C
3&DATASHEET&
TYL
Tuya Smart BLE Module
1. Product Overview
TYLC3 is a Bluetooth (BLE) module designed by HangZhou Tuya Technology Corporation,
which is designed for outputting LED control signals. The BLE Module consists of a highly
integrated wireless Bluetooth chip TLSR8266F512ET32 and some extra electric circuits that have
been programed with Bluetooth network protocol and plenty of software examples. TYLC3
include a 32-bit CPU, BLE, 512K byte flash, 16k SRAM and 4-channel PWM.
Users can customize their LED products by using these PWM signals.
Figure 1 shows the block diagram of the TYLC3.
Figure 1. The block diagram of the TYLC3
1.1 Features
² Integrated low power consumption 32-bit CPU, also known as application processor
² Basic frequency of the CPU can support 48 MHz
² Supply voltage range: 1.9V to 3.6V
² Peripherals: 4*PWM
² BLE RF features:
l Compatible with BLE 4.0
l Transmitting data rate can go up to 1Mbps
l TX transmitting power: +7dBm
l RX receiving sensitivity: -92dBm
l AES hardware encryption
l On-board PCB antenna
TYLC3&DATASHEET&
l Operating temperature range: -20℃ to 85℃
1.2 Main Application Fields
² Intelligent LED
² Intelligent household applications
2. Dimensions and Footprint
2.1 Dimensions
C3&DATASHEET&
TYL
TYLC3 has
Size of TYLC3: 20mm(W)*26mm(L).
Figure 2 shows the dimensions of TYLC3.
2 columns of Pins. The distance between each Pin is 2.0mm.
Figure 2. The dimensions of TYLC3
2.2 Pin Definition
Table 1 shows the general pin attributes of TYLC3
Table 1. The typical pin definition of TYLC3
PIN&NO.& NAME& TYPE& DESCRIPTION&
1& NC& /& No
2& NC& /& No
3& 3.
4& GND& P& Gr
5& W& I/
6& B& I/
7& G& I/
8& R& I/
9& SW& I/
10& GND& P& Gr
11& 3.
Not
e: S: Power supply pins; I/O: Digital input or output pins.
If there’s any customization needed for PWM output, please contact our BD manager.
3V& P& Supply&voltage&
O& PWM&output&pin,&default&for&White&LED&line&
O& PWM&output&pin,&default&for&Blue&LED&line&
O& PWM&output&pin,&default&for&Green&LED&line&
O& PWM&output&pin,&default&for&Red&LED&line&
O& Bluetooth&chipset&burning&pin&
ound&for&Bluetooth&chipset&burning&
3V& P& Supply&voltage&for&Bluetooth&chipset&burning&
n-connected&
n-connected&
ound&
ectrical Characteristics
3. El
3.1 Absolute Maximum Ratings
le 2. Absolute Maximum Ratings
Tab
PA
RAMETERS$ DESCRIPTION$ MIN$ MAX$ UNI
Ts& St
temperature&
C& Supply&voltage& -0.3& 3.9& V&
VC
ectrostatic&release&quantity&
El
(Human&body&model)&
ectrostatic&release&quantity&
El
(Machine&model)&
TAMB-25℃&
TAMB-25℃&
C3&DATASHEET&
TYL
orage&
-20& 85&
-& 2& KV&
-& 0.5& KV&
T$
℃
3.2 Electrical Conditions
le 3. Electrical Conditions
Tab
PA
RAMETERS$ DESCRIPTION$ MIN$ TYPIC
AL$
Ta& Te
VC
C& Supply&voltage& 1.9& 3.3& 3.6& V&
VI
L& IO&negative&level&input& -0.3& -& VCC*0.25& V&
H& IO&positive&level&input& VCC*0.75& -& VCC& V&
VI
L& IO&negative&level&outpu t& -& -& VCC*0.1& V&
VO
Vo
H& IO&positive&level&output& VCC*0.8& -& VCC& V&
mperature&for&Commercial&grade& -20& -& 85&
MAX$ UNIT$
3.3 Transmitting Current Consumptions
Ta
ble 4. TX current consumption
PA
RAMETERS$ MODE$ TYPICAL$ UNIT$
Itx&
x& Continuously&receiving& 13& mA&
Ir
C& Normal&working&mode& 80& uA&
ID
Continuously&transmitting,&7dBm&power&output&
13& mA&
℃
C3&DATASHEET&
TYL
4. Ra
dio Specification
4.1 Basic Radio Frequency Characteristics
ble 5. Basic Radio frequency characteristics
Ta
RAMETERS$ DESCRIPTION$
PA
rking&Frequency& 2.4GHz&ISM&band&
Wo
dio&standard& BLE&4.0&
Ra
Da
ta&transmitting&rate& 1Mbps
Ty
pe&of&Antenna& On-board&PCB&Antenna(default)&
4.2 Transmitting Power
ble 6. Transmitting power
Ta
PA
RAMETERS$ MIN$ TYPICAL$ MAX$ UNIT$
RF
& Average& output& power&
consumption&
B&bandwidth& -& 1000& -& KHz&
20d
3.8& 7& -& dBm&
4.3 Receiving Sensitivity
Ta
ble 7. Receiving sensitivity
PA
RAMETERS$ MIN$ TYPICAL$ MAX$ UNIT$
RX&se
nsitivity& 1Mbps& -93& -92& -90& dBm&
Fr
equency&bias&error& -& -300& -& 300& KH z&
annel&interference&Restrain& -& -& -7& -& dB&
Co-ch
TYLC3&DATASHEET&
5. Antenna Information
5.1 Antenna Type
Antenna can be connected using On-board PCB antenna only.
5.2 Reduce Antenna Interference
In order to have the best RF performance, it’s recommended to keep a minimum 15mm
distance between the antenna part and the other metal pieces.
TYLC3&DATASHEET&
6. Packaging Information And Production Guide
6.1 Mechanical Dimensions
Figure 3. Dimensions of the module
6.2 Production Guide
² The storage for the delivered module should meet the following condition:
1. The anti-moisture bag should be kept in the environment with temperature < 30℃ and
humidity < 85% RH.
2. The expiration date is 6 months since the dry packaging products was sealed.
² Cautions:
1. All the operators should wear electrostatic ring in the whole process of production.
2. While operating, water and dirt should not have any contact with the modules.
FCC Statement
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment .This
minimum distance 20cm between the radiator
Label Instructions
FCC
equipment should be installed and operated with
& your body.
The outside of final products that contains this module device must display a label referring to the
enclosed module. This exterior label can use wording such as: "Contains Transmitter Module FCC
ID: 2ANDL-TYLC3 or “Contains FCC ID:2ANDL-TYLC3 , Any similar wording that expresses
the same meaning may be used.
Loading...