HANK ELECTRONICS SO07W User Manual

Smart Plug

User Manual

HKWL-SO07W

HKWL-SO07WP

Ⅰ. PR ODUCT O VERVI EW

The Smart Plug is a wifi based switch which can be used to on/off
control the electrical appliances after paring to the wifi network. You
also monitor the on/off status of the appliances through your mobile
phone from anywhere as long as you have access to internet.

Ⅱ. PAC KAGE CON TENTS

Ÿ 1x Smart Plug
Ÿ 1x User Manual

Ⅲ.PRO DUCT FE ATURES

Ÿ Support WiFi connection
Ÿ Works with Amazon Alexa and Google Assistant
Ÿ Firmware OTA upgrade supported
Ÿ Easy installation, plug and play
Ÿ Timing task settings Supported
Ÿ Over current protection(Applicable only to SO07WP)

Ⅳ.PRO DUCT ST RUCTU RE

Led Indicator

Button

2 3 4

Ⅴ. PROD UCT OVE RVIEW

Power supply:

Power loss:

Nominal input voltage:

Rated current:

Storage temperature:

Operational temperature:

Wireless standard:

Radio frequency:

Encryption type:

Transmit power:

Sensitivity:

AC 90-135V,60Hz

≤1W

120V

15A max

-20-60℃

-10-40℃

IEEE802.11 b/g/n

2.4GHz—2.4835GHz

WEP/TKIP/AES,WPS

802.11b:18dBm±2dBm

802.11g:15dBm±2dBm

802.11n:15dBm±2dBm

802.11b:-91dBm@11Mbps 8%PER

802.11g:-75dBm@54Mbps 10%PER

802.11n:-72dBm@MCS7_HT20 10%PER

Ⅵ. POWE R INDIC ATOR

HKWL-SO07W HKWL-SO07WP

OFF: Purple red
ON: Blue

When the Power of the load changes from low to high, the color of
indicator will change in cycle as “blue, cyan, green, yellow, red,
purple…”. Total 6 grades, 300W each as difference. When the power
is over 1800W (6th grade). The indicator will blink in purple and shut
off the output in 10 seconds. (Applicable only to SO07WP)

OFF: Purple red
0~300W: Blue
300~600W: Cyan
600~900W: Green
900~1200W: Yellow
1200~1500W: Red
1500~1800W: Purple

Ⅶ. ADD &DELET E DEVIC ES

Scanning following two QR codes to download APP for Android and
IOS System

Android

IOS

1.Add Devices

• EZ mode
The moment the plug is powered, the LED Indicator will be flashing in
green. Chose EZ Mode to include the network in the APP. The app will
indicate the success when it's included successfully. The LED indicator
will be solid in blue.

5 6 7 8

• AP mode
The moment the plug is powered, the LED Indicator will be flashing in
green. Press and hold the button for 5 seconds and then release. The
LED indicator will blink slowly in yellow. Chose AP Mode to include
the network in the APP. The app will indicate the success when it's
included successfully. The LED indicator will be solid in blue.

2. Switching network inclusion modes

EZ mode (LED is flashing) is the default inclusion way. When the plug
is out of a network, switching the inclusion way from EZ mode and AP
mode can be done by pressing and hold the button for 5 seconds and
then release.

3. Removing from Wi-Fi network

Select the Smart Plug that you want to delete on the APP. Click the
icon at the upper right corner. Then click 'Delete' to remove the
device from the APP and network, the LED light will be flashing in
green.

NOTE:

After the smart plug is included to a network successfully.
You don't need to re-include it when it's powered again
after a power off. It will connect to the previous network
automatically. During this process, it's LED indicator will
blink slowly and later becomes solid.

Ⅷ. RES ET TO FACT ORY DEFA ULT

The way to reset the Smart Plug is press and hold the button for 5
seconds. The LED indicator will flash in green.

Notes

Ÿ The Smart Plug should be used in dry places (Using in bathrooms

etc. is not allowed.)

Ÿ Please use the Smart Plug in safe environment (Working power

higher than 1800W or current higher than 15A are not allowed)

Ⅸ. FCC NO TICE (F OR USA)

This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.

Note: The Grantee is not responsible for any changes or
modifications not expressly approved by the party
responsible for compliance. such modifications could void the
user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

Note: The device has been evaluated to meet general RF exposure

requirement. To maintain compliance with FCC's RF exposure guidelines, this
equipment should be installed and operated with a minimum distance of
20cm between the radiator and your body.