This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
1
Additional Information
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna
•Increase the separation between the equipment and receiver
•Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected
•Consult the dealer or an experienced radio/TV technician for help
Warning: You are cautioned that changes or modifications not
expressly approved by the party responsible for compliance could void
your authority to operate the equipment.
1. applies only to products purchased in the United States of America
3
DOC Compliance Notice
1
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the Radio Interference
Regulations of the Canadian Department of Communications.This
device complies with Canada ICES-003 Class B.
CE Conformity Statement
2
This device complies with the requirements set out in the Council
Directive on the approximation of the Laws of the Member States
relating to Electromagnetic Compatibility (89/336/EEC) and the
Amendment Directive (92/31/EEC), Low-Voltage Directive (73/23/EEC)
and the Amendment Directive (93/68/EEC).
1. applies only to products purchased in Canada
2. applies only to products purchased in the European Union
4
2
Description of Warning Symbols
Before You Proceed
1. Read all Safety Notices in Section 2 of this manual and
instructions in the User’s Manual carefully before either plugging
in or turning the TV on.
2. Keep this User’s Manual in a safe place for future reference.
Keep the box and packaging in case the TV needs to be shipped
in the future.
3. Follow the TV and warning label instructions.
4. Any uses, operations, changes, alterations or modifications of
the TV that do not follow the instructions in this manual will void
this TV’s warranty.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING
This symbol is used to alert
users to pay attention to
important descriptions
regarding usage, maintenance
(repair), and additional
important information related
to this TV.
CAUTION
This symbol is used to alert
users to the risk of electric
shocks due to dangerous and
uninsulated components.
5
3
Safety Notices
Electric Power Notice
Electric power may cause personal injury and mechanical damage if
misused. Although safety has been taken into consideration during the
design and production of this TV, electric shock or fire can result if the
TV is misused. To prevent potential danger, read and follow the
instructions and warnings contained in this manual when setting up,
operating or cleaning the TV. In addition, please read all “Safety
Notices” contained in this manual carefully before using the TV.
Power Supply Safety Notes
1. To avoid electric shocks, do not use an extended power cord or
an outlet that does not match this TV's plug or leaves the plug
exposed.
2. This TV has a 3-pin grounded plug. The third pin connects to
ground; do not remove it or alter it in anyway.
3. If the power cord or plug is damaged or worn, unplug it
immediately and contact an authorized service technician for
maintenance.
4. To avoid fire or electric shocks, do not overload electric power
outlets.
6
Installation Safety Notes
Antenna
We suggest that you use an outdoor antenna to get the best signal
possible unless you have cable TV or a centralized indoor antenna
system. You may, however, use an antenna indoors if it is placed in a
location free from interference.
Location
Avoid prolonged exposure to sunlight or other strong sources of heat.
Leave sufficient distance between the TV and the wall to provide
enough space for the emission of heat.
WARNING
To reduce the risk of fire or electric shock, do not expose this
apparatus to rain or moisture.
Apparatus shall not be exposed to dripping or splashing and no
objects filled with liquids, such as vases, shall be placed on the
apparatus.
Power
To avoid danger of fires or electric shock, only use those adapters
listed below, which are compatible with this TV.
• EDAC POWER ELECTRONICS CO., LTD.: EA1050A-120
• LI SHIN INTERNATIONAL ENTERPRISE CORP.: 0218B1260
7
IMPORTANT SAFETY INSTRUCTIONS
1 Read these instructions.
2Keep these instructions.
3Heed all warnings.
4Follow all instructions.
5Do not use this apparatus near water.
6Clean only with dry cloth.
7Do not block any ventilation openings. Install
in accordance with manufacturer’s
instructions.
8Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
8
9Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding-type plug has two blades
and a third grounding prong. The wide blade
or the third prong are provided for your
safety. If the provided plug does not fit into
your outlet, consult an electrician for
replacement of the obsolete outlet.
10 Protect the power cord from being walked on
or pinched, particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
11 Only use attachments/accessories specified
by the manufacturer.
12 Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or
sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13 Unplug this apparatus during lightning
storms or when unused for long periods of
time.
14 Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is
damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does
not operate normally, or has been dropped.
CAUTION
These servicing instructions are for use by
qualified service personnel only.To reduce
the risk of electric shock, do not perform any
servicing other than that contained in the
operating instructions unless you are
qualified to do so.
9
Personal Safety
To avoid overloading the power supply, never
plug too many electrical devices into an outlet,
power strip, or extension cable.
Dangerous high-voltage electric power
components are located inside the TV. To avoid
electric shock, do not disassemble the TV in any
way.
Do not place or drop metals, small objects, or
flammable materials into the vent of the TV.
If the TV is dropped, falls down, or is otherwise
damaged, unplug the power cord immediately
and contact an authorized service technician.
If any fluid is sprayed or dropped into the TV,
contact an authorized service technician.
10
The screen of the TV is made of glass. Avoid
hitting or scraping it. If the screen is broken, do
not touch the broken glass.
Do not allow children to use the TV unattended.
Installation
Do not place the TV in locations where there is
excessive steam or dust.
Avoid blocking the TV's vents, do not place the
TV on a bed, sofa, carpet, or in a sealed cabinet.
Install the outdoor antenna (not included) away
from power transmission lines to avoid possible
danger.
Unplug the power cord and antenna connector
when there is a storm or when the TV is not in
use for long periods to avoid electric shock from
lightning.
11
Operation
V
Maintenance
This TV is designed for home power sources as
labeled on the casing. Avoid using any other
power accessories to avoid electric shock or
other damage.
The plug can be inserted into an outlet in only
one direction as shown to the left. Do not alter
the plug. Contact an authorized service
technician if you cannot plug it in correctly.
If there is any problem that cannot be resolved
according to the instructions given in this
manual, contact an authorized service technician
immediately. Do not attempt any methods not
covered in this manual.
Do not attempt to repair the TV by yourself.
Contact an authorized service technician. Ask
the service technician to complete a safety
inspection before switching the power on after
completing any maintenance.
12
4
Preface
Thank you for purchasing a Hannspree Liquid Crystal Display Television
(LCD TV). Your new TV will allow you to enjoy superior audio and video
while enriching your lifestyle with advanced technology.
Please carefully read this manual in its entirety before setting up, using
or operating your TV. To ensure the safe and correct installation and
operations of the TV, it is important that the safety and operation
instructions in this manual are followed.
This instruction manual is designed to assist you in setting up and using
the TV. The information in this manual has been carefully checked for
accuracy; however, no guarantee is given to the correctness of the
contents. The information in this manual is subject to change without
notice.
To the extent allowed by applicable law, Hannspree California Inc.
(“Hannspree”) shall not be liable for direct, indirect, special, exemplary,
incidental or consequential damages arising from any defect or
omission in this manual, even if advised of the possibility of such
damages in advance.
All rights reserved. This manual is protected by copyright and
distributed under licenses restricting its use, copying and distribution.
No part of this manual may be reproduced in any form by any means
without the prior written authorization of Hannspree. The TV described
in this manual may include copyrighted software of Hannspree (or other
third parties). Hannspree (or other third parties) preserves the exclusive
rights for copyrighted software, such as the right to distribute or
reproduce the copyrighted software. Accordingly, and to the extent
allowed by applicable law, any copyrighted software contained in the
product described herein shall not be distributed, modified, reverse
engineered, or reproduced in any manner without the prior written
authorization of Hannspree (or of other third parties).
The Hannspree logos presented herein are trademarks of Hannspree.
All other product names, trademarks or logos mentioned herein are
used for identification purpose only, and may be the trademarks or
registered trademarks of their respective owners.
The purchase of the product described herein shall not be deemed to
grant, either directly or by implication, estoppel or otherwise, any
license under the copyrights, patents, patent applications or trademarks
of Hannspree, except for the normal, non-exclusive use that arises by
operation of law in the sale of a product.
14
5
Introducing the TV
Thank you for purchasing this LCD TV. Your TV is designed to be safe,
versatile, and easy to use. The unique design makes it a fun addition to any
room.
You can watch standard NTSC television channels and easily connect a
VCR, VCD, or DVD player to the standard Video and S-Video input ports
located at the rear of the unit.
Convenient control buttons located on the TV and a handy remote control let
you change channels, adjust the volume, and change display settings
through an easy-to-use on-screen display menu system. The TV speakers
provide full, rich stereo sound and a convenient audio output port lets you
connect to an external audio system or headphones.
On-screen display (OSD) menu system
Multi-channel Television Sounds (MTS) Stereo with SAP
Built-in stereo speakers
15
6
Checking Package Contents
Make sure the following components are included in the box. Please contact
Hannspree Customer Service immediately if anything is missing or
damaged.
TV
User’s manual
Quick start guide
Warranty and service manual
Power cord
Power adapter
4-IN-1 A/V cable
Remote control and battery/batteries
Mounting device
16
7
Getting Started
Control Panel
DescriptionIconFunction
Power
Turns the TV power on and off.
Press this button to eliminate sound.
Mute
MUTE
Press it again or press the
adjust
buttons directly to restore
volume
sound.
Selects the input source to be
Source
SOURCE
displayed (TV, AV
The source is displayed on the top
1, or AV2).
right corner of the screen.
Menu
Channel
select
MENU
the CH UP button
S)
(
the CH DOWN
button
(
T)
Turns the on-screen display (OSD)
menu on and off.
Channel up: Increases the channel
number.
Channel down: Decreases the
channel number.
These buttons are also used to
navigate the OSD menus.
Volum e up: Increases the volume.
Volume down: Decreases the
volume.
These buttons are also used to
navigate the OSD menus.
Volum e
adjust
the VOL UP button
(+)
the VOL DOWN
button
(–)
Power LEDGreen LED indicates power on.
Remote
Sensor
Receives signals from the remote
control.
17
Input and Output Jacks
DescriptionConnectorFunction
Use the AV1 input to connect an
external device, such as a VCR,
AV1 (S-VIDEO/
R/L/VIDEO)
AV2
ANT (Antenna
/cable TV in)
DC-IN
VCD, or DVD player.
Audio Input: AV connector audio
(white and red) cables.
Video Input: AV connector video
(yellow) cable or S-Video cable.
Use the included 4-IN-1 A/V
cable to connect external
devices, such as a VCR, VCD, or
DVD player.
Audio Input: AV connectors
audio (white and red) cables.
Video Input: AV connector video
(yellow) or S-Video cable.
Connects to an antenna or CATV
cable.
Connects to the power adapter.
LINE OUT
Headphone
jack
18
Connects to external amplified
speakers.
Connects to headphones.
()
Remote Control
T
DescriptionIconFunction
Menu button
Arrow buttons
Number buttons
Last button
CC button
Display button
MENU
S / T / W / X
123
456
789
0
LAS
CC
DISPLAY
Turns the on-screen display (OSD)
menu on and off.
Press S, T, W or X to scroll through
the on-screen display menus. You
can assign 4 favorite channels to the
arrow buttons.
See "Using the
Favorite Channel Feature" on page
31
Use to select a channel directly.
Press 0-9 to enter the channel
number (press 1 and 0 for channel
10).
Press this button to return to the last
channel selected.
Press this button to enable the
closed captions/subtitles (only
available in the United States of
America). This option may not be
available in your local area.
Press this button to show messages
on the screen, such as the channel
number, MTS mode and others.
Press the button again to close the
displayed message. This option may
not be available in your local area.
19
DescriptionIconFunction
(Multi-channel Television Sound)
The indicator on the top right corner
MTS button
MTS
of the screen is
program has MAIN/SAP/MONO
capabilities. Press it to enable the
bilingual function.
Press this button to eliminate sound.
Mute button
MUTE
Press it again or press the volume
adjust buttons to restore sound.
Press this button repeatedly to set
the length of time the TV remains
turned on (30, 60, 90, or 120
minutes).
Sleep button
SLEEP
A timer appears on the top right
corner of the screen to show the time
remaining.
Cancel the timer by pressing until the
displayed time disappears.
yellow when the
Power button
Volum e adjust
buttons
Channel select
buttons
Source button
20
-VOL VOL+
CH
CH
SOURCE
Turns the TV power on or off.
Volume up: Increases the volume.
Volume down: Decreases the
volume.
Channel up: Increases the channel
number.
Channel down: Decreases the
channel number.
Selects the input source to be
displayed (TV, AV1, AV2). The
source is displayed on the top right
corner of the screen.
Inserting the Remote Control Batteries
1
Open the battery compartment cover at the back of the remote control (A).
2 For AAA batteries: Insert the batteries paying attention to the
polarity markings inside the battery compartment (B).
For lithium batteries: Insert the battery/ batteries with the positive
side (+) facing up (B). Remember to slide the battery/ batteries
underneath the metal contacts. Press downward to set the
battery/batteries in place.
3 Replace the battery compartment cover (C)/(D).
A
B
C
AAA batteries
A
B
C
Lithium batteries 1
A
B
C
D
Lithium batteries 2
21
Loading...
+ 47 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.