Hangzhou Tuya Information Technology TYZS5 User Manual
TYZS5 V1.0.0 Datasheet
1. Product Overview
The TYZS5 is a low-power embedded Zigbee module developed by Hangzhou Tuya
Information
integrated wireless RF processor chip and a small number of peripheral devices. It has a built-in
802.15.4 PHY/MAC Zigbee network protocol and a large number of library functions. The
TYZS5 embeds a low-power 32-bit ARM Cortex-M4 core, 512KByte Flash program memory,
64KB RAM data memory, and a wealth of peripheral resources.
Technology Co., Ltd. The module consists of a EFR32MG13P732HG highly
The TYZS5 is
one place. It enables users to build on the product and develop embedded Zigbee products that suit
their individual needs.
a FreeRTOS
platform that gathers all Zigbee MAC and TCP/IP libraries into
1.1 Features
A built-in low-power 32-bit
floating point unit that doubles as an application processor
Wide operating voltage: 1.8V-3.8V
Peripherals: 6×GPIOs, 1×UART (with flow control),
Zigbee operating characteristics：
Supports
Operating channels 11to 26@2.40
Built-in DC-DC circuit for maximum power efficiency
63uA/MHz operating power consumption; 1.4 uA sleep current
Active net pairing with terminal devices
Built-in PCB onboard antenna
Operating temperature: -40℃ to 85℃
Supports hardware encryption and supports AES 128/256
802.15.4 MAC/PHY
Cortex-M4 processor with a DSP instruction set and a
ARM
5-2.480GHz, air-interface rate 250Kbps
Primary application fields
1.2
Smart
Smart homes/appliances
Industrial wireless control
Health and measurements
Asset tracking
buildings
Smart plugs, smart light
ing
1
Version1.0.0
TYZS5 V1.0.0 Datasheet
2. Module interfaces
2.1
Package dimensions
The TYZS5 has 2 rows of pins with a 2mm gap and a total of 14 external pins.
TYZS5 dimensions: 14.8mm (W) x 20.4mm (L) x 2.0mm (H),TYZS5 dimensions are as shown in Figure 1: .
1.
2 :
2
Version1.0.0
TYZS5 V1.0.0 Datasheet
2.2 Pin
Pin
number
1 PWM1 I/O Light driver port/GPIO pin usage.
2 PWM2 I/O Light driver port/GPIO pin usage.
3 I2C_SDA I/O I2C_SDA, GPIO pin usage.
4 I2C_SCL I/O I2C_SCL, GPIO pin usage.
5 VCC P
6 ADC AI
7 GND P The reference ground of the module.
0 SWDIO I/O
00 SWCLK I/O
8 RXD I/O UART0_RXD, RX serial port.
9 nRST I
10 VCC P
11 TXD O UART0_TXD, TX serial port.
12 GND P
analog input pin.
information.
is not used, it needs to be left floating.
software.
definition
Interface pins are
Symbol IO type Function
Description: P indicates the power pin; I/O indicates the input/output pin; AI indicates
nRST is only the module hardware reset pin; it cannot clear Zigbee net-pairing
(1): This pin can only be used as an ADC port. It cannot be used as a normal IO port. If it
As an ADC input, the input voltage range is limited to 0-AVDD and can be configured by
defined as shown in Table 1:
Table 1, TYZS5 interface pins description
Module power supply pin (common supply
voltage: 3.3V)
ADC, 12-bit
precision SAR analog to digital converter
JLINK SWDIO programming pin. Can be used as a
GPIO pin in normal applications.
JLINK SWCLK programming pin. Can be used as
a GPIO pin in normal applications.
Hardware reset pin, the chip is reset when the pin is
LOW; Power-on reset of the module, the user can
use this pin as needed.
Module power supply pin (common supply
voltage: 3.3V); Since there’s an internal connection
to the 3.3V network, no external handling is
necessary.
The reference ground of the module is internally
connected to GND and does not need to be handled
externally.
2.3 Test point definition
Test pins are defined in Table 2:
Table 2, TYZS5 test pins description
Pin
number
Symbol IO type Function
- ~ I For module production testing
Description: This test pin is bottom PAD and is not recommended for use.
3
Version1.0.0
Loading...