contact HannStar Display Corp. before designing your product based on this
module specification.
2.The information contained herein is presented merely to indicate the characteristics and
performance of our products. No responsibility is assumed by HannStar for any intellectual
property claims or other problems that may result from application based on the module
described herein.
Model: HSD100IFW1
-C
The information contained in th
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
is document is the exclusive property of HannStar Display Corporation. It shall not be
Document Title HSD100IFW1-C Formal Specification Page No. 2/26
Document No. Revision 1.0
Record of Revisions
Rev.
1.0
Date Sub-Model
-
www.jxlcd.com
www.jxlcd.com
Formal Product Specification was first released
Description of change
The information contained in th
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
is document is the exclusive property of HannStar Display Corporation. It shall not be
Document Title HSD100IFW1-C Formal Specification Page No. 3/26
Document No. Revision 1.0
Contents
1.0 General description ………………………………… p.4
2.0 Absolute maximum ratings……………………………. p.5
3.0 Optical characteristics.………………………………. p.6
4.0 Block diagram ……………………………………… p.10
5.0 Interface pin connection …………………………… p.11
6.0 Electrical characteristics …………………………… p.13
7.0 Reliability test items ………………………………… p.21
8.0 Outline dimension …………………………………… p.22
9.0 Lot mark ……………………………………………... p.23
10.0 Package specification ……………………………… p.24
11.0 General precaution …………………………………… p.25
www.jxlcd.com
www.jxlcd.com
The information contained in th
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
is document is the exclusive property of HannStar Display Corporation. It shall not be
Document Title HSD100IFW1-C Formal Specification Page No. 4/26
Document No. Revision 1.0
1.0 GENERAL DESCRIPTION
1.1 Introduction
HannStar Display model HSD100IFW1-C is a color active matrix thin film transistor
(TFT) liquid crystal display (LCD) that uses amorphous silicon TFT as a switching
device. This model is composed of a TFT LCD panel, a driving circuit and a back
light system. This TFT LCD has a 10.1 (17:10) inch diagonally measured active
display area with WSVGA (1024 horizontal by 600 vertical pixel) resolution.
1.2 Features
■ 10.1 (17:10 diagonal) inch configuration
■ 6 bits driver with 1channel TTL interface
■ RoHS and Halogen-Free Compliance
1.3 Applications
Portable DVD
Digital Photo frame
Display terminal for AV application
1.4 General information
Item Specification Unit
Outline Dimension 235 x 145.8 x 5.5 (Typ.) mm
Display area 220.416(H) x 129.15(V) mm
www.jxlcd.com
www.jxlcd.com
Number of Pixel 1024 RGB (H) x 600(V) pixels
Pixel pitch 0.21525(H) x 0.21525(V) mm
Pixel arrangement RGB Vertical stripe
Display mode Normally white
Surface treatment Antiglare, Hard-Coating (3H) with EWV film
Weight 255 (Typ.) g
Back-light Single LED (Side-Light type)
Power
Consumption
1.5 Mechanical Information
Module
Size
Weight
Logic System 0.55 (Max.) W
B/L System 2.4 (Max.) W
Item Min. Typ. Max. Unit
Horizontal (H) 234.5 235 235.5 mm
Vertical (V) 145.3 145.8 146.3 mm
Depth (D)
－
－
5.5
255
5.8 mm
－
g
The information contained in th
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
is document is the exclusive property of HannStar Display Corporation. It shall not be
Document Title HSD100IFW1-C Formal Specification Page No. 5/26
Document No. Revision 1.0
2.0 ABSOLUTE MAXIMUM RATINGS
2.1 Electrical Absolute Rating
2.1.1 TFT LCD Module
Item Symbol Min. Max. Unit Note
Digital Supply voltage
Analog Supply voltage
VCC -0.5 5 V
AVDD -0.5 13.5 V
Supply voltage
Digital input voltage
2.1.2 Back-Light Unit
Item Symbol Typ. Max. Unit Note
LED current IL 200
LED voltage VL 9.9 10.6 V (1) (2)(3)
Note (1) Permanent damage may occur to the LCD module if beyond this specification.
Functional operation should be restricted to the conditions described under
normal operating conditions.
(2) Ta =25±2℃
www.jxlcd.com
www.jxlcd.com
(3) Test Condition: LED current 200 mA. The LED lifetime could be decreased if
operating IL is larger than 200mA.
2.2 Environment Absolute Rating
Item Symbol Min. Max. Unit Note
Operating Temperature T
Storage Temperature T
V1~V7 0.4AVDD AVDD+0.3
V8~V14 -0.3 0.6AVDD
- -0.5 VCC+0.5
－
mA (1) (2)(3)
0 50
opa
-20 60
stg
V
V
V
℃
℃
The information contained in th
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
is document is the exclusive property of HannStar Display Corporation. It shall not be
Document Title HSD100IFW1-C Formal Specification Page No. 6/26
Document No. Revision 1.0
3.0 OPTICAL CHARACTERISTICS
3.1 Optical specification
Item Symbol Condition Min. Typ. Max. Unit Note
Contrast CR
Response
time
White luminance
(Center)
Color
chromaticity
(CIE1931)
Viewing
angle
Brightness uniformity B
Optima View Direction
3.2 Measuring Condition
www.jxlcd.com
www.jxlcd.com
■ Measuring surrounding：dark room
■ LED current I
■ Ambient temperature：25±2oC
■ 15min. warm-up time.
Rising TR
Falling TF
White
Hor.
Ver.
400 500
－
Θ=0
Normal
YL 200 250
Wx
Wy
Θ
Θ
Θ
Θ
UNI
：
200mA
L
L
R
U
D
viewing
angle
CR>10
Θ=0
－
0.260 0.310 0.360
0.280 0.330 0.380
60 70
60 70
40 50
50 60
70
6 O’clock
－
5 7
20 28
－
－
－
－
－
－ －
(1)(2)
msec
cd/m
% (5)
(1)(3)
(1)(4)
2
(IL=200mA)
(1)(4)
(6)
The information contained in th
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
is document is the exclusive property of HannStar Display Corporation. It shall not be
o
Document Title HSD100IFW1-C Formal Specification Page No. 7/26
Document No. Revision 1.0
3.3 Measuring Equipment
■ FPM520 of Westar Display technologies, INC., which utilized SR-3 for Chromaticity
and BM-5A for other optical characteristics.
■ Measuring spot size：20 ~ 21 mm
Note (1) Definition of Viewing Angle:
Note (2) Definition of Contrast Ratio (CR) :
measured at the center point of panel
Luminance with all pixels white
CR =
Luminance with all pixels black
www.jxlcd.com
www.jxlcd.com
Φ=180
Θ
L
6’ o’clock
Φ=270
Θ
D
Θ
U
12’ o’clock
Φ=90
Θ
o
o
R
Φ=0o
The information contained in th
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
is document is the exclusive property of HannStar Display Corporation. It shall not be
Document Title HSD100IFW1-C Formal Specification Page No. 8/26
Document No. Revision 1.0
Note (3) Definition of Response Time : Sum of TR and TF
white(TFT OFF) black (TFT ON) white(TFT OFF)
T
R
100%
90%
Optical
response
Note (4) Definition of optical measurement setup
www.jxlcd.com
www.jxlcd.com
10%
0%
T
F
time
The information contained in th
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
is document is the exclusive property of HannStar Display Corporation. It shall not be
Document Title HSD100IFW1-C Formal Specification Page No. 9/26
Document No. Revision 1.0
Note (5) Definition of brightness uniformity
16.67% 50.00% 83.33%
Y2 Y3 Y4
Y9 Y1 Y5
Y8 Y7 Y6
16.67%
50.00%
83.33%
www.jxlcd.com
www.jxlcd.com
Luminance uniformity = ×100%
Note (6)：Rubbing Direction (The different Rubbing Direction will cause the different
optima view direction.
The information contained in th
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
(Min Luminance of 9 points)
(Max Luminance of 9 points)
HannStar Display Corp.
is document is the exclusive property of HannStar Display Corporation. It shall not be
1024 pixel (3072 Dots)
B G
Document Title HSD100IFW1-C Formal Specification Page No. 10/26
Document No. Revision 1.0
4.0 BLOCK DIAGRAM
4.1 TFT LCD Module:
1024(RGB)x600
G/D
CN3
www.jxlcd.com
www.jxlcd.com
4.2 Pixel Format
1,1
2,1
600,1
1,2 1,3 1,4
X-PCB
S/D S/D
LED
CN2
S/D
CN1
1,1024
LCD Display Area
1 Pixel
R
R
R
600,
1024
600 Lines
The information contained in th
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
is document is the exclusive property of HannStar Display Corporation. It shall not be
Vertical Line start pulse I/O signal
Vertical Line output Enable signal
Vertical Line Clock
Vertical Line st
Document Title HSD100IFW1-C Formal Specification Page No. 11/26
Document No. Revision 1.0
5.0 INTERFACE PIN CONNECTION
5.1 TFT LCD Module
CN1 (Input signal): 30pin, 0.5mm pitch, AF7301-N2G11A (P-TWO or equivalent)
Pin No. Signal Description
1 POL Polarity Setting
2 STVD
3 OE123R
4 G-CLKR
5 STVU
6 GND Digital Power Ground
7 EDGSEL
8 VCC Digital Voltage Input
9 V9 Gamma Voltage Input
10 VGL Gate OFF Voltage
11 V2 Gamma Voltage Input
12 VGH Gate ON Voltage
13 V6 Gamma Voltage Input
14 UDC
www.jxlcd.com
www.jxlcd.com
15 VCOM Common Voltage
16 AGND Analog Power Ground
17 AVDD Analog Voltage Input
18 V14 Gamma Voltage Input
19 V11 Gamma Voltage Input
20 V8 Gamma Voltage Input
21 V5 Gamma Voltage Input
22 V3 Gamma Voltage Input
23 GND Digital Power Ground
24 R5 Red Data Bus Input (MSB)
25 R4 Red Data Bus Input
26 R3 Red Data Bus Input
27 R2 Red Data Bus Input
28 R1 Red Data Bus Input
29 R0 Red Data Bus Input (LSB)
30 GND Digital Power Ground
：
：
：：
art pulse I/O signal
Define clock edge select input, default EDGSEL=L.
EDGSEL=L Latch data by rising edge of clock
EDGSEL=H Latch data by rising and falling edges of clock
Shift up/down control signal
UDC = "H", up shift:
STVD (Input) G1 ~ G600STVU (Output)
UDC= "L", down shift:
STVU (Input) G600~G1STVD (Output)
The information contained in th
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
is document is the exclusive property of HannStar Display Corporation. It shall not be
Document Title HSD100IFW1-C Formal Specification Page No. 12/26
Document No. Revision 1.0
CN2 (Input signal): 30pin, 0.5mm pitch,AF7301-N2G11A (P-TWO or equivalent)
Pin No. Signal Description
1 GND Digital Power Ground
2 G5 Green Data Bus Input (MSB)
3 G4 Green Data Bus Input
4 G3 Green Data Bus Input
5 G2 Green Data Bus Input
6 G1 Green Data Bus Input
7 G0 Green Data Bus Input (LSB)
8 DIO2_COF3 Horizontal Line start pulse I/O signal (STHR)
9 REV Data Invert signal
10 GND Digital Power Ground
11 CLK Pixel clock
12 VCC Digital Voltage Input
13 DIO1_COF1 Horizontal Line start pulse I/O signal (STHL)
14 LD Polarity latch and re-flash new data to output
15 B5 Blue Data Bus Input (MSB)
16 B4 Blue Data Bus Input
17 B3 Blue Data Bus Input
18 B2 Blue Data Bus Input
19 B1 Blue Data Bus Input
20 B0 Blue Data Bus Input (LSB)
Select left or right shift, normally pulled high.
www.jxlcd.com
21 LRC
www.jxlcd.com
22 V1 Gamma Voltage Input
23 V4 Gamma Voltage Input
24 V7 Gamma Voltage Input
25 V10 Gamma Voltage Input
26 V12 Gamma Voltage Input
27 V13 Gamma Voltage Input
28 AVDD Analog Voltage Input
29 AGND Analog Power Ground
30 VCOM Common Voltage
5.2 Back-Light Unit
CN3 LED Power Source (BHSR-02VS-1) or equivalent
Mating Connector: (SBHT-002T-P0.5) or equivalent
Terminal no. Symbol Function
1 VL LED power supply (high voltage)
2 GL LED power supply (low voltage)
SHL=“1”: DIO1 OUT1,2,3OUT4,5,6
OUT1198,1199,1200 = DIO2
SHL=“0”: DIO1= OUT1,2,3 OUT4,5,6
OUT1198,1199,1200DIO2
The information contained in th
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
is document is the exclusive property of HannStar Display Corporation. It shall not be
Current of power
Document Title HSD100IFW1-C Formal Specification Page No. 13/26
Document No. Revision 1.0
6.0 ELECTRICAL CHARACTERISTICS
6.1 TFT LCD Module
Item Symbol Min. Typ. Max. Unit
Vcc 3.0 3.3 3.6 V Note (2), Note (3)
Supply Voltage
VGH 14.55 15 15.45 V Note (2), Note (3)
VGL -7.35 -7 -6.65 V Note (2), Note (3)
AVDD 9.22 9.48 9.75 V Note (2), Note (3)
Note
VCOM V
Input signal
voltage
supply
Input level of
V1~V5
Input level of
V6~V10
www.jxlcd.com
Note (1): HSYNC, VSYNC, DE, Digital Data
Note (2): Be sure to apply the power voltage as the power sequence spec.
Note (3): DGND=AGND=0V
www.jxlcd.com
COMin
3.21 3.41 3.61 V
ViH 0.7 Vcc
ViL 0 - 0.3 Vcc
ICC - 6.4 - mA Vcc = 3.3V (Black)
I
ADD
- 54 - mA AVDD= 9.5 V (Black)
IGH - 0.2 - mA VGH= 15 V
IGL - 0.5 - mA VGL= -7 V
Vx AVDD/2
Vx 0.1 - AVDD/2
- Vcc V Note (1)
V
- AVDD-0.1
V
V
The information contained in th
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
is document is the exclusive property of HannStar Display Corporation. It shall not be
White (
Ground)
Black
2
Document Title HSD100IFW1-C Formal Specification Page No. 14/26
Document No. Revision 1.0
6.2 Back-Light Unit
The back-light system is an edge-lighting type with 30 LED.
The characteristics of the LED are shown in the following tables.
Item Symbol Min. Typ. Max.
LED current IL
LED voltage VL
Operating LED life time
Hr 20000
－
200
－
9.9 10.6
－
－
－
mA (2)
Hour (1)(2)
Unit Note
V
LCD MODULE
1
Power Supply
A
Note (1) LED life time (Hr) can be defined as the time in which it continues to
www.jxlcd.com
www.jxlcd.com
Note (2) The “LED life time” is defined as the module brightness decrease to
operate under the condition: Ta=25±3 oC, typical IL value indicated in
the above table until the brightness becomes less than 50%.
50% original brightness at Ta=25℃ and IL=200mA. The LED lifetime
could be decreased if operating IL is larger than 200mA. The
constant current driving method is suggested.
LED Light Bar Circuit
The information contained in th
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
is document is the exclusive property of HannStar Display Corporation. It shall not be
Document Title HSD100IFW1-C Formal Specification Page No. 15/26
Document No. Revision 1.0
Note (3) Suggested Schematic of LED Back-Light Driver
www.jxlcd.com
www.jxlcd.com
Suggested Schematic of LED Back-Light Driver
The information contained in th
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
is document is the exclusive property of HannStar Display Corporation. It shall not be
Document Title HSD100IFW1-C Formal Specification Page No. 16/26
Document No. Revision 1.0
6.3 AC Characteristics
Source Driver Timing
Item Symbol Min. Typ. Max.
CLK frequency Fclk - 55 70 MHz CLK pulse width Tcw
Data set-up time Tsu
Data hold time Thd
Propagation delay of DIO2/1 Tphl
Time that the last data to LD Tld
Pulse width of LD Twld
Time that LD to DIO1/2 Tlds
POL set-up time Tpsu
POL hold time
Tphd
6 4 2 -
6 10 15
1 -
2 - 5 - 6 - 6
- ns -
- ns -
- ns -
- Tcph -
ns
Unit Note
ns
Tcph Tcph -
ns
CL=25pF
( Output )
POL to LD
POL to LD
Gate Driver Timing
Item Symbol Min. Typ. Max.
CPV period Tcpv
www.jxlcd.com
www.jxlcd.com
CPV pulse width
OE pulse width Twoe
Data setup time Tsu
Data hold time Thd
Tcpvh,
Tcpvl
5
2.5 - 1 - -
0.7 - -
0.7 - -
- - us -
Unit Note
us 50% duty cycle
us -
us us -
The information contained in th
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
is document is the exclusive property of HannStar Display Corporation. It shall not be
Document Title HSD100IFW1-C Formal Specification Page No. 17/26
Document No. Revision 1.0
6.4 Timing Diagram of Interface Signal
Source Driver Timing
Tcph
70% 70%
30%
Tcw
CLK
DIO1/2
70%
70%
Tsu
Thd
70%
70%
30%
Tcw
70%
(input)
Tsu
Thd
Data,REV
70%
First data Second data Last data
Tphl
DIO1/2
(output)
www.jxlcd.com
www.jxlcd.com
CLK
70%
70%
Tld
70% 70%
LD
Twld
Tlds
DIO1/2
(input)
70%
70%
Tphl
30%
70%
LD
Tpsu Tphd
POL
70%
70%
The information contained in th
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
is document is the exclusive property of HannStar Display Corporation. It shall not be
Document Title HSD100IFW1-C Formal Specification Page No. 18/26
Document No. Revision 1.0
Gate Driver Timing
Tcph Tcpl
Tcpv
50%
CPV
Tsu
STVU
Twoe
50%
OE
www.jxlcd.com
www.jxlcd.com
Thd
50%
The information contained in th
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
is document is the exclusive property of HannStar Display Corporation. It shall not be
0.9VDD
0.9VDD
Document Title HSD100IFW1-C Formal Specification Page No. 19/26
Document No. Revision 1.0
6.5 Power On / Off Sequence
Power On
Power Off
Power Supply
0V
0V
0.1V
Signal
DD
TP1
TP2
0.6V
TP5
TP3
0.6V
TP6
0.1V
DD
TP4
0.1V
DD
Backlight
(Recommended)
www.jxlcd.com
www.jxlcd.com
Item Min. Typ. Max. Unit Remark
TP1 0.5 -- 10 msec
TP2 0 -- 50 msec
TP3 0 -- 50 msec
TP4 500 -- -- msec
TP5 200 -- -- msec
TP6 200 -- -- msec
50%
50%
Level define
90%
10%
T
Power On Sequence: VCC-> AVDD -> VGL -> VGH -> Data -> B/L
Power Off Sequence: B/L-> Data -> VGH -> VGL -> AVDD -> VCC
Notes: Data include R0~R7, G0~G7, B0~B7, HSD, VSD, DCLK, SHLR, UPDN, DE
MODE, RSTB, STBYB, SHLR, UPDN, DITH
The information contained in th
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
is document is the exclusive property of HannStar Display Corporation. It shall not be
R2 R3 R4
R6 R7
Document Title HSD100IFW1-C Formal Specification Page No. 20/26
Document No. Revision 1.0
6.6 Gamma circuit
www.jxlcd.com
R1
R8
www.jxlcd.com
R5
R9
R10
R11
R12
*Suggested Gamma Circuit. (AVDD=9.5V).
R13
R14
R15
The information contained in th
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
is document is the exclusive property of HannStar Display Corporation. It shall not be
C(30min), 100 cycles
Document Title HSD100IFW1-C Formal Specification Page No. 21/26
Document No. Revision 1.0
7.0 Reliability test items
No. Item Conditions Remark
1 High Temperature Storage Ta=+60oC, 240hrs
2 Low Temperature Storage Ta=-20oC, 240hrs
High Temperature Operation Ta=+50oC, 500hrs
3
Low Temperature Operation Ta=0oC, 500hrs
4
5 High Temperature and High Humidity
(operation)
6 Thermal Cycling Test (non operation) -20oC(30min) → +60
7 Electrostatic Discharge
8 Vibration
9 Shock
10 Vibration (with carton)
www.jxlcd.com
www.jxlcd.com
11 Drop (with carton)
Note: There is no display function NG issue occurred, all the cosmetic specification is judged
before the reliability stress.
1.Random:
2.Sine:
Half-Sine, 220G, 2ms, ±XYZ, 1time
Random:
Height：60 cm
1 corner, 3 edges, 6 surfaces
Ta=+50oC, 80%RH, 500hrs
o
±
200V,200pF(0Ω) 1 time/connector
1.04G, 10~500Hz, XYZ,
30min/each direction
1.5G, 5~500Hz, XYZ
30min/each direction
1.04G, 10~500Hz, XYZ,
45min/each direction
JIS Z0202
The information contained in th
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
is document is the exclusive property of HannStar Display Corporation. It shall not be
Document Title HSD100IFW1-C Formal Specification Page No. 22/26
Document No. Revision 1.0
8.0 OUTLINE DIMENSION
8.1 Outline Dimension
nit : mm
www.jxlcd.com
www.jxlcd.com
The information contained in th
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
is document is the exclusive property of HannStar Display Corporation. It shall not be
２
３
４
５
６
７
８
９
10
11
12
13
14
15
Document Title HSD100IFW1-C Formal Specification Page No. 23/26
Document No. Revision 1.0
9.0 LOT MARK
9.1 Lot Mark
１
Code 1,2,3,4,5,6: HannStar internal flow control code.
Code 7: production location.
Code 8: production year.
Code 9: production month.
Code 10,11,12,13,14,15: serial number.
Note (1) Production Year: Code 8 is defined by the last number of the year, for example
Year 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010
Mark 1 2 3 4 5 6 7 8 9 0
Note (2) Production Month
Month Jan. Feb. Mar. Apr. May. Jun. Jul. Aug. Sep. Oct Nov. Dec.
www.jxlcd.com
Mark 1 2 3 4 5 6 7 8 9 A B C
www.jxlcd.com
9.2
Detail of Lot Mark
(1) Below label is attached on the backside of the LCD module. See Section 8.0:
Dimension.
(2) The detail of Lot Mark is attached as below.
(3) This is subject to change without prior notice.
HSD100IFW1
Rev: * -C
6 A0
Outline
The information contained in th
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
is document is the exclusive property of HannStar Display Corporation. It shall not be
Document Title HSD100IFW1-C Formal Specification Page No. 24/26
Document No. Revision 1.0
10.0 PACKAGE SPECIFICATION
10.1 Packing form
(1) Package quantity in one carton: 50 pieces.
(2) Carton size: 460 mm×361 mm×321 mm.
10.2 Packing assembly drawings
www.jxlcd.com
www.jxlcd.com
Material Notice
Box Corrugated Paper Board
Partition/Pad Corrugated Paper Board
Corner Pad Corrugated Paper Board
ESD bag PE
(AB Flute)
(B Flute)
(AB Flute)
The information contained in th
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
is document is the exclusive property of HannStar Display Corporation. It shall not be
Document Title HSD100IFW1-C Formal Specification Page No. 25/26
Document No. Revision 1.0
11.0 GENERAL PRECAUTION
11.1 Use Restriction
This product is not authorized for use in life supporting systems, aircraft navigation control
systems, military systems and any other application where performance failure could be
life-threatening or otherwise catastrophic.
11.2 Disassembling or Modification
Do not disassemble or modify the module. It may damage sensitive parts inside LCD
module, and may cause scratches or dust on the display. HannStar does not warrant the
module, if customers disassemble or modify the module.
11.3 Breakage of LCD Panel
11.3.1.If LCD panel is broken and liquid crystal spills out, do not ingest or inhale liquid
crystal, and do not contact liquid crystal with skin.
11.3.2. If liquid crystal contacts mouth or eyes, rinse out with water immediately.
11.3.3. If liquid crystal contacts skin or cloths, wash it off immediately with alcohol and
rinse thoroughly with water.
11.3.4. Handle carefully with chips of glass that may cause injury, when the glass is
broken.
11.4 Electric Shock
www.jxlcd.com
www.jxlcd.com
11.4.1. Disconnect power supply before handling LCD module.
11.4.2. Do not pull or fold the LED cable.
11.4.3. Do not touch the parts inside LCD modules and the fluorescent LED’s connector
or cables in order to prevent electric shock.
11.5 Absolute Maximum Ratings and Power Protection Circuit
11.5.1. Do not exceed the absolute maximum rating values, such as the supply voltage
variation, input voltage variation, variation in parts’ parameters, environmental
temperature, etc., otherwise LCD module may be damaged.
11.5.2. Please do not leave LCD module in the environment of high humidity and high
temperature for a long time.
11.5.3. It’s recommended to employ protection circuit for power supply.
11.6 Operation
11.6.1 Do not touch, push or rub the polarizer with anything harder than HB pencil lead.
11.6.2 Use fingerstalls of soft gloves in order to keep clean display quality, when persons
handle the LCD module for incoming inspection or assembly.
11.6.3 When the surface is dusty, please wipe gently with absorbent cotton or other soft
material.
The information contained in th
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
HannStar Display Corp.
is document is the exclusive property of HannStar Display Corporation. It shall not be
Document Title HSD100IFW1-C Formal Specification Page No. 26/26
Document No. Revision 1.0
11.6.4 Wipe off saliva or water drops as soon as possible. If saliva or water drops
contact with polarizer for a long time, they may causes deformation or color
fading.
11.6.5 When cleaning the adhesives, please use absorbent cotton wetted with a little
petroleum benzine or other adequate solvent.
11.7 Mechanism
Please mount LCD module by using mounting holes arranged in four corners tightly.
11.8 Static Electricity
11.8.1 Protection film must remove very slowly from the surface of LCD module to
prevent from electrostatic occurrence.
11.8.2 Because LCD module use CMOS-IC on circuit board and TFT-LCD panel, it is
very weak to electrostatic discharge. Please be careful with electrostatic
discharge. Persons who handle the module should be grounded through
adequate methods.
11.9 Strong Light Exposure
The module shall not be exposed under strong light such as direct sunlight. Otherwise,
display characteristics may be changed.
www.jxlcd.com
11.10 Disposal
When disposing LCD module, obey the local environmental regulations.
www.jxlcd.com
The information contained in th
disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display Corporation.
Loading...